| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some Synaptics MST branch devices have a problem decompressing a stream
with a compressed link-bpp higher than 12, if the pixel clock is higher
than ~50 % of the maximum throughput capability reported by the branch
device. The screen remains blank, or for some - mostly black content -
gets enabled, but may stil have jitter artifacts.
At least the following docking stations are affected, based on testing
both with any Intel devices or the UCD-500 reference device as a source:
- DELL WD19DCS, DELL WD19TB3, DELL WD22TB4
- ThinkPad 40AN
- HP G2
At least the following docking stations are free from this problem,
based on tests with a source/sink/mode etc. configuration matching the
test cases used above:
- DELL Dual Charge HD22Q, DELL WD25TB5
- ThinkPad 40B0
- Anker 565
All the affected devices have an older version of the Synaptics MST
branch device (Panamera), whereas all the non-affected docking stations
have a newer branch device (at least Synaptics Panamera with a higher HW
revision number and Synaptics Cayenne models). Add the required quirk
entries accordingly. The quirk will be handled by the i915/xe drivers in
a follow-up change.
The latest firmware version of the Synaptics branch device for all the
affected devices tested above is 5.7 (as reported at DPCD address
0x50a/0x50b). For the DELL devices this corresponds to the latest
01.00.14.01.A03 firmware package version of the docking station.
v2:
- Document the DP_DPCD_QUIRK_DSC_THROUGHPUT_BPP_LIMIT enum.
- Describe the quirk in more detail in the dpcd_quirk_list.
v3:
- s/Panarema/Panamera in the commit log.
Cc: dri-devel@lists.freedesktop.org
Reported-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reported-and-tested-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250930182450.563016-2-imre.deak@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild updates from Nathan Chancellor:
- Extend modules.builtin.modinfo to include module aliases from
MODULE_DEVICE_TABLE for builtin modules so that userspace tools (such
as kmod) can verify that a particular module alias will be handled by
a builtin module
- Bump the minimum version of LLVM for building the kernel to 15.0.0
- Upgrade several userspace API checks in headers_check.pl to errors
- Unify and consolidate CONFIG_WERROR / W=e handling
- Turn assembler and linker warnings into errors with CONFIG_WERROR /
W=e
- Respect CONFIG_WERROR / W=e when building userspace programs
(userprogs)
- Enable -Werror unconditionally when building host programs
(hostprogs)
- Support copy_file_range() and data segment alignment in gen_init_cpio
to improve performance on filesystems that support reflinks such as
btrfs and XFS
- Miscellaneous small changes to scripts and configuration files
* tag 'kbuild-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux: (47 commits)
modpost: Initialize builtin_modname to stop SIGSEGVs
Documentation: kbuild: note CONFIG_DEBUG_EFI in reproducible builds
kbuild: vmlinux.unstripped should always depend on .vmlinux.export.o
modpost: Create modalias for builtin modules
modpost: Add modname to mod_device_table alias
scsi: Always define blogic_pci_tbl structure
kbuild: extract modules.builtin.modinfo from vmlinux.unstripped
kbuild: keep .modinfo section in vmlinux.unstripped
kbuild: always create intermediate vmlinux.unstripped
s390: vmlinux.lds.S: Reorder sections
KMSAN: Remove tautological checks
objtool: Drop noinstr hack for KCSAN_WEAK_MEMORY
lib/Kconfig.debug: Drop CLANG_VERSION check from DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT
riscv: Remove ld.lld version checks from many TOOLCHAIN_HAS configs
riscv: Unconditionally use linker relaxation
riscv: Remove version check for LTO_CLANG selects
powerpc: Drop unnecessary initializations in __copy_inst_from_kernel_nofault()
mips: Unconditionally select ARCH_HAS_CURRENT_STACK_POINTER
arm64: Remove tautological LLVM Kconfig conditions
ARM: Clean up definition of ARM_HAS_GROUP_RELOCS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit updates from Shuah Khan:
- New parameterized test features
KUnit parameterized tests supported two primary methods for getting
parameters:
- Defining custom logic within a generate_params() function.
- Using the KUNIT_ARRAY_PARAM() and KUNIT_ARRAY_PARAM_DESC() macros
with a pre-defined static array and passing the created
*_gen_params() to KUNIT_CASE_PARAM().
These methods present limitations when dealing with dynamically
generated parameter arrays, or in scenarios where populating
parameters sequentially via generate_params() is inefficient or
overly complex.
These limitations are fixed with a parameterized test method
- Fix issues in kunit build artifacts cleanup
- Fix parsing skipped test problem in kselftest framework
- Enable PCI on UML without triggering WARN()
- a few other fixes and adds support for new configs such as MIPS
* tag 'linux_kselftest-kunit-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: Extend kconfig help text for KUNIT_UML_PCI
rust: kunit: allow `cfg` on `test`s
kunit: qemu_configs: Add MIPS configurations
kunit: Enable PCI on UML without triggering WARN()
Documentation: kunit: Document new parameterized test features
kunit: Add example parameterized test with direct dynamic parameter array setup
kunit: Add example parameterized test with shared resource management using the Resource API
kunit: Enable direct registration of parameter arrays to a KUnit test
kunit: Pass parameterized test context to generate_params()
kunit: Introduce param_init/exit for parameterized test context management
kunit: Add parent kunit for parameterized test context
kunit: tool: Accept --raw_output=full as an alias of 'all'
kunit: tool: Parse skipped tests from kselftest.h
kunit: Always descend into kunit directory during build
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"Two small patches for the asm-generic header files: Varad Gautam
improves the MMIO tracing to be faster when the tracepoints are built
into the kernel but disabled, while Qi Xi updates the DO_ONCE logic so
that clearing the WARN_ONCE() flags does not change the other DO_ONCE
users"
* tag 'asm-generic-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
once: fix race by moving DO_ONCE to separate section
asm-generic/io.h: Skip trace helpers if rwmmio events are disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The at91 power management code and the TI AM33 platform each get a few
updates for robustness, the other changes are just minor cleanups"
* tag 'soc-arm-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: versatile: clock: convert from round_rate() to determine_rate()
ARM: rockchip: remove REGULATOR conditional to PM
ARM: at91: pm: Remove 2.5V regulator
ARM: OMAP2+: clock: convert from round_rate() to determine_rate()
ARM: OMAP1: clock: convert from round_rate() to determine_rate()
ARM: mach-hpe: Rework support and directory structure
arm: omap2: use string choices helper
ARM: OMAP2+: pm33xx-core: ix device node reference leaks in amx3_idle_init
ARM: OMAP2+: use IS_ERR_OR_NULL() helper
ARM: AM33xx: Implement TI advisory 1.0.36 (EMU0/EMU1 pins state on reset)
ARM: at91: pm: save and restore ACR during PLL disable/enable
ARM: at91: pm: fix MCKx restore routine
ARM: at91: pm: fix .uhp_udp_mask specification for current SoCs
ARM: shmobile: rcar-gen2: Use SZ_256K definition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Lots of platform specific updates for Qualcomm SoCs, including a new
TEE subsystem driver for the Qualcomm QTEE firmware interface.
Added support for the Apple A11 SoC in drivers that are shared with
the M1/M2 series, among more updates for those.
Smaller platform specific driver updates for Renesas, ASpeed,
Broadcom, Nvidia, Mediatek, Amlogic, TI, Allwinner, and Freescale
SoCs.
Driver updates in the cache controller, memory controller and reset
controller subsystems.
SCMI firmware updates to add more features and improve robustness.
This includes support for having multiple SCMI providers in a single
system.
TEE subsystem support for protected DMA-bufs, allowing hardware to
access memory areas that managed by the kernel but remain inaccessible
from the CPU in EL1/EL0"
* tag 'soc-drivers-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (139 commits)
soc/fsl/qbman: Use for_each_online_cpu() instead of for_each_cpu()
soc: fsl: qe: Drop legacy-of-mm-gpiochip.h header from GPIO driver
soc: fsl: qe: Change GPIO driver to a proper platform driver
tee: fix register_shm_helper()
pmdomain: apple: Add "apple,t8103-pmgr-pwrstate"
dt-bindings: spmi: Add Apple A11 and T2 compatible
serial: qcom-geni: Load UART qup Firmware from linux side
spi: geni-qcom: Load spi qup Firmware from linux side
i2c: qcom-geni: Load i2c qup Firmware from linux side
soc: qcom: geni-se: Add support to load QUP SE Firmware via Linux subsystem
soc: qcom: geni-se: Cleanup register defines and update copyright
dt-bindings: qcom: se-common: Add QUP Peripheral-specific properties for I2C, SPI, and SERIAL bus
Documentation: tee: Add Qualcomm TEE driver
tee: qcom: enable TEE_IOC_SHM_ALLOC ioctl
tee: qcom: add primordial object
tee: add Qualcomm TEE driver
tee: increase TEE_MAX_ARG_SIZE to 4096
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_OBJREF
tee: add TEE_IOCTL_PARAM_ATTR_TYPE_UBUF
tee: add close_context to TEE driver operation
...
|
|
Pull SoC dt updates from Arnd Bergmann:
"There are five sets of new SoCs that get added in existing families,
all of them being either upgrades or cut-down versions of the older
chips:
- Apple M2 Pro, M2 Max and M2 Ultra, used in the 2022/2023 generation
of high-end workstations and laptops from Apple. Linux has been
working on these for a while but stil requires patches.
- Axis Artpec8 is an Armv8 chip based on Samsung Exynos design,
unlike the earlier Armv7 Artpec6 from the same company that was
part of a separate family of chips.
- NXP i.MX91 is a cut-down version of i.MX93, using only a single
Cortex-A55 core.
- Qualcomm Lemans Auto is a variant of the Lemans SoC that was
originally merged under the sa8775p name, the differences being
mostly the firmware configuration of the platform.
- Four new Renesas SoCs RZ/T2H (r9a09g077m44), RZ/N2H (r9a09g087m44),
RZ/T2H (r9a09g077), and RZ/N2H (r9a09g087) are all industrial
bedded SoCs based on Cortex-A55 cores
In total, there are 65 new machines, including:
- Industrial embedded system and single-board computers based on NXP,
Allwinner, TI, Rockchips, Marvell, Xilinx Spacemit, Starfive chips.
- Reference boards for the newly added Renesas, Qualcomm, NXP and
Axis ARMv8 chips as well as Microchip's MPFS RISC-V SoC
- Laptops and Workstations using Apple M2 and Qualcomm Snapdragon X1
chips.
- Several Samsung phones using Qualcomm Snapdragon chips
- Set-top boxes based on Allwinner H313
- Five BMC boards using 32-bit ASpeed SoCs
- Three network routers using IXP4xx (ARMv5!) and Broadcom bcm4708
(ARMv7) SoCs
Two machines get phased out because they were available only in small
quantities but never made it into products: one STi407 based reference
board, and a Snapdragon 845 based Chromebook.
