| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For many years btrfs as been using a copy of may_create() in
fs/btrfs/ioctl.c:btrfs_may_create(). Everytime may_create() is updated we
need to update the btrfs copy, and this is a maintenance burden. Currently
there are minor differences between both because the btrfs side lacks
updates done in may_create().
Export may_create() so that btrfs can use it and with the less generic
name may_create_dentry().
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Link: https://patch.msgid.link/ce5174bca079f4cdcbb8dd145f0924feb1f227cd.1768307858.git.fdmanana@suse.com
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
For many years btrfs as been using a copy of may_delete() in
fs/btrfs/ioctl.c:btrfs_may_delete(). Everytime may_delete() is updated we
need to update the btrfs copy, and this is a maintenance burden. Currently
there are minor differences between both because the btrfs side lacks
updates done in may_delete().
Export may_delete() so that btrfs can use it and with the less generic
name may_delete_dentry(). While at it change the calls in vfs_rmdir() to
pass a boolean literal instead of 1 and 0 as the last argument since the
argument has a bool type.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Link: https://patch.msgid.link/e09128fd53f01b19d0a58f0e7d24739f79f47f6d.1768307858.git.fdmanana@suse.com
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
When Firmware First is enabled, BIOS handles errors first and then it
makes them available to the kernel via the Common Platform Error Record
(CPER) sections (UEFI 2.11 Appendix N.2.13). Linux parses the CPER
sections via one of two similar paths, either ELOG or GHES. The errors
managed by ELOG are signaled to the BIOS by the I/O Machine Check
Architecture (I/O MCA).
Currently, ELOG and GHES show some inconsistencies in how they report to
userspace via trace events.
Therefore, make the two mentioned paths act similarly by tracing the CPER
CXL Protocol Error Section.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
Link: https://patch.msgid.link/20260114101543.85926-6-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make a helper out of cxl_cper_post_prot_err() that checks the CXL agent
type and copy the CPER CXL protocol errors information to a work data
structure.
Export the new symbol for reuse by ELOG.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
[ rjw: Subject tweak ]
Link: https://patch.msgid.link/20260114101543.85926-5-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Move the CPER CXL protocol errors validity check out of
cxl_cper_post_prot_err() to new cxl_cper_sec_prot_err_valid() and limit
the serial number check only to CXL agents that are CXL devices (UEFI
v2.10, Appendix N.2.13).
Export the new symbol for reuse by ELOG.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Fabio M. De Francesco <fabio.m.de.francesco@linux.intel.com>
[ rjw: Subject tweak ]
Link: https://patch.msgid.link/20260114101543.85926-4-fabio.m.de.francesco@linux.intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ghes_notify_nmi() is called for every NMI and must check whether the NMI was
generated because an error was signalled by platform firmware.
This check is very expensive as for each registered GHES NMI source it reads
from the acpi generic address attached to this error source to get the physical
address of the acpi_hest_generic_status block. It then checks the "block_status"
to see if an error was logged.
The ACPI/APEI code must create virtual mappings for each of those physical
addresses, and tear them down afterwards. On an Icelake system this takes around
15,000 TSC cycles. Enough to disturb efforts to profile system performance.
If that were not bad enough, there are some atomic accesses in the code path
that will cause cache line bounces between CPUs. A problem that gets worse as
the core count increases.
But BIOS changes neither the acpi generic address nor the physical address of
the acpi_hest_generic_status block. So this walk can be done once when the NMI is
registered to save the virtual address (unmapping if the NMI is ever unregistered).
The "block_status" can be checked directly in the NMI handler. This can be done
without any atomic accesses.
Resulting time to check that there is not an error record is around 900 cycles.
Reported-by: Andi Kleen <andi.kleen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://patch.msgid.link/20260112032239.30023-2-xueshuai@linux.alibaba.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The logic at ghes_new() prevents allocating too large records, by
checking if they're bigger than GHES_ESTATUS_MAX_SIZE (currently, 64KB).
Yet, the allocation is done with the actual number of pages from the
CPER bios table location, which can be smaller.
