| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Cirque touchpads with PID D0C1 generate an error when probed
by the I2C HID driver, resulting in no hidraw device created.
Adding I2C_HID_QUIRK_NO_IRQ_AFTER_RESET fixes the issue.
Signed-off-by: Vadim Klishko <vadim@cirque.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
- add support for devices that provide HID descriptor solely through ACPI _DSM
method (XIE Zhibang)
|
|
- initial support for 2026 Steam Controller (Vicki Pfau)
- support for sensor events on the 2025 Steam Controller (Vicki Pfau)
- assorted fixes, improvements and code refactoring (Vicki Pfau)
|
|
If enabling VDDIO fails after VDD has been enabled, the power-up
path returns without disabling VDD. This leaves the regulator enabled
and its enable count unbalanced.
Disable VDD before returning the VDDIO error.
Fixes: eb16f59e8e58 ("HID: i2c-hid: goodix: Add mainboard-vddio-supply")
Signed-off-by: Chao Huang <huangchao@kylinos.cn>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
When i2c-hid fails to read the HID report descriptor during device
initialization, the error message prints as:
hid (null): reading report descriptor failed
The HID device name is set in hid_add_device() after calling
hdev->ll_driver->parse(), so when i2c_hid_parse() fails and calls
hid_err(), the device name has not been set yet, resulting in "(null)"
output.
Use dev_err(&client->dev, ...) instead of hid_err(hid, ...) because
the I2C client device is fully initialized with a proper name, providing
meaningful error messages for debugging.
Before: hid (null): reading report descriptor failed
After: i2c_hid i2c-TPD0001:00: reading report descriptor failed
Fixes: 4a200c3b9a40 ("HID: i2c-hid: introduce HID over i2c specification implementation")
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Move the _DSM call that gets the HID descriptor address from
i2c-hid-acpi.c into i2c-hid-acpi.h as a static inline so both the ACPI
and the new PRP0001 driver can use it. While refactoring, move the
blacklist check and the _DSM call to the top of probe() to avoid a
pointless alloc when the device is blacklisted or does not implement the
_DSM.
Some devices, for example the Lenovo KaiTian N60d and Inspur CP300L3,
are declared with _HID "PRP0001" and _DSD compatible "hid-over-i2c" but
lack "hid-descr-addr" from the _DSD and provide the HID descriptor
address only through an ACPI _DSM. The OF driver fails to probe them
because it requires hid-descr-addr. Add a new driver that handles these
devices by calling the shared _DSM helper.
Link: https://lore.kernel.org/tencent_F6FC553D1BB737FC00062AD0FEF43C580F0A@qq.com
Fixes: b33752c30023 ("HID: i2c-hid: Reorganize so ACPI and OF are separate modules")
Signed-off-by: 谢致邦 (XIE Zhibang) <Yeking@Red54.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
files)
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
|
|
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
This patch doesn't modify the compiled array, only its representation in
source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- fixes for a few OOB/UAF in several HID drivers (Florian Pradines, Lee
Jones, Michael Zaidman, Rosalie Wanders, Sangyun Kim and Tomasz
Pakuła)
- more general sanitation of input data, dealing with potentially
malicious hardware in hid-core (Benjamin Tissoires)
- a few device-specific quirks and fixups
* tag 'hid-for-linus-2026051401' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: logitech-hidpp: Add support for newer Bluetooth keyboards
HID: pidff: Fix integer overflow in pidff_rescale
HID: i2c-hid: add reset quirk for BLTP7853 touchpad
HID: core: introduce hid_safe_input_report()
HID: pass the buffer size to hid_report_raw_event
HID: google: hammer: stop hardware on devres action failure
HID: appletb-kbd: run inactivity autodim from workqueues
HID: appletb-kbd: fix UAF in inactivity-timer cleanup path
HID: playstation: Clamp num_touch_reports
HID: magicmouse: Prevent out-of-bounds (OOB) read during DOUBLE_REPORT_ID
HID: mcp2221: fix OOB write in mcp2221_raw_event()
HID: quirks: really enable the intended work around for appledisplay
HID: hid-sjoy: race between init and usage
HID: uclogic: Fix regression of input name assignment
HID: intel-thc-hid: Intel-quickspi: Fix some error codes
HID: hid-lenovo-go-s: restore OS_TYPE after resume from s2idle
HID: elan: Add support for ELAN SB974D touchpad
HID: sony: add missing size validation for Rock Band 3 Pro instruments
HID: sony: add missing size validation for SMK-Link remotes
HID: sony: remove unneeded WARN_ON() in sony_leds_init()
...
