| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Before the commit 755391121038 ("net: mana: Allocate MSI-X vectors
dynamically"), all the MANA IRQs were assigned statically and together
during early driver load.
After this commit, the IRQ allocation for MANA was done in two phases.
HWC IRQ allocated earlier and then, queue IRQs dynamically added at a
later point. By this time, the IRQ weights on vCPUs can become imbalanced
and if IRQ count is greater than the vCPU count the topology aware IRQ
distribution logic in MANA can cause multiple MANA IRQs to land on the
same vCPUs, while other sibling vCPUs have none (case 1).
On SMP enabled, low-vCPU systems, this becomes a bigger problem as the
softIRQ handling overhead of two IRQs on the same vCPUs becomes much more
than their overheads if they were spread across sibling vCPUs.
In such cases when many parallel TCP connections are tested, the
throughput drops significantly.
Fix the affinity assignment logic, in cases where the IRQ count is greater
than the vCPU count and when IRQs are added dynamically, by utilizing all
the vCPUs irrespective of their NUMA/core bindings (case 2).
The results of setting the affinity and hint to NULL were also studied,
and we observed that, with this logic if there are pre-existing IRQs
allocated on the VM (apart from MANA), during MANA IRQs allocation, it
leads to clustering of the MANA queue IRQs again (case 3).
=======================================================
Case 1: without this patch
=======================================================
4 vcpu(2 cores), 5 MANA IRQs (1 HWC + 4 Queue)
TYPE effective vCPU aff
=======================================================
IRQ0: HWC 0
IRQ1: mana_q1 0
IRQ2: mana_q2 2
IRQ3: mana_q3 0
IRQ4: mana_q4 3
%soft on each vCPU(mpstat -P ALL 1) on receiver
vCPU 0 1 2 3
=======================================================
pass 1: 38.85 0.03 24.89 24.65
pass 2: 39.15 0.03 24.57 25.28
pass 3: 40.36 0.03 23.20 23.17
=======================================================
Case 2: with this patch
=======================================================
4 vcpu(2 cores), 5 MANA IRQs (1 HWC + 4 Queue)
TYPE effective vCPU aff
=======================================================
IRQ0: HWC 0
IRQ1: mana_q1 0
IRQ2: mana_q2 1
IRQ3: mana_q3 2
IRQ4: mana_q4 3
%soft on each vCPU(mpstat -P ALL 1) on receiver
vCPU 0 1 2 3
=======================================================
pass 1: 15.42 15.85 14.99 14.51
pass 2: 15.53 15.94 15.81 15.93
pass 3: 16.41 16.35 16.40 16.36
=======================================================
Case 3: with affinity set to NULL
=======================================================
4 vCPU(2 cores), 5 MANA IRQs (1 HWC + 4 Queue)
TYPE effective vCPU aff
=======================================================
IRQ0: HWC 0
IRQ1: mana_q1 2
IRQ2: mana_q2 3
IRQ3: mana_q3 2
IRQ4: mana_q4 3
=======================================================
Throughput Impact(in Gbps, same env)
=======================================================
TCP conn with patch w/o patch aff NULL
20480 15.65 7.73 5.25
10240 15.63 8.93 5.77
8192 15.64 9.69 7.16
6144 15.64 13.16 9.33
4096 15.69 15.75 13.50
2048 15.69 15.83 13.61
1024 15.71 15.28 13.60
Fixes: 755391121038 ("net: mana: Allocate MSI-X vectors dynamically")
Cc: stable@vger.kernel.org
Co-developed-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com>
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Yury Norov <ynorov@nvidia.com>
Link: https://patch.msgid.link/20260624072138.1632849-1-shradhagupta@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull ipmi updates from Corey Minyard:
"Lots of little tweaks.
Nothing huge, the biggest issue was a possible refcount underflow that
could cause a memory leak in some situations. Otherwise, fixing
formatting and style things and some docs typos"
* tag 'for-linus-7.2-1' of https://github.com/cminyard/linux-ipmi:
docs: ipmi: Fix path of the "hotmod" module parameter
ipmi: Drop unused assignment of platform_device_id driver data
ipmi: si: Use platform_get_irq_optional() to retrieve interrupt
ipmi: fix refcount leak in i_ipmi_request()
ipmi:ssif: Drop unused assignment of platform_device_id driver data
ipmi: Fix user refcount underflow in event delivery
ipmi: Use named initializers for struct i2c_device_id
ipmi: Use LIST_HEAD() to initialize on stack list head
ipmi:kcs: Reduce the number of retries
|
|
No functional changes intended.