Yet, a bad firmware could send data with a different size, which might
be bigger than the allocated memory, causing an OOPS:
Unable to handle kernel paging request at virtual address fff00000f9b40000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
Data abort info:
ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 52-bit VAs, pgdp=000000008ba16000
[fff00000f9b40000] pgd=180000013ffff403, p4d=180000013fffe403, pud=180000013f85b403, pmd=180000013f68d403, pte=0000000000000000
Internal error: Oops: 0000000096000007 [#1] SMP
Modules linked in:
CPU: 0 UID: 0 PID: 303 Comm: kworker/0:1 Not tainted 6.19.0-rc1-00002-gda407d200220 #34 PREEMPT
Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 02/02/2022
Workqueue: kacpi_notify acpi_os_execute_deferred
pstate: 214020c5 (nzCv daIF +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : hex_dump_to_buffer+0x30c/0x4a0
lr : hex_dump_to_buffer+0x328/0x4a0
sp : ffff800080e13880
x29: ffff800080e13880 x28: ffffac9aba86f6a8 x27: 0000000000000083
x26: fff00000f9b3fffc x25: 0000000000000004 x24: 0000000000000004
x23: ffff800080e13905 x22: 0000000000000010 x21: 0000000000000083
x20: 0000000000000001 x19: 0000000000000008 x18: 0000000000000010
x17: 0000000000000001 x16: 00000007c7f20fec x15: 0000000000000020
x14: 0000000000000008 x13: 0000000000081020 x12: 0000000000000008
x11: ffff800080e13905 x10: ffff800080e13988 x9 : 0000000000000000
x8 : 0000000000000000 x7 : 0000000000000001 x6 : 0000000000000020
x5 : 0000000000000030 x4 : 00000000fffffffe x3 : 0000000000000000
x2 : ffffac9aba78c1c8 x1 : ffffac9aba76d0a8 x0 : 0000000000000008
Call trace:
hex_dump_to_buffer+0x30c/0x4a0 (P)
print_hex_dump+0xac/0x170
cper_estatus_print_section+0x90c/0x968
cper_estatus_print+0xf0/0x158
__ghes_print_estatus+0xa0/0x148
ghes_proc+0x1bc/0x220
ghes_notify_hed+0x5c/0xb8
notifier_call_chain+0x78/0x148
blocking_notifier_call_chain+0x4c/0x80
acpi_hed_notify+0x28/0x40
acpi_ev_notify_dispatch+0x50/0x80
acpi_os_execute_deferred+0x24/0x48
process_one_work+0x15c/0x3b0
worker_thread+0x2d0/0x400
kthread+0x148/0x228
ret_from_fork+0x10/0x20
Code: 6b14033f 540001ad a94707e2 f100029f (b8747b44)
---[ end trace 0000000000000000 ]---
Prevent that by taking the actual allocated are into account when
checking for CPER length.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject tweaks ]
Link: https://patch.msgid.link/4e70310a816577fabf37d94ed36cde4ad62b1e0a.1767871950.git.mchehab+huawei@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There's a logic inside GHES/CPER to detect if the section_length
is too small, but it doesn't detect if it is too big.
Currently, if the firmware receives an ARM processor CPER record
stating that a section length is big, kernel will blindly trust
section_length, producing a very long dump. For instance, a 67
bytes record with ERR_INFO_NUM set 46198 and section length
set to 854918320 would dump a lot of data going a way past the
firmware memory-mapped area.
Fix it by adding a logic to prevent it to go past the buffer
if ERR_INFO_NUM is too big, making it report instead:
[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
[Hardware Error]: event severity: recoverable
[Hardware Error]: Error 0, type: recoverable
[Hardware Error]: section_type: ARM processor error
[Hardware Error]: MIDR: 0xff304b2f8476870a
[Hardware Error]: section length: 854918320, CPER size: 67
[Hardware Error]: section length is too big
[Hardware Error]: firmware-generated error record is incorrect
[Hardware Error]: ERR_INFO_NUM is 46198
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
[ rjw: Subject and changelog tweaks ]
Link: https://patch.msgid.link/41cd9f6b3ace3cdff7a5e864890849e4b1c58b63.1767871950.git.mchehab+huawei@kernel.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Write down the missing members definitions for struct export_operations,
using as a reference the commit messages that created the members.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Link: https://patch.msgid.link/20260112-tonyk-fs_uuid-v1-3-acc1889de772@igalia.com
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Adding a `@` before the function names make then recognizable as
kernel-docs, so they get correctly rendered in the documentation.
Even if they are already marked with `@` in the short one-line summary,
the kernel-docs will correctly favor the more detailed definition here.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Link: https://patch.msgid.link/20260112-tonyk-fs_uuid-v1-2-acc1889de772@igalia.com
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Without a space between %NAME_MAX and the plus sign, kernel-doc will
output ``NAME_MAX``+1, which scapes the last backtick and make Sphinx
format a much larger string as monospaced text.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Link: https://patch.msgid.link/20260112-tonyk-fs_uuid-v1-1-acc1889de772@igalia.com
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
commit 4ef4ac360101 ("device_cgroup: avoid access to ->i_rdev in the
common case in devcgroup_inode_permission()") reordered the checks in
devcgroup_inode_permission() to check the inode mode before checking
i_rdev, for better cache behavior.