Aside from the newly added machines, a lot of work went into improving
hardware support on the existing machines and cleaning up contents for
validation"
* tag 'soc-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (931 commits)
arm64: dts: apm-shadowcat: Drop "apm,xgene2-pcie" compatible
arm64: dts: apm-shadowcat: Move slimpro nodes out of "simple-bus" node
ARM: dts: microchip: sam9x7: Add qspi controller
arm64: dts: qcom: Add MST pixel streams for displayport
arm64: dts: qcom: sm6350: correct DP compatibility strings
arm64: dts: qcom: monaco-evk: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300-ride: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300: Add gpu and gmu nodes
arm64: dts: allwinner: h313: Add Amediatech X96Q
dt-bindings: arm: sunxi: Add Amediatech X96Q
arm64: dts: apple: t8015: Add SPMI node
arm64: dts: apple: t8012: Add SPMI node
arm64: dts: apple: Add J180d (Mac Pro, M2 Ultra, 2023) device tree
arm64: dts: rockchip: Add devicetree for the ROC-RK3588-RT
dt-bindings: arm: rockchip: Add Firefly ROC-RK3588-RT
arm64: dts: rockchip: update pinctrl names for Radxa E52C
arm64: dts: rockchip: remove vcc_3v3_pmu regulator for Radxa E52C
arm64: dts: apple: Add J474s, J475c and J475d device trees
arm64: dts: apple: Add J414 and J416 Macbook Pro device trees
arm64: dts: apple: Add initial t6020/t6021/t6022 DTs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Update dtc to upstream version v1.7.2-35-g52f07dcca47c
- Add stub for of_get_next_child_with_prefix()
- Convert of_msi_map_id() callers to of_msi_xlate()
DT bindings:
- Convert multiple text board bindings to DT schema format
- Add bindings for synaptics,synaptics_i2c touchscreen controller,
innolux,n133hse-ea1 and nlt,nl12880bc20-spwg-24 displays, and NXP
vf610 reboot controller
- Add new Arm Cortex-A320/A520AE/A720AE and C1-Nano/Pro/Premium/Ultra
CPUs. Add missing Applied Micro CPU compatibles. Add pu-supply and
fsl,soc-operating-points properties for CPU nodes.
- Add QCom Glymur PDC and tegra264-agic interrupt controllers
- Add samsung,exynos8890-mali GPU to Arm Mali Midgard
- Drop Samsung S3C2410 display related bindings
- Allow separate DP lane and AUX connections in dp-connector
- Add some missing, undocumented vendor prefixes
- Add missing '#address-cells' properties in interrupt controller
bindings which dtc now warns about
- Drop duplicate socfpga-sdram-edac.txt, moxa,moxart-watchdog.txt,
fsl/mpic.txt, ti,opa362.txt, and cavium-thunder2.txt legacy text
bindings which are already covered by existing schemas.
- Various binding fixes for Mediatek platforms in mailbox, regulator,
pinctrl, timer, and display
- Drop work-around for yamllint quoting of values containing ','
- Various spelling, typo, grammar, and duplicated words fixes in DT
bindings and docs
- Add binding guidelines for defining properties at top level of
schemas, lack of node name ABI, and usage of simple-mfd"
* tag 'devicetree-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (81 commits)
dt-bindings: arm: altera: Drop socfpga-sdram-edac.txt
dt-bindings: gpu: Convert nvidia,gk20a to DT schema
dt-bindings: rng: sparc_sun_oracle_rng: convert to DT schema
dt-bindings: vendor-prefixes: update regex for properties without a prefix
dt-bindings: display: bridge: convert megachips-stdpxxxx-ge-b850v3-fw.txt to yaml
scripts: dt_to_config: fix grammar and a typo in --help text
dt-bindings: fix spelling, typos, grammar, duplicated words
docs: dt: fix grammar and spelling
of: base: Add of_get_next_child_with_prefix() stub
dt-bindings: trivial-devices: Add compatible string synaptics,synaptics_i2c
dt-bindings: soc: mediatek: pwrap: Add power-domains property
dt-bindings: pinctrl: mt65xx: Allow gpio-line-names
dt-bindings: media: Convert MediaTek mt8173-vpu bindings to DT schema
dt-bindings: arm: mediatek: Support mt8183-audiosys variant
dt-bindings: mailbox: mediatek,gce-mailbox: Make clock-names optional
dt-bindings: regulator: mediatek,mt6331: Add missing compatible
dt-bindings: regulator: mediatek,mt6331: Fix various regulator names
dt-bindings: regulator: mediatek,mt6332-regulator: Add missing compatible
dt-bindings: pinctrl: mediatek,mt7622-pinctrl: Add missing base reg
dt-bindings: pinctrl: mediatek,mt7622-pinctrl: Add missing pwm_ch7_2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These are mostly thermal driver updates, including new thermal drivers
for Renesas RZ/G3S and Renesas RZ/G3E SoCs, a new power slider
platform feature support in the Intel int340x thermal driver, a new
Tegra114- specific SOCTHERM driver and more.
There is also a Step-wise thermal governor update allowing it to start
reducing cooling somewhat earlier if the temperature of the given
thermal zone is falling down and a thermal testing code cleanup.
Specifics:
- Add new thermal driver for the Renesas RZ/G3S SoC (Claudiu Beznea)
- Add new thermal driver for the Renesas RZ/G3E SoC (John Madieu)
- Add support for new platform power slider feature to the Intel
int340x driver (Srinivas Pandruvada).
- Add new Tegra114-specific SOCTHERM driver and document Tegra114
SOCTHERM Thermal Management System in DT bindings (Svyatoslav
Ryhel)
- Add temperature sensor channel to thermal-generic-adc (Svyatoslav
Ryhel)
- Add support for per-SoC default trim values to the Renesas
rcar_gen3 thermal driver, use it for adding R-Car V4H default trim
values, fix a comment typo in that driver and document Gen4 support
in its Kconfig entry (Marek Vasut)
- Fix mapping SoCs to generic Gen4 entry in the Renesas rcar_gen3
thermal driver (Wolfram Sang)
- Document the TSU unit in the r9a08g045-tsu and r9a09g047-tsu DT
bindings (Claudiu Beznea, John Madieu)
- Make LMH select QCOM_SCM and add missing IRQ includes to the
qcom/lmh thermal driver (Dmitry Baryshkov)
- Fix incorrect error message in the qcom/lmh thermal driver (Sumeet
Pawnikar)
- Add QCS615 compatible to tsens thermal DT bindings (Gaurav Kohli)
- Document the Glymur temperature sensor in qcom-tsens thermal DT
bindings (Manaf Meethalavalappu Pallikunhi)
- Make k3_j72xx_bandgap thermal driver register the thermal sensor
with hwmon (Michael Walle)
- Tighten GRF requirements in the rockchip thermal DT bindings,
silence a GRF warning in the rockchip thermal driver and unify
struct rockchip_tsadc_chip format in it (Sebastian Reichel)
- Update the Step-wise thermal governor to allow it to reduce the
cooling level earlier if thermal zone temperature is dropping and
clean it up (Rafael Wysocki)
- Clean up the thermal testing code (Rafael Wysocki)
- Assorted cleanups of thermal drivers (Jiapeng Chong, Salah Triki,
Osama Abdelkader)"
* tag 'thermal-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (37 commits)
thermal/drivers/renesas/rzg3e: Fix add thermal driver for the Renesas RZ/G3E SoC
dt-bindings: thermal: qcom-tsens: Document the Glymur temperature Sensor
thermal/drivers/renesas/rzg3e: Add thermal driver for the Renesas RZ/G3E SoC
dt-bindings: thermal: r9a09g047-tsu: Document the TSU unit
thermal/drivers/thermal-generic-adc: Add temperature sensor channel
dt-bindings: thermal: rockchip: Tighten grf requirements
thermal/drivers/rockchip: Shut up GRF warning
thermal/drivers/rockchip: Unify struct rockchip_tsadc_chip format
thermal/drivers/renesas/rzg3s: Add thermal driver for the Renesas RZ/G3S SoC
dt-bindings: thermal: r9a08g045-tsu: Document the TSU unit
thermal/drivers/k3_j72xx_bandgap: Register sensors with hwmon
thermal/drivers/rcar_gen3: Fix mapping SoCs to generic Gen4 entry
thermal/drivers/tegra: Add Tegra114 specific SOCTHERM driver
dt-bindings: thermal: add Tegra114 soctherm header
thermal/drivers/tegra/soctherm-fuse: Prepare calibration for Tegra114 support
dt-bindings: thermal: Document Tegra114 SOCTHERM Thermal Management System
thermal/drivers/rcar_gen3: Document Gen4 support in Kconfig entry
thermal/drivers/rcar_gen3: Fix comment typo
drivers/thermal/qcom/lmh: Fix incorrect error message
thermal/drivers/qcom/lmh: Add missing IRQ includes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include an ACPICA update (upstream revision 20250807 with a few
fixes on top), fixes and cleanups of the ACPI processor driver, fixes
and cleanups of the ACPI properties management code, one more ACPI IRQ
resource management quirk, one more ACPI backlight quirk, an ACPI
device enumeration quirk related to _DEP, a power resource quirk
related to WWAN modem for HP EliteBook 855 G7, ACPI SPCR table parser
extensions, an ACPI APEI EINJ driver update allowing it to handle more
address types, and several assorted cleanups of ACPI drivers and PNP
code.