Signed-off-by: Gary Guo <gary@garyguo.net>
Acked-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260610141359.1033755-1-gary@kernel.org
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
|
|
sparx5_register_notifier_blocks() registers the switchdev blocking
notifier before allocating the ordered workqueue. If the workqueue
allocation fails, the error path unregisters the switchdev and netdevice
notifiers, but leaves the blocking notifier registered.
Add a separate error label for the workqueue allocation failure path and
unregister the switchdev blocking notifier there.
Fixes: d6fce5141929 ("net: sparx5: add switching support")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260623115714.2192074-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nix_setup_bpids() allocates bp->bpids with rvu_alloc_bitmap(), which uses
a plain kcalloc(). If any of the following devm_kcalloc() allocations for
the BPID mapping arrays fails, the function returns without freeing the
bitmap. Free the BPID bitmap before returning from those error paths.
Fixes: d6212d2e41a0 ("octeontx2-af: Create BPIDs free pool")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260623114316.2182271-1-haoxiang_li2024@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For i.MX94 series, all the standalone ENETCs do not support SR-IOV, so
pf->caps.num_vsi is zero. This leads to a divide-by-zero in
enetc4_default_rings_allocation() when distributing rings among PF and
VFs.
Division by zero is undefined behavior in C. On ARM64, the UDIV/SDIV
instructions silently return zero rather than raising an exception, so
the issue does not cause a visible crash. However, relying on this
behavior is incorrect and poses a cross-platform compatibility risk.
Add an explicit check for num_vsi == 0 and return early after the PF's
rings have been configured.
Fixes: 2d673b0e2f8d ("net: enetc: add standalone ENETC support for i.MX94")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260624072726.1238903-1-wei.fang@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
usbio_bulk_msg() copies bpkt_len = le16_to_cpu(bpkt->len) bytes out of
the bulk IN buffer (usbio->rxbuf, allocated with size usbio->rxbuf_len)
into the caller's buffer. bpkt_len is fully controlled by the device
and is only checked against ibuf_len; ibuf_len in turn is checked
against usbio->txbuf_len, not against rxbuf_len:
if ((obuf_len > (usbio->txbuf_len - sizeof(*bpkt))) ||
(ibuf_len > (usbio->txbuf_len - sizeof(*bpkt))))
return -EMSGSIZE;
txbuf_len and rxbuf_len are taken independently from the bulk OUT and
bulk IN endpoint wMaxPacketSize in usbio_probe(). A malicious or
malfunctioning device that advertises a large bulk OUT endpoint and a
small bulk IN endpoint (e.g. by claiming one of the quirk-free IDs such
as the Lattice NX33U, 0x2ac1:0x20cb) therefore makes ibuf_len, and
hence the device-supplied bpkt_len, exceed rxbuf_len. memcpy() then
reads up to txbuf_len - rxbuf_len bytes past the end of the rxbuf slab
object. The over-read bytes are handed back to the i2c layer and on to
user space through i2c-dev, disclosing adjacent slab memory; with KASAN
this is reported as a slab-out-of-bounds read.
The number of bytes actually received is already known: act equals the
URB actual_length and is bounded by rxbuf_len. Reject any response
that claims more payload than was received, mirroring the existing
"act < sizeof(*bpkt)" check just above.
The control path (usbio_ctrl_msg()) is not affected: it uses a single
buffer (ctrlbuf) for both directions, so its analogous copy can never
leave the allocation.
Found by code review. The out-of-bounds read was confirmed under
AddressSanitizer with a faithful userspace model of usbio_bulk_msg()'s
receive path (an rxbuf_len-sized buffer, the same act/ibuf_len/bpkt_len
checks and the memcpy). A USB raw-gadget + dummy_hcd reproducer is
also available.
Fixes: 121a0f839dbb ("usb: misc: Add Intel USBIO bridge driver")
Cc: stable <stable@kernel.org>
Signed-off-by: HE WEI (ギカク) <skyexpoc@gmail.com>
Link: https://patch.msgid.link/20260624090952.86439-1-skyexpoc@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mtu3_gadget_queue() maps the request before checking whether
the QMU GPD ring can accept another transfer. the request is
returned with -EAGAIN before it is linked on the endpoint
request list if mtu3_prepare_transfer() fails.
Normal completion and dequeue paths unmap requests from
mtu3_req_complete(), but this error path never reaches that
helper, so the DMA mapping is left active. Unmap the request
before returning from the failed queue path.
Fixes: df2069acb005 ("usb: Add MediaTek USB3 DRD driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Link: https://patch.msgid.link/20260623093325.2105323-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If dwc3_meson_g12a_resume() succeeds in calling
reset_control_reset(), an internal triggered_count reference is
acquired. If any later step fails (usb_init, phy_init,
phy_power_on, regulator_enable, or usb_post_init), the function
returns the error without rearming the reset control. This leaks
the reference and leaves the reset control in a triggered state,
causing future reset_control_reset() calls to incorrectly return
early as if already reset.