However, the likely() annotation on the i_rdev check was not updated
to reflect the new code flow. Originally, when i_rdev was checked
first, likely(!inode->i_rdev) made sense because most inodes were(?)
regular files/directories, thus i_rdev == 0.
After the reorder, by the time we reach the i_rdev check, we have
already confirmed the inode IS a block or character device. Block and
character special files are precisely defined by having a device number
(i_rdev), so !inode->i_rdev is now the rare edge case, not the common
case.
Branch profiling confirmed this is 100% mispredicted:
correct incorrect % Function File Line
------- --------- - -------- ---- ----
0 2631904 100 devcgroup_inode_permission device_cgroup.h 24
Remove likely() to avoid giving the wrong hint to the CPU.
Fixes: 4ef4ac360101 ("device_cgroup: avoid access to ->i_rdev in the common case in devcgroup_inode_permission()")
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20260107-likely_device-v1-1-0c55f83a7e47@debian.org
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
It's useful to get filesystem-specific information using the
existing private field in the @iomap_iter passed to iomap_{begin,end}
for advanced usage for iomap buffered reads, which is much like the
current iomap DIO.
For example, EROFS needs it to:
- implement an efficient page cache sharing feature, since iomap
needs to apply to anon inode page cache but we'd like to get the
backing inode/fs instead, so filesystem-specific private data is
needed to keep such information;
- pass in both struct page * and void * for inline data to avoid
kmap_to_page() usage (which is bogus).
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20260109102856.598531-2-lihongbo22@huawei.com
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
It turns out that warning about which USB host controller is loaded
before another one doesn't really matter. All that really is needed is
the PCI softdep module loading logic, which has been present in the
kernel ever since commit 05c92da0c524 ("usb: ohci/uhci - add soft
dependencies on ehci_pci")
So remove the warning messages, they are not useful, not needed, and
only confuse people. As can be seen in the discussion at
https://lore.kernel.org/r/20251230080014.3934590-1-chenhuacai@loongson.cn
Cc: Huacai Chen <chenhuacai@loongson.cn>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/2026010739-diffuser-shelter-e31c@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for MIPI I3C Host Controllers with the Multi-Bus Instance
capability. These controllers can host multiple I3C buses (up to 15)
within a single hardware function (e.g., PCIe B/D/F), providing one
indepedent HCI register set and corresponding I3C bus controller logic
per bus.
A separate platform device will represent each instance, but it is
necessary to allow for shared resources.
Multi-bus instances share the same MMIO address space, but the ranges are
not guaranteed to be contiguous. To avoid overlapping mappings, pass
base_regs from the parent mapping to child devices.
Allow the IRQ to be shared among instances.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260106164416.67074-8-adrian.hunter@intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
When I3C is disabled, unused functions are removed by the linker because
the driver relies on regmap and no I3C devices are registered, so normal
I3C paths are never called.
However, some drivers may still call low-level I3C transfer helpers.
Provide stub implementations to avoid adding conditional ifdefs everywhere.
Add stubs for i3c_device_do_xfers() and
i3c_device_get_supported_xfer_mode() only. Other stubs will be introduced
when they are actually needed.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512230418.nu3V6Yua-lkp@intel.com/
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251230145718.4088694-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Drop i3c_priv_xfer and i3c_device_do_priv_xfers() after all driver switch
to use new API.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251215172405.2982801-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add helpers to enable and disable the SDCA IRQs by Function. These are
useful to sequence the powering down and up around system suspend.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20260109145206.3456151-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, mac80211 allows key installation only after association
completes. However, Enhanced Privacy Protection Key Exchange (EPPKE)
requires key installation before association to enable encryption and
decryption of (Re)Association Request and Response frames.
Add support to install keys prior to association when the peer is an
Enhanced Privacy Protection (EPP) peer that requires encryption and
decryption of (Re)Association Request and Response frames.
Introduce a new boolean parameter "epp_peer" in the "ieee80211_sta"
profile to indicate that the peer supports the Enhanced Privacy
Protection Key Exchange (EPPKE) protocol. For non-AP STA mode, it
is set when the authentication algorithm is WLAN_AUTH_EPPKE during
station profile initialization. For AP mode, it is set during
NL80211_CMD_NEW_STA and NL80211_CMD_ADD_LINK_STA.
When "epp_peer" parameter is set, mac80211 now accepts keys before
association and enables encryption of the (Re)Association
Request/Response frames.