|
|
The BLTP7853 I2C HID touchpad may fail to probe after reboot or
reprobe because reset completion is not signalled to the host. The
driver then waits for the reset-complete interrupt until it times out
and the device probe fails:
i2c_hid i2c-BLTP7853:00: failed to reset device.
i2c_hid i2c-BLTP7853:00: can't add hid device: -61
i2c_hid: probe of i2c-BLTP7853:00 failed with error -61
Add I2C_HID_QUIRK_NO_IRQ_AFTER_RESET for the device so i2c-hid does
not wait for a reset interrupt that may never arrive.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
hid_input_report() is used in too many places to have a commit that
doesn't cross subsystem borders. Instead of changing the API, introduce
a new one when things matters in the transport layers:
- usbhid
- i2chid
This effectively revert to the old behavior for those two transport
layers.
Fixes: 0a3fe972a7cb ("HID: core: Mitigate potential OOB by removing bogus memset()")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Sync up with the mainline to brig up the latest changes, specifically
changes to ALPS driver.
|
|
Parade-tc3408 requires reset to pull down time greater than 10ms,
so the configuration post_power_delay_ms is 10, and the chipset
initial time is required to be greater than 300ms,
so the post_gpio_reset_on_delay_ms is set to 300.
Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://patch.msgid.link/20260108063524.742464-3-yelangyan@huaqin.corp-partner.google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- support for FocalTech FT8112 added to i2c-hid driver
- support for FocalTech FT3518 added to edt-ft5x06 driver
- support for power buttons in TWL603x chips added to twl4030-pwrbutton
driver
- an update to gpio-decoder driver to make it usable on non-OF
platforms and to clean up the code
- an update to synaptics_i2c driver switching it to use managed
resources and a fix to restarting polling after resume
- an update to gpio-keys driver to fall back to getting IRQ from
resources if not specified using other means
- an update to ili210x driver to support polling mode
- a number of input drivers switched to scnprintf() to suppress
truncation warnings
- a number of updates and conversions of device tree bindings to yaml
format
- fixes to spelling in comments and messages in several drivers
- other assorted fixups
* tag 'input-for-v7.0-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
dt-bindings: input: qcom,pm8941-pwrkey: Document PMM8654AU
dt-bindings: input: touchscreen: imagis: allow linux,keycodes for ist3038
Input: apbps2 - fix comment style and typos
Input: gpio_keys - fall back to platform_get_irq() for interrupt-only keys
Input: novatek-nvt-ts - drop wake_type check
dt-bindings: input: touchscreen: tsc2007: document '#io-channel-cells'
Input: ili210x - add support for polling mode
dt-bindings: touchscreen: trivial-touch: Drop 'interrupts' requirement for old Ilitek
Input: appletouch - fix potential race between resume and open
HID: i2c-hid: Add FocalTech FT8112
dt-bindings: input: i2c-hid: Introduce FocalTech FT8112
Input: synaptics_i2c - switch to using managed resources
Input: synaptics_i2c - guard polling restart in resume
Input: gpio_decoder - don't use "proxy" headers
Input: gpio_decoder - make use of the macros from bits.h
Input: gpio_decoder - replace custom loop by gpiod_get_array_value_cansleep()
Input: gpio_decoder - unify messages with help of dev_err_probe()
Input: gpio_decoder - make use of device properties
Input: serio - complete sizeof(*pointer) conversions
Input: wdt87xx_i2c - switch to use dev_err_probe()
...