Specifics:
- Add SoundWire File Table (SWFT) signature to ACPICA (Maciej
Strozek)
- Rearrange local variable definition involving #ifdef in ACPICA to
avoid using uninitialized variables (Zhe Qiao)
- Allow ACPICA to skip Global Lock initialization (Huacai Chen)
- Apply ACPI_NONSTRING in more places in ACPICA and fix two
regressions related to incorrect ACPI_NONSTRING usage (Ahmed Salem)
- Fix printing CDAT table header when dissasebling CDAT AML (Ahmed
Salem)
- Use acpi_ds_clear_operands() in acpi_ds_call_control_method() in
ACPICA (Hans de Goede)
- Update dsmethod.c in ACPICA to address unused variable warning
(Saket Dumbre)
- Print error messages in ACPICA for too few or too many control
method arguments (Saket Dumbre)
- Update ACPICA version to 20250807 (Saket Dumbre)
- Fix largest possible resource descriptor index in ACPICA (Dmitry
Antipov)
- Add Back-Invalidate restriction to CXL Window for CEDT in ACPICA
(Davidlohr Bueso)
- Add the package type to acceptable Arg3 types for _DSM in ACPICA
because ACPI_TYPE_ANY does not cover it (Saket Dumbre)
- Fix return values in ap_is_valid_checksum() in the acpidump utility
in ACPICA (Kaushlendra Kumar)
- Add Intel CVS ACPI HIDs to acpi_ignore_dep_ids[] so it is not
regarded as real dependency (Hans de Goede)
- Use ACPI_FREE() for freeing an ACPI object in description_show() in
the ACPI sysfs-related code (Kaushlendra Kumar)
- Fix memory leak in the ACPI processor idle driver registration
error code path and optimize ACPI idle driver registration (Huisong
Li, Rafael Wysocki)
- Add module import namespace to the ACPI processor idle driver
(Rafael Wysocki)
- Eliminate static variable flat_state_cnt from the ACPI processor
idle driver (Rafael Wysocki)
- Release cpufreq policy references using __free() in the ACPI
processor thremal driver (Zihuan Zhang)
- Remove unused empty stubs of some functions and rearrange function
declarations in a header file in the ACPI processor driver (Huisong
Li)
- Redefine two functions as void in the ACPI processor driver (Rafael
Wysocki)
- Stop exposing global variable acpi_idle_driver in the ACPI
processor driver (Huisong Li)
- Fix ACPI buffer properties extraction for data-only subnodes
represented as _DSD-equivalent packages (Rafael Wysocki)
- Fix handling of ACPI data-only subnodes represented as
_DSD-equivalent packages in the case when they are embedded in
larger _DSD-equivalent packages and clean up
acpi_nondev_subnode_extract() (Rafael Wysocki)
- Skip ACPI IRQ override on ASUS Vivobook Pro N6506CU (Sam van
Kampen)
- Add power resource init function and use it for introducing an HP
EliteBook 855 G7 WWAN modem power resource quirk (Maciej Szmigiero)
- Add support for DBG2 RISC-V SBI port subtype and Precise Baud Rate
field to the ACPI SPCR table parser (Chen Pei)
- Eliminate a dummy local variable from the ACPI thermal driver
(Rafael Wysocki)
- Fold two simple functions into their only caller in the ACPI fan
driver (Rafael Wysocki)
- Force native backlight on Lenovo 82K8 in the ACPI backlight (video)
driver (Mario Limonciello)
- Add missing sysfs_remove_group() for ACPI_TAD_RT (Daniel Tang)
- Skip PRM handlers with NULL handler_address or NULL VA in the ACPI
PRM driver (Shang song)
- Remove redundant assignments in erst_dbg_{ioctl|write}() in the
ACPI APEI driver (Thorsten Blum)
- Allow the ACPI APEI EINJ to handle more types of addresses than
just MMIO (Jiaqi Yan)
- Use str_low_high() helper in two places in the ACPI code (Chelsy
Ratnawat)
- Use str_plural() to simplify the PNP code (Xichao Zhao)
- Fix signedness issues in read/write helpers in the ACPI AML
debugger interface (Amir Mohammad)"
* tag 'acpi-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (50 commits)
ACPI: debug: fix signedness issues in read/write helpers
ACPI: processor: Do not expose global variable acpi_idle_driver
ACPI: SPCR: Support Precise Baud Rate field
ACPI: processor: idle: Redefine two functions as void
ACPI: processor: Update cpuidle driver check in __acpi_processor_start()
ACPI: processor: idle: Rearrange declarations in header file
ACPI: processor: Remove unused empty stubs of some functions
ACPI: property: Adjust failure handling in acpi_nondev_subnode_extract()
ACPI: property: Do not pass NULL handles to acpi_attach_data()
ACPI: property: Add code comments explaining what is going on
ACPI: property: Disregard references in data-only subnode lists
ACPI: property: Fix buffer properties extraction for subnodes
ACPI: SPCR: Add support for DBG2 RISC-V SBI port subtype
ACPI: APEI: EINJ: Allow more types of addresses except MMIO
ACPI: APEI: Remove redundant assignments in erst_dbg_{ioctl|write}()
ACPICA: acpidump: fix return values in ap_is_valid_checksum()
ACPICA: ACPI_TYPE_ANY does not include the package type
ACPICA: CEDT: Add Back-Invalidate restriction to CXL Window
ACPICA: Fix largest possible resource descriptor index
ACPICA: Update version to 20250807
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of these are cpufreq changes, which has been a recurring
pattern for a few recent cycles.
Those changes include new hardware support (AN7583 SoC support in the
airoha cpufreq driver, ipq5424 support in the qcom-nvmem cpufreq
driver, MT8196 support in the mediatek cpufreq driver, AM62D2 support
in the ti cpufreq driver), DT bindings and Rust code updates, cleanups
of the core and governors, and multiple driver fixes and cleanups.
Beyond that, there are hibernation fixes (some remaining 6.16 cycle
fallout and an issue related to hybrid suspend in the amdgpu driver),
cleanups of the PM core code, runtime PM documentation update, cpuidle
and power capping cleanups, and tooling updates.
Specifics:
- Rearrange variable declarations involving __free() in the cpufreq
core and intel_pstate driver to follow common coding style (Rafael
Wysocki)
- Fix object lifecycle issue in update_qos_request(), rearrange freq
QoS updates using __free(), and adjust frequency percentage
computations in the intel_pstate driver (Rafael Wysocki)
- Update intel_pstate to allow it to enable HWP without EPP if the
new DEC (Dynamic Efficiency Control) HW feature is enabled (Rafael
Wysocki)
- Use on_each_cpu_mask() in drv_write() in the ACPI cpufreq driver to
simplify the code (Rafael Wysocki)
- Use likely() optimization in intel_pstate_sample() (Yaxiong Tian)
- Remove dead EPB-related code from intel_pstate (Srinivas
Pandruvada)
- Use scope-based cleanup for cpufreq policy references in multiple
cpufreq drivers (Zihuan Zhang)
- Avoid calling get_governor() for the first policy in the cpufreq
core to simplify the initial policy path (Zihuan Zhang)
- Clean up the cpufreq core in multiple places (Zihuan Zhang)
- Use int type to store negative error codes in the cpufreq core and
update the speedstep-lib to use int for error codes (Qianfeng Rong)
- Update the efficient idle check for Intel extended Families in the
ondemand cpufreq governor (Sohil Mehta)
- Replace sscanf() with kstrtouint() in the conservative cpufreq
governor (Kaushlendra Kumar)
- Rename CpumaskVar::as[_mut]_ref to from_raw[_mut] in the cpumask
Rust code and mark CpumaskVar as transparent (Alice Ryhl, Baptiste
Lepers)
- Update ARef and AlwaysRefCounted imports from sync::aref in the OPP
Rust code (Shankari Anand)
- Add support for AN7583 SoC to the airoha cpufreq driver (Christian
Marangi)
- Enable cpufreq for ipq5424 in the qcom-nvmem cpufreq driver (Md
Sadre Alam)
- Add support for MT8196 to the mediatek-hw cpufreq driver, refactor
that driver and add mediatek,mt8196-cpufreq-hw DT binding (Nicolas
Frattaroli)
- Avoid redundant conditions in the mediatek cpufreq driver (Liao
Yuanhong)
- Add support for AM62D2 to the ti cpufreq driver and blocklist
ti,am62d2 SoC in dt-platdev (Paresh Bhagat)
- Support more speed grades on AM62Px SoC in the ti cpufreq driver,
allow all silicon revisions to support OPPs in it, and fix
supported hardware for 1GHz OPP (Judith Mendez)
- Add QCS615 compatible to DT bindings for cpufreq-qcom-hw (Taniya
Das)
- Minor assorted updates of the scmi, longhaul, CPPC, and armada-37xx
cpufreq drivers (Akhilesh Patil, BowenYu, Dennis Beier, and Florian
Fainelli)
- Remove outdated cpufreq-dt.txt (Frank Li)
- Fix python gnuplot package names in the amd_pstate_tracer utility
(Kuan-Wei Chiu)
- Saravana Kannan will maintain the virtual-cpufreq driver (Saravana
Kannan)
- Prevent CPU capacity updates after registering a perf domain from
failing on a first CPU that is not present (Christian Loehle)
- Add support for the cases in which frequency alone is not
sufficient to uniquely identify an OPP (Krishna Chaitanya Chundru)
- Use to_result() for OPP error handling in Rust (Onur Özkan)
- Add support for LPDDR5 on Rockhip RK3588 SoC to rockchip-dfi
devfreq driver (Nicolas Frattaroli)
- Fix an issue where DDR cycle counts on RK3588/RK3528 with LPDDR4(X)
are reported as half by adding a cycle multiplier to the DFI driver
in rockchip-dfi devfreq-event driver (Nicolas Frattaroli)
- Fix missing error pointer dereference check of regulator instance
in the mtk-cci devfreq driver probe and remove a redundant
condition from an if () statement in that driver (Dan Carpenter,
Liao Yuanhong)
- Fail cpuidle device registration if there is one already to avoid
sysfs-related issues (Rafael Wysocki)
- Use sysfs_emit()/sysfs_emit_at() instead of sprintf()/scnprintf()
in cpuidle (Vivek Yadav)
- Fix device and OF node leaks at probe in the qcom-spm cpuidle
driver and drop unnecessary initialisations from it (Johan Hovold)
- Remove unnecessary address-of operators from the intel_idle cpuidle
driver (Kaushlendra Kumar)
- Rearrange main loop in menu_select() to make the code in that
funtion easier to follow (Rafael Wysocki)
- Convert values in microseconds to ktime using us_to_ktime() where
applicable in the intel_idle power capping driver (Xichao Zhao)
- Annotate loops walking device links in the power management core
code as _srcu and add macros for walking device links to reduce the
likelihood of coding mistakes related to them (Rafael Wysocki)
- Document time units for *_time functions in the runtime PM API
(Brian Norris)
- Clear power.must_resume in noirq suspend error path to avoid
resuming a dependant device under a suspended parent or supplier
(Rafael Wysocki)
- Fix GFP mask handling during hybrid suspend and make the amdgpu
driver handle hybrid suspend correctly (Mario Limonciello, Rafael
Wysocki)
- Fix GFP mask handling after aborted hibernation in platform mode
and combine exit paths in power_down() to avoid code duplication
(Rafael Wysocki)
- Use vmalloc_array() and vcalloc() in the hibernation core to avoid
open-coded size computations (Qianfeng Rong)
- Fix typo in hibernation core code comment (Li Jun)
- Call pm_wakeup_clear() in the same place where other functions that
do bookkeeping prior to suspend_prepare() are called (Samuel Wu)
- Fix and clean up the x86_energy_perf_policy utility and update its
documentation (Len Brown, Kaushlendra Kumar)
- Fix incorrect sorting of PMT telemetry in turbostat (Kaushlendra
Kumar)
- Fix incorrect size in cpuidle_state_disable() and the error return
value of cpupower_write_sysfs() in cpupower (Kaushlendra Kumar)"
* tag 'pm-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
PM: hibernate: Combine return paths in power_down()
PM: hibernate: Restrict GFP mask in power_down()
PM: hibernate: Fix pm_hibernation_mode_is_suspend() build breakage
PM: runtime: Documentation: ABI: Document time units for *_time
tools/power x86_energy_perf_policy.8: Emphasize preference for SW interfaces
tools/power x86_energy_perf_policy: Add make snapshot target
tools/power x86_energy_perf_policy: Prefer driver HWP limits
tools/power x86_energy_perf_policy: EPB access is only via sysfs
tools/power x86_energy_perf_policy: Prepare for MSR/sysfs refactoring
tools/power x86_energy_perf_policy: Enhance HWP enable
tools/power x86_energy_perf_policy: Enhance HWP enabled check
tools/power x86_energy_perf_policy: Fix incorrect fopen mode usage
tools/power turbostat: Fix incorrect sorting of PMT telemetry
drm/amd: Fix hybrid sleep
PM: hibernate: Add pm_hibernation_mode_is_suspend()
PM: hibernate: Fix hybrid-sleep
tools/cpupower: Fix incorrect size in cpuidle_state_disable()
tools/power/x86/amd_pstate_tracer: Fix python gnuplot package names
cpufreq: Replace pointer subtraction with iteration macro
cpuidle: Fail cpuidle device registration if there is one already
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"New driver:
- Analog Devices I3C Controller
Subsystem:
- fix big-endian FIFO transfers
- fix default I2C adapter timeout value
Drivers:
- dw: shutdown support
- mipi-i3c-hci: Intel Wildcat Lake-U support, IOMMU support
- renesas: RZ/V2H(P) and RZ/V2N support"
* tag 'i3c/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux: (22 commits)
i3c: fix big-endian FIFO transfers
i3c: master: adi: fix number of bytes written to fifo
i3c: Remove superfluous FIXME
i3c: master: adi: fix header location
i3c: dw: Add shutdown support to dw_i3c_master driver
i3c: renesas: Simplify return statement in 'renesas_i3c_daa'
dt-bindings: i3c: renesas,i3c: Add RZ/V2H(P) and RZ/V2N support
i3c: master: svc: Recycle unused IBI slot
i3c: master: svc: Use manual response for IBI events
i3c: master: Add driver for Analog Devices I3C Controller IP
dt-bindings: i3c: Add adi-i3c-master
i3c: Fix default I2C adapter timeout value
i3c: mipi-i3c-hci: Convert remaining DBG() prints to dev_dbg()
i3c: mipi-i3c-hci: Remove function enter DBG() printouts
i3c: mipi-i3c-hci: Uniform ring number printouts
i3c: mipi-i3c-hci: Remove nonexistent ring interrupt
i3c: mipi-i3c-hci: Change interrupt status prints to dev_dbg()
i3c: mipi-i3c-hci: Use own DMA bounce buffer management for I2C transfers
i3c: mipi-i3c-hci: Use physical device pointer with DMA API
i3c: mipi-i3c-hci: Use core helpers for DMA mapping and bounce buffering
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Mostly DT bindings additions this time because Andi was super busy and
I also could only partly cover it.