Co-developed-by: Sai Pratyusha Magam <sai.magam@oss.qualcomm.com>
Signed-off-by: Sai Pratyusha Magam <sai.magam@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260114111900.2196941-6-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduce a new netlink attribute NL80211_ATTR_EPP_PEER
to be used with NL80211_CMD_NEW_STA and
NL80211_CMD_ADD_LINK_STA for the userspace to indicate
that a non-AP STA is an Enhanced Privacy Protection (EPP)
peer.
Co-developed-by: Rohan Dutta <quic_drohan@quicinc.com>
Signed-off-by: Rohan Dutta <quic_drohan@quicinc.com>
Signed-off-by: Sai Pratyusha Magam <sai.magam@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260114111900.2196941-5-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduce an extended feature flag that allows drivers to signal
support for encryption of (Re)Association Request and Response frames
in both non-AP STA and AP mode, as specified in specification
"IEEE P802.11bi/D3.0, 12.16.6".
Signed-off-by: Ainy Kumari <ainy.kumari@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260114111900.2196941-3-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add an extended feature flag NL80211_EXT_FEATURE_EPPKE to allow a
driver to indicate support for the Enhanced Privacy Protection Key
Exchange (EPPKE) authentication protocol in non-AP STA mode, as
defined in "IEEE P802.11bi/D3.0, 12.16.9".
In case of SME in userspace, the Authentication frame body is prepared
in userspace while the driver finalizes the Authentication frame once
it receives the required fields and elements. The driver indicates
support for EPPKE using the extended feature flag so that userspace
can initiate EPPKE authentication.
When the feature flag is set, process EPPKE Authentication frames from
userspace in non-AP STA mode. If the flag is not set, reject EPPKE
Authentication frames.
Define a new authentication type NL80211_AUTHTYPE_EPPKE for EPPKE.
Signed-off-by: Ainy Kumari <ainy.kumari@oss.qualcomm.com>
Co-developed-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260114111900.2196941-2-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
phy common properties
Vladimir Oltean <vladimir.oltean@nxp.com> wrote:
Introduce "rx-polarity" and "tx-polarity" device tree properties with
Kunit tests
|
|
Add helpers in the generic PHY folder which can be used using 'select
PHY_COMMON_PROPS' from Kconfig, without otherwise needing to
enable GENERIC_PHY.
These helpers need to deal with the slight messiness of the fact that
the polarity properties are arrays per protocol, and with the fact that
there is no default value mandated by the standard properties, all
default values depend on driver and protocol (PHY_POL_NORMAL may be a
good default for SGMII, whereas PHY_POL_AUTO may be a good default for
PCIe).
Push the supported mask of polarities to these helpers, to simplify
drivers such that they don't need to validate what's in the device tree
(or other firmware description).
Add a KUnit test suite to make sure that the API produces the expected
results. The fact that we use fwnode structures means we can validate
with software nodes, and as opposed to the device_property API, we can
bypass the need to have a device structure.
Co-developed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20260111093940.975359-6-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Differential signaling is a technique for high-speed protocols to be
more resilient to noise. At the transmit side we have a positive and a
negative signal which are mirror images of each other. At the receiver,
if we subtract the negative signal (say of amplitude -A) from the
positive signal (say +A), we recover the original single-ended signal at
twice its original amplitude. But any noise, like one coming from EMI
from outside sources, is supposed to have an almost equal impact upon
the positive (A + E, E being for "error") and negative signal (-A + E).
So (A + E) - (-A + E) eliminates this noise, and this is what makes
differential signaling useful.
Except that in order to work, there must be strict requirements observed
during PCB design and layout, like the signal traces needing to have the
same length and be physically close to each other, and many others.
Sometimes it is not easy to fulfill all these requirements, a simple
case to understand is when on chip A's pins, the positive pin is on the
left and the negative is on the right, but on the chip B's pins (with
which A tries to communicate), positive is on the right and negative on
the left. The signals would need to cross, using vias and other ugly
stuff that affects signal integrity (introduces impedance
discontinuities which cause reflections, etc).
So sometimes, board designers intentionally connect differential lanes
the wrong way, and expect somebody else to invert that signal to recover
useful data. This is where RX and TX polarity inversion comes in as a
generic concept that applies to any high-speed serial protocol as long
as it uses differential signaling.
I've stopped two attempts to introduce more vendor-specific descriptions
of this only in the past month:
https://lore.kernel.org/linux-phy/20251110110536.2596490-1-horatiu.vultur@microchip.com/
https://lore.kernel.org/netdev/20251028000959.3kiac5kwo5pcl4ft@skbuf/
and in the kernel we already have merged:
- "st,px_rx_pol_inv"
- "st,pcie-tx-pol-inv"
- "st,sata-tx-pol-inv"
- "mediatek,pnswap"
- "airoha,pnswap-rx"
- "airoha,pnswap-tx"
and maybe more. So it is pretty general.