|
|
Information for touchscreen model HKO/RB116AS01-2 as below:
- HID :FTSC1000
- slave address:0X38
- Interface:HID over I2C
- Touch control lC:FT8112
- I2C ID: PNP0C50
Signed-off-by: Daniel Peng <Daniel_Peng@pegatron.corp-partner.google.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20251117094041.300083-2-Daniel_Peng@pegatron.corp-partner.google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
`i2c_hid_xfer` is used to read `recv_len + sizeof(__le16)` bytes of data
into `ihid->rawbuf`.
The former can come from the userspace in the hidraw driver and is only
bounded by HID_MAX_BUFFER_SIZE(16384) by default (unless we also set
`max_buffer_size` field of `struct hid_ll_driver` which we do not).
The latter has size determined at runtime by the maximum size of
different report types you could receive on any particular device and
can be a much smaller value.
Fix this by truncating `recv_len` to `ihid->bufsize - sizeof(__le16)`.
The impact is low since access to hidraw devices requires root.
Signed-off-by: Kwok Kin Ming <kenkinming2002@gmail.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- haptic touchpad support (Angela Czubak and Jonathan Denose)
- support for audio jack handling on DualSense Playstation controllers
(Cristian Ciocaltea)
- allow HID-BPF to rebind a driver to hid-multitouch (Benjamin
Tissoires)
- rework hidraw ioctls to make them safer (and tested) (Benjamin
Tissoires)
- various PIDFF and universal-PIDFF fixes/improvements (Tomasz Pakuła)
- better configuration of Intel QuickI2C through ACPI (Xinpeng Sun)
- other assorted cleanups and fixes
* tag 'hid-for-linus-2025093001' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (58 commits)
HID: playstation: Switch to scoped_guard() in {dualsense|dualshock4}_output_worker()
HID: playstation: Silence sparse warnings for locking context imbalances
HID: playstation: Update SP preamp gain comment line
HID: intel-thc-hid: intel-quicki2c: support ACPI config for advanced features
HID: core: Change hid_driver to use a const char* for name
HID: hidraw: tighten ioctl command parsing
selftests/hid: hidraw: forge wrong ioctls and tests them
selftests/hid: hidraw: add more coverage for hidraw ioctls
selftests/hid: update vmtest.sh for virtme-ng
HID: playstation: Support DualSense audio jack event reporting
HID: playstation: Support DualSense audio jack hotplug detection
HID: playstation: Redefine DualSense input report status field
HID: playstation: Prefer kzalloc(sizeof(*buf)...)
HID: playstation: Document spinlock_t usage
HID: playstation: Fix all alignment and line length issues
HID: playstation: Correct spelling in comment sections
HID: playstation: Replace uint{32,16,8}_t with u{32,16,8}
HID: playstation: Simplify locking with guard() and scoped_guard()
HID: playstation: Add spaces around arithmetic operators
HID: playstation: Make use of bitfield macros
...
|
|
Dell systems utilize an EC-based touchpad emulation when the ACPI
touchpad _DSM is not invoked. This emulation acts as a secondary
master on the I2C bus, designed for scenarios where the I2C touchpad
driver is absent, such as in BIOS menus. Typically, loading the
i2c-hid module triggers the _DSM at initialization, disabling the
EC-based emulation.
However, if the i2c-hid module is missing from the boot kernel
used for hibernation snapshot restoration, the _DSM remains
uncalled, resulting in dual masters on the I2C bus and
subsequent arbitration errors. This issue arises when i2c-hid
resides in the rootfs instead of the kernel or initramfs.
To address this, switch from using the SYSTEM_SLEEP_PM_OPS()
macro to dedicated callbacks, introducing a specific
callback for restoring the S4 image. This callback ensures
the _DSM is invoked.