- new ids for qcom-cci, mt65xx, exynos5, apple, tegra20, k1, i801
- drop support for already removed S3C2410
- introduce and use fwnode_for_each_child_node_scoped()
- mmt65xx: improve write-then-read transactions
- k1: various fixes around bus errors and resets
- usual share of cleanups, minor improvements, PM fixes...
at24 updates:
- add the compatible for Giantec GT24C256C to the device-tree
bindings"
* tag 'i2c-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (33 commits)
i2c: i801: Add support for Intel Wildcat Lake-U
dt-bindings: i2c: i2c-mt65xx: Add MediaTek MT8196/6991 compatibles
i2c: designware: Add disabling clocks when probe fails
i2c: designware: Fix clock issue when PM is disabled
i2c: busses: Fix some spelling errors
i2c: mux: Simplify boolean assignment in i2c_mux_alloc
i2c: designware: use dev_err_probe() when probing platform device
i2c: designware: convert to dev_err_probe() on request IRQ error
i2c: spacemit: ensure SDA is released after bus reset
i2c: spacemit: check SDA instead of SCL after bus reset
i2c: spacemit: disable SDA glitch fix to avoid restart delay
i2c: spacemit: remove stop function to avoid bus error
i2c: spacemit: ensure bus release check runs when wait_bus_idle() fails
i2c: mediatek: fix potential incorrect use of I2C_MASTER_WRRD
i2c: boardinfo: Annotate code used in init phase only
dt-bindings: i2c: i2c-mt65xx: Document MediaTek MT6878 I2C
dt-bindings: i2c: samsung,s3c2410-i2c: Drop S3C2410
i2c: s3c2410: Drop S3C2410 OF support
dt-bindings: i2c: spacemit,k1-i2c: Minor whitespace cleanup in example
dt-bindings: i2c: exynos5: add samsung,exynos8890-hsi2c compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have GPIO awareness in the pin control core and an interesting
AAEON driver.
Core changes:
- Allow pins to be identified/marked as GPIO mode with a special
callback.
The pin controller core is now "aware" if a pin is in GPIO mode if
the callback is implemented in the driver, and can thus be marked
as "strict", i.e. disallowing simultaneous use of a line as GPIO
and another function such as I2C.
This is enabled in the Qualcomm TLMM driver and also implemeted
from day 1 in the new Broadcom STB driver
- Rename the pin config option PIN_CONFIG_OUTPUT to PIN_CONFIG_LEVEL
to better describe what the config is doing, as well as making it
more intuitive what shall be returned when reading this property
New drivers:
- Qualcomm SDM660 LPASS LPI TLMM pin controller subdriver
- Qualcomm Glymur family pin controller driver
- Broadcom STB family pin controller driver
- Tegra186 pin controller driver
- AAEON UP pin controller support.
This is some special pin controller that works as an external
advanced line MUX and amplifier for signals from an Intel SoC. A
cooperative effort with the GPIO maintainer was needed to reach a
solution where we reuse code from the GPIO aggregator/forwarder
driver
- Renesas RZ/T2H and RZ/N2H pin controller support
- Axis ARTPEC-8 subdriver for the Samsung pin controller driver
Improvements:
- Output enable (OEN) support in the Renesas RZG2L driver
- Properly support bias pull up/down in the pinctrl-single driver
- Move over all GPIO portions using generic MMIO GPIO to the new
generic GPIO chip management which has a nice and separate API
- Proper DT bindings for some older Broadcom SoCs
- External GPIO (EGPIO) support in the Qualcomm SM8250
Deleted code:
- Dropped the now unused Samsung S3C24xx drivers"
* tag 'pinctrl-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: use more common syntax for compound literals
pinctrl: Simplify printks with pOF format
pinctrl: qcom: Add SDM660 LPASS LPI TLMM
dt-bindings: pinctrl: qcom: Add SDM660 LPI pinctrl
pinctrl: qcom: lpass-lpi: Add ability to use custom pin offsets
pinctrl: qcom: Add glymur pinctrl driver
dt-bindings: pinctrl: qcom: Add Glymur pinctrl
pinctrl: qcom: sm8250: Add egpio support
pinctrl: generic: rename PIN_CONFIG_OUTPUT to LEVEL
pinctrl: keembay: fix double free in keembay_build_functions()
pinctrl: spacemit: fix typo in PRI_TDI pin name
pinctrl: eswin: Fix regulator error check and Kconfig dependency
pinctrl: bcm: Add STB family pin controller driver
dt-bindings: pinctrl: Add support for Broadcom STB pin controller
pinctrl: qcom: make the pinmuxing strict
pinctrl: qcom: mark the `gpio` and `egpio` pins function as non-strict functions
pinctrl: qcom: add infrastructure for marking pin functions as GPIOs
pinctrl: allow to mark pin functions as requestable GPIOs
pinctrl: qcom: use generic pin function helpers
pinctrl: make struct pinfunction a pointer in struct function_desc
...
|
|
Pull IPMI updates from Corey Minyard:
"Bug fixes and enhancements for IPMI
This fixes a number of small bugs, but has some more major changes:
- Loongson-2K BMC support is added. This is an MFD device and is
dependent on the changes coming from that tree.