One additional element of complexity is introduced by the fact that for
some protocols, receivers can automatically detect and correct for an
inverted lane polarity (example: the PCIe LTSSM does this in the
Polling.Configuration state; the USB 3.1 Link Layer Test Specification
says that the detection and correction of the lane polarity inversion in
SuperSpeed operation shall be enabled in Polling.RxEQ.). Whereas for
other protocols (SGMII, SATA, 10GBase-R, etc etc), the polarity is all
manual and there is no detection mechanism mandated by their respective
standards.
So why would one even describe rx-polarity and tx-polarity for protocols
like PCIe, if it had to always be PHY_POL_AUTO?
Related question: why would we define the polarity as an array per
protocol? Isn't the physical PCB layout protocol-agnostic, and aren't we
describing the same physical reality from the lens of different protocols?
The answer to both questions is because multi-protocol PHYs exist
(supporting e.g. USB2 and USB3, or SATA and PCIe, or PCIe and Ethernet
over the same lane), one would need to manually set the polarity for
SATA/Ethernet, while leaving it at auto for PCIe/USB 3.0+.
I also investigated from another angle: what if polarity inversion in
the PHY is one layer, and then the PCIe/USB3 LTSSM polarity detection is
another layer on top? Then rx-polarity = <PHY_POL_AUTO> doesn't make
sense, it can still be rx-polarity = <PHY_POL_NORMAL> or <PHY_POL_INVERT>,
and the link training state machine figures things out on top of that.
This would radically simplify the design, as the elimination of
PHY_POL_AUTO inherently means that the need for a property array per
protocol also goes away.
I don't know how things are in the general case, but at least in the 10G
and 28G Lynx SerDes blocks from NXP Layerscape devices, this isn't the
case, and there's only a single level of RX polarity inversion: in the
SerDes lane. In the case of PCIe, the controller is in charge of driving
the RDAT_INV bit autonomously, and it is read-only to software.
So the existence of this kind of SerDes lane proves the need for
PHY_POL_AUTO to be a third state.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260111093940.975359-5-vladimir.oltean@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
IIO: 1st set of fixes for the 6.19 cycle
The usual mixed bag of fixes for ancient problems plus some more
recent ones.
adi,ad7280a
- Check for errors from spi_setup().
adi,ad3552r
- Fix potential buffer overflow when setting to use the internal ramp.
adi,ax5695r
- Fill in the data for this device in the chip info table.
adi,ad7606
- Don't store a negative error in an unsigned int.
adi,ad9467
- Fix incorrect register mask value.
adi,adxl380
- Fix inverted condition for whether INT1 interrupt present in dt.
atmel,at91-sama5d2
- Cancel work on remove to avoid a potential use-after-free
invensense,icm45600
- Fix temperature scaling.
samsung,eynos_adc
- Use of_platform_depolulate() to correctly clear up such that child
devices are created correctly if the driver is rebound.
sensiron,scd4x
- Fix incorrect endianness reported to user-space.
st,accel
- Fix gain reported for the iis329dq.
st,lsm6dsx
- Hide event related interfaces on parts that don't support events.
ti,pac1934
- Ensure output of clamp() is used rather than unclamped value.
* tag 'iio-fixes-for-6.19a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: dac: ad3552r-hs: fix out-of-bound write in ad3552r_hs_write_data_source
iio: accel: iis328dq: fix gain values
iio: core: add separate lockdep class for info_exist_lock
iio: chemical: scd4x: fix reported channel endianness
iio: imu: inv_icm45600: fix temperature offset reporting
iio: adc: exynos_adc: fix OF populate on driver rebind
iio: dac: ad5686: add AD5695R to ad5686_chip_info_tbl
iio: accel: adxl380: fix handling of unavailable "INT1" interrupt
iio: imu: st_lsm6dsx: fix iio_chan_spec for sensors without event detection
iio: adc: pac1934: Fix clamped value in pac1934_reg_snapshot
iio: adc: ad9467: fix ad9434 vref mask
iio: adc: ad7606: Fix incorrect type for error return variable
iio: adc: ad7280a: handle spi_setup() errors in probe()
iio: adc: at91-sama5d2_adc: Fix potential use-after-free in sama5d2_adc driver
|
|
Add a generic TEE revision sysfs attribute backed by a new
optional get_tee_revision() callback. The revision string is
diagnostic-only and must not be used to infer feature support.