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Bitwise AND was intended instead of OR. With the current code the
condition is always true.
Fixes: cbdd16b818ee ("HID: i2c-hid: Make elan touch controllers power on after panel is enabled")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/aK8Au3CgZSTvfEJ6@stanley.mountain
|
|
Introduce a new HID quirk to indicate that this device has to be enabled
after the panel's backlight is enabled, and update the driver data for
the elan devices to enable this quirk. This cannot be a I2C HID quirk
because the kernel needs to acknowledge this before powering up the
device and read the VID/PID. When this quirk is enabled, register
.panel_enabled()/.panel_disabling() instead for the panel follower.
Also rename the *panel_prepare* functions into *panel_follower* because
they could be called in other situations now.
Fixes: bd3cba00dcc63 ("HID: i2c-hid: elan: Add support for Elan eKTH6915 i2c-hid touchscreens")
Fixes: d06651bebf99e ("HID: i2c-hid: elan: Add elan-ekth6a12nay timing")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250818115015.2909525-2-treapking@chromium.org
|
|
We have two places to print "failed to set a report to ...",
use "get a report from" instead of "set a report to", it makes
people who knows less about the module to know where the error
happened.
Before:
i2c_hid_acpi i2c-FTSC1000:00: failed to set a report to device: -11
After:
i2c_hid_acpi i2c-FTSC1000:00: failed to get a report from device: -11
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
In drivers/hid/, most drivers depend on CONFIG_HID, while a couple of the
drivers in subdirectories instead depend on CONFIG_HID_SUPPORT and use
'select HID'. With the newly added INTEL_THC_HID, this causes a build
warning for a circular dependency:
WARNING: unmet direct dependencies detected for HID
Depends on [m]: HID_SUPPORT [=y] && INPUT [=m]
Selected by [y]:
- INTEL_THC_HID [=y] && HID_SUPPORT [=y] && X86_64 [=y] && PCI [=y] && ACPI [=y]
WARNING: unmet direct dependencies detected for INPUT_FF_MEMLESS
Depends on [m]: INPUT [=m]
Selected by [y]:
- HID_MICROSOFT [=y] && HID_SUPPORT [=y] && HID [=y]
- GREENASIA_FF [=y] && HID_SUPPORT [=y] && HID [=y] && HID_GREENASIA [=y]
- HID_WIIMOTE [=y] && HID_SUPPORT [=y] && HID [=y] && LEDS_CLASS [=y]
- ZEROPLUS_FF [=y] && HID_SUPPORT [=y] && HID [=y] && HID_ZEROPLUS [=y]
Selected by [m]:
- HID_ACRUX_FF [=y] && HID_SUPPORT [=y] && HID [=y] && HID_ACRUX [=m]
- HID_EMS_FF [=m] && HID_SUPPORT [=y] && HID [=y]
- HID_GOOGLE_STADIA_FF [=m] && HID_SUPPORT [=y] && HID [=y]
- PANTHERLORD_FF [=y] && HID_SUPPORT [=y] && HID [=y] && HID_PANTHERLORD [=m]
It's better to be consistent and always use 'depends on HID' for HID
drivers. The notable exception here is USB_KBD/USB_MOUSE, which are
alternative implementations that do not depend on the HID subsystem.
Do this by extending the "if HID" section below, which means that a few
of the duplicate "depends on HID" and "depends on INPUT" statements
can be removed in the process.
Fixes: 1b2d05384c29 ("HID: intel-thc-hid: Add basic THC driver skeleton")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Even Xu <even.xu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
This solves keyboard not working until suspend&resume issue on Dell XPS
9345 13" (codenamed 'tributo').
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
It appears some keyboards from vendor 'QTEC' will not work properly until
suspend & resume.
Empirically narrowed down to solution of re-sending power on command
_after_ initialization was completed before the end of initial probing.