The way the driver handles BMCs that have become non-functional has
been completely redone. A number of changes in the past have
attempted to handle various issues around this, but nothing has
been very good. After working with some people on this, the code
has been reworked to disable the driver and fail all pending
operations if the BMC becomes non functional. It will retry the BMC
once a second to see if it's back up"
* tag 'for-linus-6.18-1' of https://github.com/cminyard/linux-ipmi:
ipmi: Add Loongson-2K BMC support
ipmi:si: Gracefully handle if the BMC is non-functional
ipmi: Rename "user_data" to "recv_msg" in an SMI message
ipmi: Allow an SMI sender to return an error
ipmi:si: Move flags get start to its own function
ipmi:si: Merge some if statements
ipmi: Set a timer for maintenance mode
ipmi: Add a maintenance mode sysfs file
ipmi: Disable sysfs access and requests in maintenance mode
ipmi: Differentiate between reset and firmware update in maintenance
dt-bindings: ipmi: aspeed,ast2400-kcs-bmc: Add missing "clocks" property
ipmi: Rework user message limit handling
Revert "ipmi: fix msg stack when IPMI is disconnected"
ipmi:msghandler:Change seq_lock to a mutex
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce adc-battery-helper for capacity estimation based on
simple ADC readings of battery voltage and current
- add new properties for battery internal resistance and state of
health
Power-supply drivers:
- ug3105_battery: convert to adc-battery-helper
- intel_dc_ti_battery: New driver for Intel Dollar Cove TI batteries
- rt9467-charger: add voltage and current ADC support
- sbs-charger: support multiple instances
- qcom_battmgr:
- add charge control support
- add support for state of health and internal resistance
- max77705_charger:
- big driver cleanup
- add support for setting charge current
- misc minor fixes and cleanups"
* tag 'for-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: qcom_battmgr: handle charging state change notifications
power: supply: max77705_charger: use REGMAP_IRQ_REG_LINE macro
power: supply: max77705_charger: rework interrupts
power: supply: max77705_charger: add writable properties
power: supply: max77705_charger: return error when config fails
power: supply: max77705_charger: use regfields for config registers
power: supply: max77705_charger: refactoring: rename charger to chg
mfd: max77705: max77705_charger: move active discharge setting to mfd parent
power: supply: max77976_charger: fix constant current reporting
power: supply: qcom_battmgr: Add charge control support
dt-bindings: soc: qcom,pmic-glink: Add charge limit nvmem properties
power: supply: qcom_battmgr: update compats for SM8550 and X1E80100
power: supply: qcom_battmgr: Add state_of_health property
power: supply: qcom_battmgr: Add resistance power supply property
power: supply: core: Add state_of_health power supply property
power: supply: core: Add resistance power supply property
power: supply: rx51: remove redundant condition checks
dt-bindings: power: supply: bq24190: document charge enable pin
dt-bindings: power: supply: bq27xxx: document optional interrupt
power: supply: intel_dc_ti_battery: Drop no longer relevant comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Takashi Sakamoto:
"This update includes the following changes:
- Removal of the deprecated debug parameter from firewire-ohci module
- Replacement of the module-local workqueue in 1394 OHCI PCI driver
with a companion IRQ thread
- Refactoring of bus management code
- Additional minor code cleanup
The existing tracepoints serve as an alternative to the removed debug
parameter. The use of IRQ thread is experimental, as it handles 1394
OHCI SelfIDComplete event only. It may be replaced in the future
releases with another approach; e.g. by providing workqueue from core
functionality"
* tag 'firewire-updates-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394: (43 commits)
firewire: core: fix undefined reference error in ARM EABI
Revert "firewire: core: disable bus management work temporarily during updating topology"
Revert "firewire: core: shrink critical section of fw_card spinlock in bm_work"
firewire: core: suppress overflow warning when computing jiffies from isochronous cycle
firewire: core: minor code refactoring to delete useless local variable
firewire: core; eliminate pick_me goto label
firewire: core: code refactoring to split contention procedure for bus manager
firewire: core: code refactoring for the case of generation mismatch
firewire: core: use switch statement to evaluate transaction result to CSR_BUS_MANAGER_ID
firewire: core: remove useless generation check
firewire: core: use struct_size and flex_array_size in ioctl_add_descriptor
firewire: core: shrink critical section of fw_card spinlock in bm_work
firewire: core: disable bus management work temporarily during updating topology
firewire: core: schedule bm_work item outside of spin lock
firewire: core: annotate fw_destroy_nodes with must-hold-lock
firewire: core: use spin lock specific to timer for split transaction
firewire: core: use spin lock specific to transaction
firewire: core: use spin lock specific to topology map
firewire: core: maintain phy packet receivers locally in cdev layer
firewire: core: use scoped_guard() to manage critical section to update topology
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"This round of updates contains a fair amount of new device support, a
couple of fixes and some refactoring. The most notable additions
include new drivers for Loongson's Security Engine, RNG and TPM, new
drivers for TI's TPS6594 Power Button and BQ257xx Charger ICs.
The rest of the set provides a return value check fix and a
refactoring to use a more modern GPIO API for the VEXPRESS sysreg
driver, the removal of a deprecated IRQ ACK function from the MC13xxx
RTC driver and a new DT binding for the aforementioned TI BQ257xx
charger.
New Support & Features:
- Add a suite of drivers for the Loongson Security Engine, including
the core controller, a Random Number Generator (RNG) and Trusted
Platform Module (TPM) support.
- Introduce support for the TI TPS6594 PMIC's power button, including
the input driver, MFD cell registration, and a system power-off
handler.
- Add comprehensive support for the TI BQ257xx series of charger ICs,
including the core MFD driver and a power supply driver for the
charger functionality.
Improvements & Fixes:
- Check the return value of devm_gpiochip_add_data() in the VEXPRESS
sysreg driver to prevent potential silent failures.
Cleanups & Refactoring:
- Add a MAINTAINERS entry for the new Loongson Security Engine
drivers.
- Convert the VEXPRESS sysreg driver to use the modern generic GPIO
chip API.
Removals:
- Remove the deprecated and unused mc13xxx_irq_ack() function from
the MC13xxx RTC, input and touchscreen drivers.
Device Tree Bindings Updates:
- Add device tree bindings for the TI BQ25703A charger"
* tag 'mfd-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: simple-mfd-i2c: Add compatible string for LX2160ARDB
mfd: simple-mfd-i2c: Keep compatible strings in alphabetical order
dt-bindings: mfd: twl: Add missing sub-nodes for TWL4030 & TWL603x
dt-bindings: watchdog: Add SMARC-sAM67 support
dt-bindings: mfd: tps6594: Allow gpio-line-names
mfd: intel-lpss: Add Intel Wildcat Lake LPSS PCI IDs
mfd: 88pm886: Add GPADC cell
mfd: vexpress-sysreg: Use more common syntax for compound literals
mfd: rz-mtu3: Fix MTU5 NFCR register offset
mfd: max77705: Setup the core driver as an interrupt controller
mfd: cs42l43: Remove IRQ masking in suspend
mfd: cs42l43: Move IRQ enable/disable to encompass force suspend
mfd: ls2kbmc: Add Loongson-2K BMC reset function support
mfd: ls2kbmc: Introduce Loongson-2K BMC core driver
mfd: bd71828, bd71815: Prepare for power-supply support
dt-bindings: mfd: aspeed: Add AST2700 SCU compatibles
dt-bindings: mfd: Convert aspeed,ast2400-p2a-ctrl to DT schema
dt-bindings: mfd: fsl,mc13xxx: Add buttons node
dt-bindings: mfd: fsl,mc13xxx: Convert txt to DT schema
mfd: macsmc: Add "apple,t8103-smc" compatible
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Improve RPMB frame handling code
- Add support for a new max-sd-hs-hz DT property to limit frequency
- Add support to manage regulator-under-voltage events
- Support regulator-under-voltage for eMMC to mitigate data
corruptions
- Add mmc_read_tuning() to allow a host to validate its tuning
sequence
- Add some helpers to align checks for CMD23 support
- Read the CCCR register for SDIO over SPI rather than the
unsupported CMD7
MMC host:
- Add COMPILE_TEST option for a couple of drivers
- Convert drivers to use the modern PM macros
- dw_mmc-exynos: Enable support for the Exynos8890 variant
- mmc_spi: Don't use crc ack during multiple block read
- renesas_sdhi: Enable 64-bit polling mode for R-Car gen3 and
RZ/G2L SoCs
- rtsx_usb: Add support for over-current-protection
- sdhci-cadence: Add support for multi-block read gap tuning
- sdhci-msm:
- Add support for tuning for SDR50 mode for SD cards
- Enable support for the Lemans variant
- sdhci-pci: Disable SD card clock before update for a few
Intel platforms
- sdhci-pxav3: Add support for UHS pinctrl settings
- tmio: Add 64-bit read/write support in polling mode
MEMSTICK:
- Convert to use timeouts to prevent indefinite waiting
- rtsx_usb: Add support for over-current-protection"
* tag 'mmc-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (77 commits)
dt-bindings: mmc: samsung,exynos-dw-mshc: add specific compatible for exynos8890
mmc: select REGMAP_MMIO with MMC_LOONGSON2
mmc: add COMPILE_TEST to multiple drivers
mmc: core: Improve RPMB frame handling code
mmc: core: Fix variable shadowing in mmc_route_rpmb_frames()
mmc: core: Parse and use the new max-sd-hs-hz DT property
dt-bindings: mmc: controller: Add max-sd-hs-hz property
mmc: sdhci-msm: Enable tuning for SDR50 mode for SD card
dt-bindings: mmc: sdhci-msm: Document the Lemans compatible
mmc: sh_mmcif: Remove dummy PM resume callback
dt-bindings: mmc: sdhci-pxa: Add minItems to pinctrl-names
mmc: sdio: Drop dev_pm_domain_detach() call
mmc: dw_mmc-rockchip: use modern PM macros
mmc: dw_mmc-pci: use modern PM macros
mmc: dw_mmc-k3: use modern PM macros
mmc: dw_mmc: exynos: use modern PM macros
mmc: via-sdmmc: use modern PM macros
mmc: sdhci-msm: use modern PM macros
mmc: mtk-sd: use modern PM macros
mmc: wmt-sdmmc: use modern PM macros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
- amlogic: Add support for S6/S7/S7D power-domains controller
- imx: Add support for i.MX91 power-domains
- marvell: Add support for PXA1908 power-domains
- mediatek:
- Add support for modem power sequence
- Add support for RTFF Hardware in MT8196/MT6991
- qcom: Align power-domain definitions for rpmpd
- rockchip: Default to use power-domain support
- thead: Create auxiliary device along with a corresponding reset
driver
- ti: Synchronize on/off state with HW-state for ti-sci power-domains
* tag 'pmdomain-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (25 commits)
pmdomain: thead: Fix error pointer vs NULL bug in th1520_pd_reboot_init()
pmdomain: thead: create auxiliary device for rebooting
driver: reset: th1520-aon: add driver for poweroff/reboot via AON FW
pmdomain: mediatek: airoha: convert from round_rate() to determine_rate()
pmdomain: rockchip: enable ROCKCHIP_PM_DOMAINS with ARCH_ROCKCHIP
pmdomain: marvell: Add PXA1908 power domains
dt-bindings: clock: marvell,pxa1908: Add syscon compatible to apmu
pmdomain: ti-sci: Set PD on/off state according to the HW state
pmdomain: amlogic: Add support for S6 S7 S7D power domains controller
dt-bindings: power: add Amlogic S6 S7 S7D power domains
pmdomain: mediatek: Convert all SoCs to new style regmap retrieval
pmdomain: mediatek: Add support for RTFF Hardware in MT8196/MT6991
pmdomain: mediatek: Add support for modem power sequences
pmdomain: mediatek: Move ctl sequences out of power_on/off functions
pmdomain: mediatek: Handle SoCs with inverted SRAM power-down bits
pmdomain: mediatek: Refactor bus protection regmaps retrieval
dt-bindings: power: mediatek: Document access-controllers property
pmdomain: remove unneeded 'fast_io' parameter in regmap_config
pmdomain: imx93-blk-ctrl: mask DSI and PXP PD domain register on i.MX91
pmdomain: imx93-blk-ctrl: use ARRAY_SIZE() instead of hardcode number
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"There's one big core change in this release, Jonas Gorski has
addressed the issues with multiple chip selects which makes things
more robust and stable. Otherwise there's quite a bit of driver work,
as well as some new drivers several existing drivers have had quite a
bit of work done on them.
Possibly the most interesting thing is the VirtIO driver, this is
apparently useful for some automotive applications which want to keep
as small and robust a host system as they can, moving less critical
functionality into guests.