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
The last user of defined structures s3c_hwmon_pdata and s3c_hwmon_chcfg
was removed in commit 0d297df03890 ("ARM: s3c: simplify platform code"),
thus the platform data header file itself can be removed also.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://patch.msgid.link/20260112211554.3755188-1-vz@mleia.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
When a non-NCQ command is issued while NCQ commands are being executed,
ata_scsi_qc_issue() indicates to the SCSI layer that the command issuing
should be deferred by returning SCSI_MLQUEUE_XXX_BUSY. This command
deferring is correct and as mandated by the ACS specifications since
NCQ and non-NCQ commands cannot be mixed.
However, in the case of a host adapter using multiple submission queues,
when the target device is under a constant load of NCQ commands, there
are no guarantees that requeueing the non-NCQ command will be executed
later and it may be deferred again repeatedly as other submission queues
can constantly issue NCQ commands from different CPUs ahead of the
non-NCQ command. This can lead to very long delays for the execution of
non-NCQ commands, and even complete starvation for these commands in the
worst case scenario.
Since the block layer and the SCSI layer do not distinguish between
queueable (NCQ) and non queueable (non-NCQ) commands, libata-scsi SAT
implementation must ensure forward progress for non-NCQ commands in the
presence of NCQ command traffic. This is similar to what SAS HBAs with a
hardware/firmware based SAT implementation do.
Implement such forward progress guarantee by limiting requeueing of
non-NCQ commands from ata_scsi_qc_issue(): when a non-NCQ command is
received and NCQ commands are in-flight, do not force a requeue of the
non-NCQ command by returning SCSI_MLQUEUE_XXX_BUSY and instead return 0
to indicate that the command was accepted but hold on to the qc using
the new deferred_qc field of struct ata_port.
This deferred qc will be issued using the work item deferred_qc_work
running the function ata_scsi_deferred_qc_work() once all in-flight
commands complete, which is checked with the port qc_defer() callback
return value indicating that no further delay is necessary. This check
is done using the helper function ata_scsi_schedule_deferred_qc() which
is called from ata_scsi_qc_complete(). This thus excludes this mechanism
from all internal non-NCQ commands issued by ATA EH.
When a port deferred_qc is non NULL, that is, the port has a command
waiting for the device queue to drain, the issuing of all incoming
commands (both NCQ and non-NCQ) is deferred using the regular busy
mechanism. This simplifies the code and also avoids potential denial of
service problems if a user issues too many non-NCQ commands.
Finally, whenever ata EH is scheduled, regardless of the reason, a
deferred qc is always requeued so that it can be retried once EH
completes. This is done by calling the function
ata_scsi_requeue_deferred_qc() from ata_eh_set_pending(). This avoids
the need for any special processing for the deferred qc in case of NCQ
error, link or device reset, or device timeout.
Reported-by: Xingui Yang <yangxingui@huawei.com>
Reported-by: Igor Pylypiv <ipylypiv@google.com>
Fixes: bdb01301f3ea ("scsi: Add host and host template flag 'host_tagset'")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Tested-by: Igor Pylypiv <ipylypiv@google.com>
Tested-by: Xingui Yang <yangxingui@huawei.com>
|
|
It would be useful to be able to check for potential DMA pages beyond
just ZONE_DMA - generalise the existing has_managed_dma() function to
allow checking other zones too.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: David Hildenbrand (Red Hat) <david@kernel.org>
Acked-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Tested-by: Vladimir Kondratiev <vladimir.kondratiev@mobileye.com>
Reviewed-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/bd002d2351074e57be1ca08f03f333debac658fb.1768230104.git.robin.murphy@arm.com
|
|
XAUI (eXtended Attachment Unit Interface) is a high-speed serial interface
standard for 10 Gigabit Ethernet (10GbE). It uses four lanes with each
lane operating at 3.125 Gbps (totaling 10 Gbps), to extend the XGMII
interface across circuit boards, commonly used in backplanes for
networking switches and high-performance computing. XAUI is defined as a
standardized instantiation of XGMII Extender in the IEEE 802.3
specification.
Add definition for XAUI PHY type.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
[s-vadapalli: added detailed description of XAUI in the commit message]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260112054636.108027-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Type punning is necessary for get/put_unaligned() but the use of a packed
struct violates strict aliasing rules, requiring -fno-strict-aliasing to be
passed to the C compiler.
Switch to using memcpy() so that -fno-strict-aliasing isn't necessary.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20251016205126.2882625-3-irogers@google.com
|
|
The cache parameter of getcpu() is useless nowadays for various reasons.
* It is never passed by userspace for either the vDSO or syscalls.
* It is never used by the kernel.
* It could not be made to work on the current vDSO architecture.
* The structure definition is not part of the UAPI headers.
* vdso_getcpu() is superseded by restartable sequences in any case.
Remove the struct and its header.