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
commit 7d6f065de37c ("HID: i2c-hid: Use address probe to wake on resume")
replaced the retry of power commands with the dummy read "bus probe" we
use on boot which accounts for a necessary delay before retry.
This made at least one Weida device (2575:0910 in an ASUS Vivobook S14)
very unhappy, as the bus probe despite being successful somehow lead to
the following power command failing so hard that the device never lets
go of the bus. This means that even retries of the power command would
fail on a timeout as the bus remains busy.
Remove the bus probe on resume and instead reintroduce retry of the
power command for wake-up purposes while respecting the newly
established wake-up retry timings.
Fixes: 7d6f065de37c ("HID: i2c-hid: Use address probe to wake on resume")
Cc: stable@vger.kernel.org
Reported-by: Michael <auslands-kv@gmx.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219440
Link: https://lore.kernel.org/r/d5acb485-7377-4139-826d-4df04d21b5ed@leemhuis.info/
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Link: https://patch.msgid.link/20241119235615.23902-1-kl@kl.wtf
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
- code cleanup (Uwe Kleine-König)
|
|
- Sanitization of BTN_TOOL_RUBBER handling (Jason Gerecke)
|
|
Patch for Goodix 27c6:0d42 touchpads found in Inspiron 5515 laptops.
After resume from suspend, one can communicate with this device just fine.
We can read data from it or request a reset,
but for some reason the interrupt line will not go up
when new events are available.
(it can correctly respond to a reset with an interrupt tho)
The only way I found to wake this device up
is to send anything to it after ~1.5s mark,
for example a simple read request, or power mode change.
In this patch, I simply delay the resume steps with msleep,
this will cause the set_power request to happen after
the ~1.5s barrier causing the device to resume its event interrupts.
Sleep was used rather than delayed_work
to make this workaround as non-invasive as possible.
[jkosina@suse.com: shortlog update]
Signed-off-by: Bartłomiej Maryńczak <marynczakbartlomiej@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
i2c_device_id::driver_data to 0
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While touching the initializer, also remove the comma after the sentinel
entry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
- Add support for one new Elan device (ekth6a12nay) (Zhaoxiong Lv)
|
|
i2c-hid uses 2 shared buffers: command and "raw" input buffer for
sending requests to peripherals and read data from peripherals when
executing variety of commands. Such commands include reading of HID
registers, requesting particular power mode, getting and setting
reports and so on. Because all such requests use the same 2 buffers
they should not execute simultaneously.
Fix this by introducing "cmd_lock" mutex and acquire it whenever
we needs to access ihid->cmdbuf or idid->rawbuf.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Elan-ekth6a12nay requires reset to pull down time greater than 10ms,
so the configuration post_power_delay_ms is 10, and the chipset
initial time is required to be greater than 300ms,
so the post_gpio_reset_on_delay_ms is set to 300.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Zhaoxiong Lv <lvzhaoxiong@huaqin.corp-partner.google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
The Elan eKTH5015M touch controller found on the Lenovo ThinkPad X13s
shares the VCC33 supply with other peripherals that may remain powered
during suspend (e.g. when enabled as wakeup sources).
The reset line is also wired so that it can be left deasserted when the
supply is off.
This is important as it avoids holding the controller in reset for
extended periods of time when it remains powered, which can lead to
increased power consumption, and also avoids leaking current through the
X13s reset circuitry during suspend (and after driver unbind).
Use the new 'no-reset-on-power-off' devicetree property to determine
when reset needs to be asserted on power down.
Notably this also avoids wasting power on machine variants without a
touchscreen for which the driver would otherwise exit probe with reset
asserted.
Fixes: bd3cba00dcc6 ("HID: i2c-hid: elan: Add support for Elan eKTH6915 i2c-hid touchscreens")
Cc: <stable@vger.kernel.org> # 6.0
Cc: Douglas Anderson <dianders@chromium.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240507144821.12275-5-johan+linaro@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
- PM fixes for STM and Weida Tech devices (Kenny Levinsen)
|
|
This label was left behind when the wake-up logic was moved from
i2c_hid_set_power to i2c_hid_probe_address. Clean it up as it causes
warnings-as-errors builds to fail.