- James Clark has done some substantial updates on the Freescale DSPI
driver, porting in code from the BSP and building onm top of that
to fix some bugs and increase performance
- Jonas Gorski has fixed the issues with handling multple chip
selects, making things more robust and scalable
- Support for higher performance modes in the NXP FSPI driver from
Haibo Chen
- Removal of the obsolete S3C2443 driver, the underlying SoC support
has been removed from the kernel
- Support for Amlogic AL113L2, Atmel SAMA7D65 and SAM9x7 and for
VirtIO controllers"
* tag 'spi-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (74 commits)
spi: ljca: Remove Wentong's e-mail address
spi: rename SPI_CS_CNT_MAX => SPI_DEVICE_CS_CNT_MAX
spi: reduce device chip select limit again
spi: don't check spi_controller::num_chipselect when parsing a dt device
spi: drop check for validity of device chip selects
spi: move unused device CS initialization to __spi_add_device()
spi: keep track of number of chipselects in spi_device
spi: fix return code when spi device has too many chipselects
SPI: Add virtio SPI driver
virtio-spi: Add virtio-spi.h
virtio: Add ID for virtio SPI
spi: rpc-if: Add resume support for RZ/G3E
spi: rpc-if: Drop deprecated SIMPLE_DEV_PM_OPS
spi: spi-qpic-snand: simplify clock handling by using devm_clk_get_enabled()
spi: spi-nxp-fspi: Add OCT-DTR mode support
spi: spi-nxp-fspi: add the support for sample data from DQS pad
spi: spi-nxp-fspi: Add the DDR LUT command support
spi: spi-nxp-fspi: set back to dll override mode when clock rate < 100MHz
spi: spi-nxp-fspi: extract function nxp_fspi_dll_override()
spi: atmel-quadspi: Add support for sama7d65 QSPI
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This is a very quiet release for regulator, almost all the changes are
new drivers but we do also have some improvements for the Rust
bindings.
- Additional APIs added to the Rust bindings
- Support for Maxim MAX77838, NXP PF0900 and PF5300, Richtek RT5133
and SpacemiT P1"
* tag 'regulator-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (28 commits)
regulator: dt-bindings: qcom,sdm845-refgen-regulator: document more platforms
regulator: Fix MAX77838 selection
regulator: spacemit: support SpacemiT P1 regulators
regulator: max77838: add max77838 regulator driver
dt-bindings: regulator: document max77838 pmic
rust: regulator: add devm_enable and devm_enable_optional
rust: regulator: remove Regulator<Dynamic>
regulator: dt-bindings: rpi-panel: Split 7" Raspberry Pi 720x1280 v2 binding
regulator: pf530x: Add a driver for the NXP PF5300 Regulator
regulator: dt-bindings: nxp,pf530x: Add NXP PF5300/PF5301/PF5302 PMICs
regulator: scmi: Use int type to store negative error codes
regulator: core: Remove redundant ternary operators
rust: regulator: use `to_result` for error handling
regulator: consumer.rst: document bulk operations
regulator: rt5133: Fix IS_ERR() vs NULL bug in rt5133_validate_vendor_info()
regulator: bd718x7: Use kcalloc() instead of kzalloc()
regulator: rt5133: Fix spelling mistake "regualtor" -> "regulator"
regulator: remove unneeded 'fast_io' parameter in regmap_config
regulator: rt5133: Add RT5133 PMIC regulator Support
regulator: dt-bindings: Add Richtek RT5133 Support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"There are two new drivers and support for more models in existing
ones.
The generic GPIO API has been reworked and all users converted
which allowed us to move the fields specific to the generic GPIO
implementation out of the high-level struct gpio_chip into its own
structure that wraps the gpio_chip.
Other than that, there's nothing too exciting. Mostly minor tweaks and
fixes all over the place, some refactoring and some small new features
in helper modules.
GPIO core:
- add support for sparse pin ranges to the glue between GPIO and
pinctrl
- use a common prefix across all GPIO descriptor flags for improved
namespacing
New drivers:
- add new GPIO driver for the Nuvoton NCT6694
- add new GPIO driver for MAX7360
Driver improvements:
- add support for Tegra 256 to the gpio-tegra186 driver
- add support for Loongson-2K0300 to the gpio-loongson-64bit driver
- refactor the gpio-aggregator module to expose its GPIO forwarder
API to other in-kernel users (to enable merging of a new pinctrl
driver that uses it)
- convert all remaining drivers to using the modernized generic GPIO
chip API and remove the old interface
- stop displaying global GPIO numbers in debugfs output of controller
drivers
- extend the gpio-regmap helper with a new config option and improve
its support for GPIO interrupts
- remove redundant fast_io parameter from regmap configs in GPIO
drivers that already use MMIO regmaps which imply it
- add support for a new model in gpio-mmio: ixp4xx expansion bus
- order includes alphabetically in a few drivers for better
readability
- use generic device properties where applicable
- use devm_mutex_init() where applicable
- extend build coverage of drivers by enabling more to be compiled
with COMPILE_TEST enabled
- allow building gpio-stmpe as a module
- use dev_err_probe() where it makes sense in drivers
Late driver fixes:
- fix setting GPIO direction to output in gpio-mpfs
Documentation:
- document the usage of software nodes with GPIO chips
Device-tree bindings:
- Add DT bindings documents for new hardware: Tegra256, MAX7360
- Document a new model in Loongson bindings: LS2K0300
- Document a new model using the generic GPIO binding: IXP4xx
- Convert the DT binding for fsl,mxs-pinctrl to YAML
- fix the schema ID in the "trivial" GPIO schema
- describe GPIO hogs in the generic GPIO binding"
* tag 'gpio-updates-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (122 commits)
gpio: mpfs: fix setting gpio direction to output
gpio: generic: move GPIO_GENERIC_ flags to the correct header
gpio: generic: rename BGPIOF_ flags to GPIO_GENERIC_
gpio: nomadik: fix the debugfs helper stub
MAINTAINERS: Add entry on MAX7360 driver
input: misc: Add support for MAX7360 rotary
input: keyboard: Add support for MAX7360 keypad
gpio: max7360: Add MAX7360 gpio support
gpio: regmap: Allow to provide init_valid_mask callback
gpio: regmap: Allow to allocate regmap-irq device
pwm: max7360: Add MAX7360 PWM support
pinctrl: Add MAX7360 pinctrl driver
mfd: Add max7360 support
dt-bindings: mfd: gpio: Add MAX7360
rtc: Add Nuvoton NCT6694 RTC support
hwmon: Add Nuvoton NCT6694 HWMON support
watchdog: Add Nuvoton NCT6694 WDT support
can: Add Nuvoton NCT6694 CANFD support
i2c: Add Nuvoton NCT6694 I2C support
gpio: Add Nuvoton NCT6694 GPIO support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm updates from Uwe Kleine-König:
"The core highlights for this cycle are:
- The pca9586 driver was converted to the waveform API
- Waveform drivers automatically provide a gpio chip to make PWMs
usable as GPIOs (The pca9586 driver did that in a driver specific
implementation before)
Otherwise it's the usual mix of fixes and device tree and driver
changes to support new hardware variants"
* tag 'pwm/for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux: (30 commits)
pwm: cros-ec: Avoid -Wflex-array-member-not-at-end warnings
dt-bindings: pwm: samsung: add exynos8890 compatible
dt-bindings: pwm: apple,s5l-fpwm: Add t6020-fpwm compatible
dt-bindings: pwm: nxp,lpc1850-sct-pwm: Minor whitespace cleanup in example
pwm: pca9586: Convert to waveform API
pwm: pca9685: Drop GPIO support
pwm: pca9685: Make use of register caching in regmap
pwm: pca9685: Use bulk write to atomicially update registers
pwm: pca9685: Don't disable hardware in .free()
pwm: Add the S32G support in the Freescale FTM driver
dt-bindings: pwm: fsl,vf610-ftm-pwm: Add compatible for s32g2 and s32g3
pwm: mediatek: Lock and cache clock rate
pwm: mediatek: Fix various issues in the .apply() callback
pwm: mediatek: Implement .get_state() callback
pwm: mediatek: Initialize clks when the hardware is enabled at probe time
pwm: mediatek: Rework parameters for clk helper function
pwm: mediatek: Introduce and use a few more register defines
pwm: mediatek: Simplify representation of channel offsets
pwm: tiecap: Document behaviour of hardware disable
pwm: Provide a gpio device for waveform drivers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Kontron SMARC-sAM67
- GPD device sensors
- MP29502
- MP2869, MP29608, MP29612 and MP29816 series
Added chip support to existing drivers:
- asus-ec-sensors:
Add B650E-I
Add PRIME Z270-A
Add Pro WS WRX90E-SAGE SE
Add ROG STRIX X670E-E GAMING WIFI
Add ROG STRIX X870-I GAMING WIFI
Add ROG STRIX X870E-E GAMING WIFI
Add ROG STRIX Z690-E GAMING WIFI
Add ROG STRIX Z790E GAMING WIFI II
Add STRIX B850-I GAMING WIFI
Add TUF GAMING X670E PLUS WIFI
Add X670E-I GAMING WIFI
Add Z790-I GAMING WIFI
- dell-smm: Add support for Dell OptiPlex 7040
- ina238: Major cleanup, and
Add support for INA700
Add support for INA780
- k10temp:
Add device ID for Strix Halo
Add support for AMD Family 1Ah-based models
- lenovo-ec-sensors: Update P8 supprt
- lm75: Add NXP P3T1750 support
- pmbus/adm1275: Add sq24905c support
- pmbus/isl68137: Add support for Renesas RAA228244 and RAA228246
- pmbus/mp5990: Add support for MP5998
- sht21: Add support for SHT20, SHT25
- sl28cpld: Add sa67mcu compatible
Other notable changes:
- core:
Handle locking internally
Introduce 64-bit energy attribute support
- cros_ec: Register into thermal framework, improve PWM control
- lm75: allow interrupt for ti,tmp75
- mlxreg-fan: Add support for new flavour of capability register
- sbtsi_temp: AMD CPU extended temperature range support
- sht21: Add devicetree support
Various other minor improvements and fixes"
* tag 'hwmon-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (86 commits)
dt-bindings: hwmon: (lm75) allow interrupt for ti,tmp75
hwmon: (mlxreg-fan) Add support for new flavour of capability register
hwmon: (mlxreg-fan) Separate methods of fan setting coming from different subsystems
hwmon: (cros_ec) register fans into thermal framework cooling devices
hwmon: (cros_ec) add PWM control over fans
platform/chrome: update pwm fan control host commands
hwmon: add SMARC-sAM67 support
dt-bindings: hwmon: sl28cpld: add sa67mcu compatible
hwmon: (asus-ec-sensors) add TUF GAMING X670E PLUS WIFI
hwmon: (dell-smm) Add support for Dell OptiPlex 7040
hwmon: (dell-smm) Add support for automatic fan mode
hwmon: (gpd-fan) complete Kconfig dependencies
hwmon: (asus-ec-sensors) increase timeout for locking ACPI mutex
hwmon: (asus-ec-sensors) add ROG STRIX X870E-E GAMING WIFI
hwmon: (dell-smm) Move clamping of fan speed out of i8k_set_fan()
hwmon: (dell-smm) Remove Dell Precision 490 custom config data
hwmon: (asus-ec-sensors) add ROG STRIX X670E-E GAMING WIFI
hwmon: (gpd-fan) Fix range check for pwm input
hwmon: (pmbus/mp5990) add support for MP5998
dt-bindings: trivial-devices: add mps,mp5998
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Tzung-Bi Shih:
"New:
- Add a new API cros_ec_device_registered() for checking if the
cros_ec_deivce is ready
Improvements:
- Use TRAILING_OVERLAP() to fix -Wflex-array-member-not-at-end
warning
- Defer probe until parent EC device is ready in cros_ec_keyb
Cleanups:
- Remove redundant and simplify code in cros_ec_chardev
- Centralize cros_ec_device allocation and initialization to remove
duplicate code"