As a side-effect this gets rid of an unwanted inclusion of the linux/
header namespace from vDSO code.
[ tglx: Adapt to s390 upstream changes */
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # s390
Link: https://patch.msgid.link/20251230-getcpu_cache-v3-1-fb9c5f880ebe@linutronix.de
|
|
In commit 3bdbd0858df6 ("Input: adp5589: remove the driver") the last user
of include/linux/input/adp5589.h was removed along with the whole driver,
thus the header file can be also removed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Fixes: 3bdbd0858df6 ("Input: adp5589: remove the driver")
Link: https://patch.msgid.link/20260113151140.3843753-1-vz@mleia.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
drivers-for-6.20
Merge the support for loading and managing the TrustZone-based remote
processors found in the Glymur platform through a topic branch, as it's
a mix of qcom-soc and remoteproc patches.
|
|
Implement .ndo_tx_timeout for MANA so any stalled TX queue can be detected
and a device-controlled port reset for all queues can be scheduled to a
ordered workqueue. The reset for all queues on stall detection is
recomended by hardware team.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Link: https://patch.msgid.link/20260112130552.GA11785@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that all PHY drivers that support downstream SFP have been converted
to phy_port serdes handling, we can make the generic PHY SFP handling
mandatory, thus making all phylib sfp helpers static.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-14-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert the Marvell10G driver to use the generic SFP handling, through a
dedicated .attach_port() handler to populate the port's supported
interfaces.
As the 88x3310 supports multiple MDI, the .attach_port() logic handles
both SFP attach with 10GBaseR support, and support for the "regular"
port that usually is a BaseT port.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-11-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are currently 4 PHY drivers that can drive downstream SFPs:
marvell.c, marvell10g.c, at803x.c and marvell-88x2222.c. Most of the
logic is boilerplate, either calling into generic phylib helpers (for
SFP PHY attach, bus attach, etc.) or performing the same tasks with a
bit of validation :
- Getting the module's expected interface mode
- Making sure the PHY supports it
- Optionaly perform some configuration to make sure the PHY outputs
the right mode
This can be made more generic by leveraging the phy_port, and its
configure_mii() callback which allows setting a port's interfaces when
the port is a serdes.
Introduce a generic PHY SFP support. If a driver doesn't probe the SFP
bus itself, but an SFP phandle is found in devicetree/firmware, then the
generic PHY SFP support will be used, relying on port ops.
PHY driver need to :
- Register a .attach_port() callback
- When a serdes port is registered to the PHY, drivers must set
port->interfaces to the set of PHY_INTERFACE_MODE the port can output
- If the port has limitations regarding speed, duplex and aneg, the
port can also fine-tune the final linkmodes that can be supported
- The port may register a set of ops, including .configure_mii(), that
will be called at module_insert time to adjust the interface based on
the module detected.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-8-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethernet provides a wide variety of layer 1 protocols and standards for
data transmission. The front-facing ports of an interface have their own
complexity and configurability.
Introduce a representation of these front-facing ports. The current code
is minimalistic and only support ports controlled by PHY devices, but
the plan is to extend that to SFP as well as raw Ethernet MACs that
don't use PHY devices.
This minimal port representation allows describing the media and number
of pairs of a BaseT port. From that information, we can derive the
linkmodes usable on the port, which can be used to limit the
capabilities of an interface.
For now, the port pairs and medium is derived from devicetree, defined
by the PHY driver, or populated with default values (as we assume that
all PHYs expose at least one port).
The typical example is 100M ethernet. 100BaseTX works using only 2
pairs on a Cat 5 cables. However, in the situation where a 10/100/1000
capable PHY is wired to its RJ45 port through 2 pairs only, we have no
way of detecting that. The "max-speed" DT property can be used, but a
more accurate representation can be used :
mdi {
connector-0 {
media = "BaseT";
pairs = <2>;
};
};
From that information, we can derive the max speed reachable on the
port.
Another benefit of having that is to avoid vendor-specific DT properties
(micrel,fiber-mode or ti,fiber-mode).
This basic representation is meant to be expanded, by the introduction
of port ops, userspace listing of ports, and support for multi-port
devices.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260108080041.553250-4-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an effort to have a better representation of Ethernet ports,
introduce enumeration values representing the various ethernet Mediums.
This is part of the 802.3 naming convention, for example :
1000 Base T 4
| | | |
| | | \_ pairs (4)
| | \___ Medium (T == Twisted Copper Pairs)
| \_______ Baseband transmission
\____________ Speed
Other example :
10000 Base K X 4
| | \_ lanes (4)
| \___ encoding (BaseX is 8b/10b while BaseR is 66b/64b)
\_____ Medium (K is backplane ethernet)
In the case of representing a physical port, only the medium and number
of pairs should be relevant. One exception would be 1000BaseX, which is
currently also used as a medium in what appears to be any of 1000BaseSX,
1000BaseCX, 1000BaseLX, 1000BaseEX, 1000BaseBX10 and some other.