Fixes: bb1033c8a3ea ("HID: i2c-hid: Use address probe to wake on resume")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Certain devices, both from STM and Weida Tech, need to be woken up after
having entered a deeper sleep state. The relevant places to wake up such
device is during our initial HID probe, and after resuming.
A retry for power commands was previously added to i2c_hid_set_power to
wake up Weida Tech devices, but lacked sufficient sleep for STM devices.
Replace the power command retry with the same address probe we using
during our initial HID probe.
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Some STM microcontrollers need 400µs after rising clock edge in order to
come out of their deep sleep state. This in turn means that our address
probe will fail as the device is not ready to service it.
Retry the probe once after a delay to see if the device came alive,
otherwise treat the device as missing.
Link: https://lore.kernel.org/all/20240405102436.3479210-1-lma@chromium.org/#t
Co-developed-by: Radoslaw Biernacki <rad@chromium.org>
Co-developed-by: Lukasz Majczak <lma@chromium.org>
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
In af93a167eda9, i2c_hid_parse was changed to continue with reading the
report descriptor before waiting for reset to be acknowledged.
This has lead to two regressions:
1. We fail to handle reset acknowledgment if it happens while reading
the report descriptor. The transfer sets I2C_HID_READ_PENDING, which
causes the IRQ handler to return without doing anything.
This affects both a Wacom touchscreen and a Sensel touchpad.
2. On a Sensel touchpad, reading the report descriptor this quickly
after reset results in all zeroes or partial zeroes.
The issues were observed on the Lenovo Thinkpad Z16 Gen 2.
The change in question was made based on a Microsoft article[0] stating
that Windows 8 *may* read the report descriptor in parallel with
awaiting reset acknowledgment, intended as a slight reset performance
optimization. Perhaps they only do this if reset is not completing
quickly enough for their tastes?
As the code is not currently ready to read registers in parallel with a
pending reset acknowledgment, and as reading quickly breaks the report
descriptor on the Sensel touchpad, revert to waiting for reset
acknowledgment before proceeding to read the report descriptor.
[0]: https://learn.microsoft.com/en-us/windows-hardware/drivers/hid/plug-and-play-support-and-power-management
Fixes: af93a167eda9 ("HID: i2c-hid: Move i2c_hid_finish_hwreset() to after reading the report-descriptor")
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2271136
Cc: stable@vger.kernel.org
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Link: https://lore.kernel.org/r/20240331182440.14477-1-kl@kl.wtf
[hdegoede@redhat.com Drop no longer necessary abort_reset error exit path]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
The flag I2C_HID_READ_PENDING is used to serialize I2C operations.
However, this is not necessary, because I2C core already has its own
locking for that.
More importantly, this flag can cause a lock-up: if the flag is set in
i2c_hid_xfer() and an interrupt happens, the interrupt handler
(i2c_hid_irq) will check this flag and return immediately without doing
anything, then the interrupt handler will be invoked again in an
infinite loop.
Since interrupt handler is an RT task, it takes over the CPU and the
flag-clearing task never gets scheduled, thus we have a lock-up.
Delete this unnecessary flag.
Reported-and-tested-by: Eva Kurchatova <nyandarknessgirl@gmail.com>
Closes: https://lore.kernel.org/r/CA+eeCSPUDpUg76ZO8dszSbAGn+UHjcyv8F1J-CUPVARAzEtW9w@mail.gmail.com
Fixes: 4a200c3b9a40 ("HID: i2c-hid: introduce HID over i2c specification implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
A while back the I2C HID implementation was split in an ACPI and OF
part, but the new OF driver never initialises the client pointer which
is dereferenced on power-up failures.