* tag 'chrome-platform-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
Input: cros_ec_keyb - Defer probe until parent EC device is registered
platform/chrome: cros_ec: Add a flag to track registration state
platform/chrome: cros_ec: Separate initialization from cros_ec_register()
platform/chrome: Centralize common cros_ec_device initialization
platform/chrome: Centralize cros_ec_device allocation
platform/chrome: wilco_ec: Remove redundant semicolons
platform/chrome: cros_ec: Avoid -Wflex-array-member-not-at-end warning
platform/chrome: cros_ec_chardev: Decouple fops from struct cros_ec_dev
platform/chrome: cros_ec_chardev: Remove redundant struct field
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core updates from Danilo Krummrich:
"Auxiliary:
- Drop call to dev_pm_domain_detach() in auxiliary_bus_probe()
- Optimize logic of auxiliary_match_id()
Rust:
- Auxiliary:
- Use primitive C types from prelude
- DebugFs:
- Add debugfs support for simple read/write files and custom
callbacks through a File-type-based and directory-scope-based
API
- Sample driver code for the File-type-based API
- Sample module code for the directory-scope-based API
- I/O:
- Add io::poll module and implement Rust specific
read_poll_timeout() helper
- IRQ:
- Implement support for threaded and non-threaded device IRQs
based on (&Device<Bound>, IRQ number) tuples (IrqRequest)
- Provide &Device<Bound> cookie in IRQ handlers
- PCI:
- Support IRQ requests from IRQ vectors for a specific
pci::Device<Bound>
- Implement accessors for subsystem IDs, revision, devid and
resource start
- Provide dedicated pci::Vendor and pci::Class types for vendor
and class ID numbers
- Implement Display to print actual vendor and class names; Debug
to print the raw ID numbers
- Add pci::DeviceId::from_class_and_vendor() helper
- Use primitive C types from prelude
- Various minor inline and (safety) comment improvements
- Platform:
- Support IRQ requests from IRQ vectors for a specific
platform::Device<Bound>
- Nova:
- Use pci::DeviceId::from_class_and_vendor() to avoid probing
non-display/compute PCI functions
- Misc:
- Add helper for cpu_relax()
- Update ARef import from sync::aref
sysfs:
- Remove bin_attrs_new field from struct attribute_group
- Remove read_new() and write_new() from struct bin_attribute
Misc:
- Document potential race condition in get_dev_from_fwnode()
- Constify node_group argument in software node registration
functions
- Fix order of kernel-doc parameters in various functions
- Set power.no_pm flag for faux devices
- Set power.no_callbacks flag along with the power.no_pm flag
- Constify the pmu_bus bus type
- Minor spelling fixes"
* tag 'driver-core-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core: (43 commits)
rust: pci: display symbolic PCI vendor names
rust: pci: display symbolic PCI class names
rust: pci: fix incorrect platform reference in PCI driver probe doc comment
rust: pci: fix incorrect platform reference in PCI driver unbind doc comment
perf: make pmu_bus const
samples: rust: Add scoped debugfs sample driver
rust: debugfs: Add support for scoped directories
samples: rust: Add debugfs sample driver
rust: debugfs: Add support for callback-based files
rust: debugfs: Add support for writable files
rust: debugfs: Add support for read-only files
rust: debugfs: Add initial support for directories
driver core: auxiliary bus: Optimize logic of auxiliary_match_id()
driver core: auxiliary bus: Drop dev_pm_domain_detach() call
driver core: Fix order of the kernel-doc parameters
driver core: get_dev_from_fwnode(): document potential race
drivers: base: fix "publically"->"publicly"
driver core/PM: Set power.no_callbacks along with power.no_pm
driver core: faux: Set power.no_pm for faux devices
rust: pci: inline several tiny functions
...
|
|
synthetized => synthesized
definied => defined
sucess => success
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Drop CPUFREQ_ETERNAL that has no users any more along with all
references to it in the documentation.
No functional impact.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Jie Zhan <zhanjie9@hisilicon.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Qais Yousef <qyousef@layalina.io>
|
|
Instead of using CPUFREQ_ETERNAL for signaling an error condition
in cppc_get_transition_latency(), change the return value type of
that function to int and make it return a proper negative error
code on failures.
No intentional functional impact.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Jie Zhan <zhanjie9@hisilicon.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Qais Yousef <qyousef@layalina.io>
|
|
Commit a755d0e2d41b ("cpufreq: Honour transition_latency over
transition_delay_us") caused platforms where cpuinfo.transition_latency
is CPUFREQ_ETERNAL to get a very large transition latency whereas
previously it had been capped at 10 ms (and later at 2 ms).
This led to a user-observable regression between 6.6 and 6.12 as
described by Shawn:
"The dbs sampling_rate was 10000 us on 6.6 and suddently becomes
6442450 us (4294967295 / 1000 * 1.5) on 6.12 for these platforms
because the default transition delay was dropped [...].
It slows down dbs governor's reacting to CPU loading change
dramatically. Also, as transition_delay_us is used by schedutil
governor as rate_limit_us, it shows a negative impact on device
idle power consumption, because the device gets slightly less time
in the lowest OPP."
Evidently, the expectation of the drivers using CPUFREQ_ETERNAL as
cpuinfo.transition_latency was that it would be capped by the core,
but they may as well return a default transition latency value instead
of CPUFREQ_ETERNAL and the core need not do anything with it.
Accordingly, introduce CPUFREQ_DEFAULT_TRANSITION_LATENCY_NS and make
all of the drivers in question use it instead of CPUFREQ_ETERNAL. Also
update the related Rust binding.
Fixes: a755d0e2d41b ("cpufreq: Honour transition_latency over transition_delay_us")
Closes: https://lore.kernel.org/linux-pm/20250922125929.453444-1-shawnguo2@yeah.net/
Reported-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Jie Zhan <zhanjie9@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 6.6+ <stable@vger.kernel.org> # 6.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/2264949.irdbgypaU6@rafael.j.wysocki
[ rjw: Fix typo in new symbol name, drop redundant type cast from Rust binding ]
Tested-by: Shawn Guo <shawnguo@kernel.org> # with cpufreq-dt driver
Reviewed-by: Qais Yousef <qyousef@layalina.io>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Lacking the support of device specific mapping supported in virtio,
VDUSE must trick the DMA API in order to make virtio-vdpa transport
work. This is done by advertising vDPA device as dma device with a
VDUSE specific dma_ops even if it doesn't do DMA at all.
This will be fixed by this patch. Thanks to the new mapping operations
support by virtio and vDPA. VDUSE can simply switch to advertise its
specific mappings operations to virtio via virtio-vdpa then DMA API is
not needed for VDUSE any more and iova domain could be used as the
mapping token instead.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250924070045.10361-3-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
Virtio core allows the transport to provide device or transport
specific mapping functions. This patch adds this support to vDPA. We
can simply do this by allowing the vDPA parent to register a
virtio_map_ops.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250924070045.10361-2-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
Virtio core switches from DMA device to virtio_map, let's do that
as well for vDPA.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250821064641.5025-8-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
This patch introduces map operations for virtio device. Virtio used to
use DMA API which is not necessarily the case since some devices
doesn't do DMA. Instead of using tricks and abusing DMA API, let's
simply abstract the current mapping logic into a virtio specific
mapping operations. For the device or transport that doesn't do DMA,
they can implement their own mapping logic without the need to trick
DMA core. In this case the mapping metadata is opaque to the virtio
core that will be passed back to the transport or device specific map
operations. For other devices, DMA API will still be used, so map
token will still be the dma device to minimize the changeset and
performance impact.
The mapping operations are abstracted as a independent structure
instead of reusing virtio_config_ops. This allows the transport can
simply reuse the structure for lower layers like vDPA.
A set of new mapping helpers were introduced for the device that want
to do mapping by themselves.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250821064641.5025-7-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
Following patch will introduce the mapping operations for virtio
device. In order to achieve this, besides the dma device, virtio core
needs to support a transport or device specific mapping metadata as well.
So this patch introduces a union container of a dma device. The idea
is the allow the transport layer to pass device specific mapping
metadata which will be used as a parameter for the virtio mapping
operations. For the transport or device that is using DMA, dma device
is still being used.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250821064641.5025-5-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
Following patch will introduce virtio mapping function to avoid
abusing DMA API for device that doesn't do DMA. To ease the
introduction, this patch rename "dma" to "map" for the current dma
mapping helpers.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250821064641.5025-4-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
This patch constifies the virtqueue pointer for DMA helpers.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250821064641.5025-2-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
Add core support for ROHM BD718(15/28/78) PMIC's charger blocks.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20250821-bd71828-charger-v3-1-cc74ac4e0fb9@kemnade.info
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The only machine that still uses the old gpio number based interface
is the wlf_cragg_6410 board file. In order to remove the dependency
on the interfaces, add #ifdef blocks here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250808151822.536879-13-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Relying on other components to include those basic types is unreliable
and may cause compile errors like:
../include/linux/mfd/qnap-mcu.h:13:9: error: unknown type name ‘u32’
13 | u32 baud_rate;
| ^~~
../include/linux/mfd/qnap-mcu.h:17:9: error: unknown type name ‘bool’
17 | bool usb_led;
| ^~~~
So make sure, the types used in the header are available.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250804130726.3180806-2-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
'ib-mfd-gpio-hwmon-i2c-can-rtc-watchdog-6.18', 'ib-mfd-gpio-input-pinctrl-pwm-6.18', 'ib-mfd-input-6.18', 'ib-mfd-input-rtc-6.18' and 'ib-mfd-power-regulator-6.18' into ibs-for-mfd-merged
|
|
Cross-merge networking fixes after downstream PR (net-6.17-rc8).