This was reflected in the mediums associated with the 1000BaseX linkmode.
These mediums are set in the net/ethtool/common.c lookup table that
maintains a list of all linkmodes with their number of pairs, medium,
encoding, speed and duplex.
One notable exception to this is 100BaseT Ethernet. It emcompasses 100BaseTX,
which is a 2-pairs protocol but also 100BaseT4, that will also work on 4-pairs
cables. As we don't make a disctinction between these, the lookup table
contains 2 sets of pair numbers, indicating the min number of pairs for a
protocol to work and the "nominal" number of pairs as well.
Another set of exceptions are linkmodes such 100000baseLR4_ER4, where
the same link mode seems to represent 100GBaseLR4 and 100GBaseER4. The
macro __DEFINE_LINK_MODE_PARAMS_MEDIUMS is here used to populate the
.mediums bitfield with all appropriate mediums.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260108080041.553250-3-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow memory providers to configure rx queues with a custom receive
page size. It's passed in struct pp_memory_provider_params, which is
copied into the queue, so it's preserved across queue restarts. Then,
it's propagated to the driver in a new queue config parameter.
Drivers should explicitly opt into using it by setting
QCFG_RX_PAGE_SIZE, in which case they should implement ndo_default_qcfg,
validate the size on queue restart and honour the current config in case
of a reset.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
|
|
We'll need to pass extra parameters when allocating a queue for memory
providers. Define a new structure for queue configurations, and pass it
to qapi callbacks. It's empty for now, actual parameters will be added
in following patches.
Configurations should persist across resets, and for that they're
default-initialised on device registration and stored in struct
netdev_rx_queue. We also add a new qapi callback for defaulting a given
config. It must be implemented if a driver wants to use queue configs
and is optional otherwise.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
|
|
Trivial change, reduce the indent. I think the original is copied
from real NDOs. It's unnecessarily deep, makes passing struct args
problematic.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Tariq Toukan says:
====================
mlx5-next updates 2026-01-13
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add IFC bits for extended ETS rate limit bandwidth value
net/mlx5: Add support for querying bond speed
net/mlx5: Handle port and vport speed change events in MPESW
net/mlx5: Propagate LAG effective max_tx_speed to vports
net/mlx5: Add max_tx_speed and its CAP bit to IFC
====================
Link: https://patch.msgid.link/1768299471-1603093-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix KVM's long-standing buggy handling of SVM's exit_code as a 32-bit
value. Per the APM and Xen commit d1bd157fbc ("Big merge the HVM
full-virtualisation abstractions.") (which is arguably more trustworthy
than KVM), offset 0x70 is a single 64-bit value:
070h 63:0 EXITCODE
Track exit_code as a single u64 to prevent reintroducing bugs where KVM
neglects to correctly set bits 63:32.
Fixes: 6aa8b732ca01 ("[PATCH] kvm: userspace interface")
Cc: Jim Mattson <jmattson@google.com>
Cc: Yosry Ahmed <yosry.ahmed@linux.dev>
Reviewed-by: Yosry Ahmed <yosry.ahmed@linux.dev>
Link: https://patch.msgid.link/20251230211347.4099600-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Improve btf_find_by_name_kind() performance by adding binary search
support for sorted types. Falls back to linear search for compatibility.
Signed-off-by: Donglin Peng <pengdonglin@xiaomi.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20260109130003.3313716-7-dolinux.peng@gmail.com
|
|
The function drm_property_replace_blob_from_id() allows checking whether
the blob size is equal to a predefined value. In case of variable-size
properties (like the gamma / degamma LUTs) we might want to check for
the blob size against the maximum, allowing properties of the size
lesser than the max supported by the hardware. Extend the function in
order to support such checks.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260106-drm-fix-lut-checks-v3-2-f7f979eb73c8@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
We have a helper to get property values for non-atomic drivers and
another one default property values for atomic drivers. In some cases we
need the ability to get value of immutable property, no matter what kind
of driver it is. Implement new property-related helper,
drm_object_immutable_property_get_value(), which lets the caller to get
the value of the immutable property.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260106-drm-fix-lut-checks-v3-1-f7f979eb73c8@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
... or visible outside of audit, really. Note that references
held in delayed_filename always have refcount 1, and from the
moment of complete_getname() or equivalent point in getname...()
there won't be any references to struct filename instance left
in places visible to other threads.
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