Fixes: b33752c30023 ("HID: i2c-hid: Reorganize so ACPI and OF are separate modules")
Cc: stable@vger.kernel.org # 5.12
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
There's a Cirque touchpad that wakes system up without anything touched
the touchpad. The input report is empty when this happens.
The reason is stated in HID over I2C spec, 7.2.8.2:
"If the DEVICE wishes to wake the HOST from its low power state, it can
issue a wake by asserting the interrupt."
This is fine if OS can put system back to suspend by identifying input
wakeup count stays the same on resume, like Chrome OS Dark Resume [0].
But for regular distro such policy is lacking.
Though the change doesn't bring any impact on power consumption for
touchpad is minimal, other i2c-hid device may depends on SLEEP control
power. So use a quirk to limit the change scope.
[0] https://chromium.googlesource.com/chromiumos/platform2/+/HEAD/power_manager/docs/dark_resume.md
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
- rework of wait-for-reset in order to reduce the need
for I2C_HID_QUIRK_NO_IRQ_AFTER_RESET qurk; the success rate is now
50% better, but there are still further improvements to be made (Hans de Goede)
|
|
ILI2901 requires reset to pull down time greater than 10ms,
so the configuration post_power_delay_ms is 10, and the chipset
initial time is required to be greater than 100ms,
so the post_gpio_reset_on_delay_ms is set to 100.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zhengqiao Xia <xiazhengqiao@huaqin.corp-partner.google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
The quirks variable and the I2C_HID_QUIRK_ defines are never used /
exported outside of the i2c-hid code renumber them to start at
BIT(0) again.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Re-trying the power-on command on failure on all devices should
not be a problem, drop the I2C_HID_QUIRK_SET_PWR_WAKEUP_DEV quirk
and simply retry power-on on all devices.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
On all i2c-hid devices seen sofar the reset-ack either works, or the hw is
somehow buggy and does not (always) ack the reset properly, yet it still
works fine.
Lower the very long reset timeout to 1 second which should be plenty
and change the reset not getting acked from an error into a warning.
This results in a bit cleaner code and avoids the need to add more
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET quirks in the future.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
report-descriptor
A recent bug made me look at Microsoft's i2c-hid docs again
and I noticed the following:
"""
4. Issue a RESET (Host Initiated Reset) to the Device.
5. Retrieve report descriptor from the device.
Note: Steps 4 and 5 may be done in parallel to optimize for time on I²C.
Since report descriptors are (a) static and (b) quite long, Windows 8 may
issue a request for 5 while it is waiting for a response from the device
on 4.
"""
Which made me think that maybe on some touchpads the reset ack is delayed
till after the report descriptor is read ?
Testing a T-BAO Tbook Air 12.5 with a 0911:5288 (SIPODEV SP1064?) touchpad,
for which the I2C_HID_QUIRK_NO_IRQ_AFTER_RESET quirk was first introduced,
shows that reading the report descriptor before waiting for the reset
helps with the missing reset IRQ. Now the reset does get acked properly,
but the ack sometimes still does not happen unfortunately.
Still moving the wait for ack to after reading the report-descriptor,
is probably a good idea, both to make i2c-hid's behavior closer to
Windows as well as to speed up probing i2c-hid devices.
While at it drop the dbg_hid() for a malloc failure, malloc failures
already get logged extensively by malloc itself.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2247751
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Switch i2c_hid_parse() to goto style error handling.
This is a preparation patch for removing the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET by making i2c-hid behave
more like Windows.
Note this changes the descriptor read error path to propagate
the actual i2c_hid_read_register() error code (which is always
negative) instead of hardcoding a -EIO return.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Split i2c_hid_hwreset() into:
i2c_hid_start_hwreset() which sends the PWR_ON and reset commands; and
i2c_hid_finish_hwreset() which actually waits for the reset to complete.
This is a preparation patch for removing the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET by making i2c-hid behave
more like Windows.
No functional changes intended.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