Conflicts:
tools/testing/selftests/drivers/net/bonding/Makefile
87951b566446 selftests: bonding: add test for passive LACP mode
c2377f1763e9 selftests: bonding: add test for LACP actor port priority
Adjacent changes:
drivers/net/ethernet/cadence/macb.h
fca3dc859b20 net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf169e net: macb: Add TAPRIO traffic scheduling support
drivers/net/ethernet/cadence/macb_main.c
fca3dc859b20 net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf169e net: macb: Add TAPRIO traffic scheduling support
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit 7bd80ed89d72285515db673803b021469ba71ee8.
I should not have merged it to begin with due to pending review and
changes to be addressed.
Link: https://patch.msgid.link/c6f3af12df9b7998920a02027fc8893ce82afc4c.1759239721.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Implement atomic_flush, atomic_enable and atomic_disable of struct
drm_crtc_helper_funcs for vblank handling. Driver with no further
requirements can use these functions instead of adding their own.
Also simplifies the use of vblank timers.
The code has been adopted from vkms, which added the funtionality
in commit 3a0709928b17 ("drm/vkms: Add vblank events simulated by
hrtimers").
v3:
- mention vkms (Javier)
v2:
- fix docs
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20250916083816.30275-3-tzimmermann@suse.de
|
|
The vblank timer simulates a vblank interrupt for hardware without
support. Rate-limits the display update frequency.
DRM drivers for hardware without vblank support apply display updates
ASAP. A vblank event informs DRM clients of the completed update.
Userspace compositors immediately schedule the next update, which
creates significant load on virtualization outputs. Display updates
are usually fast on virtualization outputs, as their framebuffers are
in regular system memory and there's no hardware vblank interrupt to
throttle the update rate.
The vblank timer is a HR timer that signals the vblank in software.
It limits the update frequency of a DRM driver similar to a hardware
vblank interrupt. The timer is not synchronized to the actual vblank
interval of the display.
The code has been adopted from vkms, which added the funtionality
in commit 3a0709928b17 ("drm/vkms: Add vblank events simulated by
hrtimers").
The new implementation is part of the existing vblank support,
which sets up the timer automatically. Drivers only have to start
and cancel the vblank timer as part of enabling and disabling the
CRTC. The new vblank helper library provides callbacks for struct
drm_crtc_funcs.
The standard way for handling vblank is to call drm_crtc_handle_vblank().
Drivers that require additional processing, such as vkms, can init
handle_vblank_timeout in struct drm_crtc_helper_funcs to refer to
their timeout handler.
There's a possible deadlock between drm_crtc_handle_vblank() and
hrtimer_cancel(). [1] The implementation avoids to call hrtimer_cancel()
directly and instead signals to the timer function to not restart
itself.
v4:
- fix possible race condition between timeout and atomic commit (Michael)
v3:
- avoid deadlock when cancelling timer (Ville, Lyude)
v2:
- implement vblank timer entirely in vblank helpers
- downgrade overrun warning to debug
- fix docs
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/all/20250510094757.4174662-1-zengheng4@huawei.com/ # [1]
Link: https://lore.kernel.org/r/20250916083816.30275-2-tzimmermann@suse.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf updates from Alexei Starovoitov:
- Support pulling non-linear xdp data with bpf_xdp_pull_data() kfunc
(Amery Hung)
Applied as a stable branch in bpf-next and net-next trees.
- Support reading skb metadata via bpf_dynptr (Jakub Sitnicki)
Also a stable branch in bpf-next and net-next trees.
- Enforce expected_attach_type for tailcall compatibility (Daniel
Borkmann)
- Replace path-sensitive with path-insensitive live stack analysis in
the verifier (Eduard Zingerman)
This is a significant change in the verification logic. More details,
motivation, long term plans are in the cover letter/merge commit.
- Support signed BPF programs (KP Singh)
This is another major feature that took years to materialize.
Algorithm details are in the cover letter/marge commit
- Add support for may_goto instruction to s390 JIT (Ilya Leoshkevich)
- Add support for may_goto instruction to arm64 JIT (Puranjay Mohan)
- Fix USDT SIB argument handling in libbpf (Jiawei Zhao)
- Allow uprobe-bpf program to change context registers (Jiri Olsa)
- Support signed loads from BPF arena (Kumar Kartikeya Dwivedi and
Puranjay Mohan)
- Allow access to union arguments in tracing programs (Leon Hwang)
- Optimize rcu_read_lock() + migrate_disable() combination where it's
used in BPF subsystem (Menglong Dong)
- Introduce bpf_task_work_schedule*() kfuncs to schedule deferred
execution of BPF callback in the context of a specific task using the
kernel’s task_work infrastructure (Mykyta Yatsenko)
- Enforce RCU protection for KF_RCU_PROTECTED kfuncs (Kumar Kartikeya
Dwivedi)
- Add stress test for rqspinlock in NMI (Kumar Kartikeya Dwivedi)
- Improve the precision of tnum multiplier verifier operation
(Nandakumar Edamana)
- Use tnums to improve is_branch_taken() logic (Paul Chaignon)
- Add support for atomic operations in arena in riscv JIT (Pu Lehui)
- Report arena faults to BPF error stream (Puranjay Mohan)
- Search for tracefs at /sys/kernel/tracing first in bpftool (Quentin
Monnet)
- Add bpf_strcasecmp() kfunc (Rong Tao)
- Support lookup_and_delete_elem command in BPF_MAP_STACK_TRACE (Tao
Chen)
* tag 'bpf-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (197 commits)
libbpf: Replace AF_ALG with open coded SHA-256
selftests/bpf: Add stress test for rqspinlock in NMI
selftests/bpf: Add test case for different expected_attach_type
bpf: Enforce expected_attach_type for tailcall compatibility
bpftool: Remove duplicate string.h header
bpf: Remove duplicate crypto/sha2.h header
libbpf: Fix error when st-prefix_ops and ops from differ btf
selftests/bpf: Test changing packet data from kfunc
selftests/bpf: Add stacktrace map lookup_and_delete_elem test case
selftests/bpf: Refactor stacktrace_map case with skeleton
bpf: Add lookup_and_delete_elem for BPF_MAP_STACK_TRACE
selftests/bpf: Fix flaky bpf_cookie selftest
selftests/bpf: Test changing packet data from global functions with a kfunc
bpf: Emit struct bpf_xdp_sock type in vmlinux BTF
selftests/bpf: Task_work selftest cleanup fixes
MAINTAINERS: Delete inactive maintainers from AF_XDP
bpf: Mark kfuncs as __noclone
selftests/bpf: Add kprobe multi write ctx attach test
selftests/bpf: Add kprobe write ctx attach test
selftests/bpf: Add uprobe context ip register change test
...
|
|
At present VMBus driver is hinged off of CONFIG_HYPERV which entails
lot of builtin code and encompasses too much. It's not always clear
what depends on builtin hv code and what depends on VMBus. Setting
CONFIG_HYPERV as a module and fudging the Makefile to switch to builtin
adds even more confusion. VMBus is an independent module and should have
its own config option. Also, there are scenarios like baremetal dom0/root
where support is built in with CONFIG_HYPERV but without VMBus. Lastly,
there are more features coming down that use CONFIG_HYPERV and add more
dependencies on it.
So, create a fine grained HYPERV_VMBUS option and update Kconfigs for
dependency on VMBus.
Signed-off-by: Mukesh Rathor <mrathor@linux.microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull VDSO updates from Thomas Gleixner:
- Further consolidation of the VDSO infrastructure and the common data
store
- Simplification of the related Kconfig logic
- Improve the VDSO selftest suite
* tag 'timers-vdso-2025-09-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests: vDSO: Drop vdso_test_clock_getres
selftests: vDSO: vdso_test_abi: Add tests for clock_gettime64()
selftests: vDSO: vdso_test_abi: Test CPUTIME clocks
selftests: vDSO: vdso_test_abi: Use explicit indices for name array
selftests: vDSO: vdso_test_abi: Drop clock availability tests
selftests: vDSO: vdso_test_abi: Use ksft_finished()
selftests: vDSO: vdso_test_abi: Correctly skip whole test with missing vDSO
selftests: vDSO: Fix -Wunitialized in powerpc VDSO_CALL() wrapper
vdso: Add struct __kernel_old_timeval forward declaration to gettime.h
vdso: Gate VDSO_GETRANDOM behind HAVE_GENERIC_VDSO
vdso: Drop Kconfig GENERIC_VDSO_TIME_NS
vdso: Drop Kconfig GENERIC_VDSO_DATA_STORE
vdso: Drop kconfig GENERIC_COMPAT_VDSO
vdso: Drop kconfig GENERIC_VDSO_32
riscv: vdso: Untangle Kconfig logic
time: Build generic update_vsyscall() only with generic time vDSO
vdso/gettimeofday: Remove !CONFIG_TIME_NS stubs
vdso: Move ENABLE_COMPAT_VDSO from core to arm64
ARM: VDSO: Remove cntvct_ok global variable
vdso/datastore: Gate time data behind CONFIG_GENERIC_GETTIMEOFDAY
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource updates from Thomas Gleixner:
- Further preparations for modular clocksource/event drivers
- The usual device tree updates to support new chip variants and the
related changes to thise drivers
- Avoid a 64-bit division in the TEGRA186 driver, which caused a build
fail on 32-bit machines.
- Small fixes, improvements and cleanups all over the place
* tag 'timers-clocksource-2025-09-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
dt-bindings: timer: exynos4210-mct: Add compatible for ARTPEC-9 SoC
clocksource/drivers/sh_cmt: Split start/stop of clock source and events
clocksource/drivers/clps711x: Fix resource leaks in error paths
clocksource/drivers/arm_global_timer: Add auto-detection for initial prescaler values
clocksource/drivers/ingenic-sysost: Convert from round_rate() to determine_rate()
clocksource/drivers/timer-tegra186: Don't print superfluous errors
clocksource/drivers/timer-rtl-otto: Simplify documentation
clocksource/drivers/timer-rtl-otto: Do not interfere with interrupts
clocksource/drivers/timer-rtl-otto: Drop set_counter function
clocksource/drivers/timer-rtl-otto: Work around dying timers
clocksource/drivers/timer-ti-dm : Capture functionality for OMAP DM timer
clocksource/drivers/arm_arch_timer_mmio: Add MMIO clocksource
clocksource/drivers/arm_arch_timer_mmio: Switch over to standalone driver
clocksource/drivers/arm_arch_timer: Add standalone MMIO driver
ACPI: GTDT: Generate platform devices for MMIO timers
clocksource/drivers/nxp-pit: Add NXP Automotive s32g2 / s32g3 support
dt: bindings: fsl,vf610-pit: Add compatible for s32g2 and s32g3
clocksource/drivers/vf-pit: Rename the VF PIT to NXP PIT
clocksource/drivers/vf-pit: Unify the function name for irq ack
clocksource/drivers/vf-pit: Consolidate calls to pit_*_disable/enable
...
|