Add an error path that calls reset_control_rearm() to balance
the reference before returning the error.
Cc: stable <stable@kernel.org>
Fixes: 5b0ba0caaf3a ("usb: dwc3: meson-g12a: refactor usb init")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20260611131121.81784-1-vulab@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job.
Fixes: 53e6242db8d6 ("usb: gadget: composite: add USB_DT_OTG request handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Link: https://patch.msgid.link/20260527150832.2943293-1-maoyixie.tju@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ueagle-atm uses the asynchronous request_firmware_nowait() in .probe(),
but does not wait for its completion, not even in .disconnect(); so, if the
device is unplugged meanwhile, its teardown runs concurrently with that.
Even though this inconsistency is worth addressing on its own, it has also
triggered several bug reports in syzbot over the years (some auto-closed)
where the firmware sysfs fallback mechanism (CONFIG_FW_LOADER_USER_HELPER)
creates a firmware subdirectory in the device directory during its removal,
which might hit unexpected conditions in kernfs, apparently, depending at
which point the add and remove operations raced. (See links.)
The pattern is:
usb ?-?: Direct firmware load for ueagle-atm/eagle?.fw failed with error -2
usb ?-?: Falling back to sysfs fallback for: ueagle-atm/eagle?.fw
<ERROR>
Call trace:
...
kernfs_create_dir_ns
sysfs_create_dir_ns
create_dir
kobject_add_internal
kobject_add_varg
kobject_add
class_dir_create_and_add
get_device_parent
device_add
fw_load_sysfs_fallback
fw_load_from_user_helper
firmware_fallback_sysfs
_request_firmware
request_firmware_work_func
...
(Some variations are observed, after fw_load_sysfs_fallback(), e.g., [1].)
While the kernfs side is being looked at, the ueagle-atm side can be fixed
by waiting for the pre-firmware load in the .disconnect() handler.
This change has a similar approach to previous work by Andrey Tsygunka [2]
(wait_for_completion() in .disconnect()), but it is relatively different in
design/implementation; using the Originally-by tag for credit assignment.
This has been tested with:
- synthetic reproducer to check the error path;
- USB gadget (virtual device) to check the firmware upload path;
- QEMU device emulator to check the device ID re-enumeration path;
(The latter two were written by Claude; no other code/text in this commit.)
Links (year first reported):
2025 https://syzbot.org/bug?extid=ce1e5a1b4e086b43e56d
2025 https://syzbot.org/bug?extid=9af8471255ac36e34fd4
2024 https://syzbot.org/bug?extid=306212936b13e520679d
2023 https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
2022 https://syzbot.org/bug?extid=782984d6f1701b526edb
2021 https://syzbot.org/bug?id=f3f221579f4ef7e9691281f3c6f56c05f83e8490
2021 https://syzbot.org/bug?id=84d86f0d71394829df6fc53daf6642c045983881
2021 https://syzbot.org/bug?id=3302dc1c0e2b9c94f2e8edb404eabc9267bc6f90
[1] https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
[2] https://lore.kernel.org/lkml/20250410093146.3776801-2-aitsygunka@yandex.ru/
Cc: stable <stable@kernel.org>
Reported-by: syzbot+ce1e5a1b4e086b43e56d@syzkaller.appspotmail.com
Closes: https://syzbot.org/bug?extid=ce1e5a1b4e086b43e56d
Reported-by: syzbot+306212936b13e520679d@syzkaller.appspotmail.com
Closes: https://syzbot.org/bug?extid=306212936b13e520679d
Reported-by: syzbot+457452d30bcdda75ead2@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=457452d30bcdda75ead2
Originally-by: Andrey Tsygunka <aitsygunka@yandex.ru>
Fixes: b72458a80c75 ("[PATCH] USB: Eagle and ADI 930 usb adsl modem driver")
Assisted-by: Claude:claude-opus-4.7 # usb gadget & qemu device for testing
Signed-off-by: Mauricio Faria de Oliveira <mfo@igalia.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260526-ueagle-atm_req-fw-sync-v3-1-93c01961daaf@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* clk-microchip:
clk: at91: keep securam node alive while mapping it
clk: at91: sama7d65: add peripheral clock for I3C
clk: microchip: mpfs-ccc: fix peripheral driver registration failures after oob fix
clk: at91: sam9x7: Fix gmac_gclk clock definition
clk: at91: sam9x7: Rename macb0_clk to gmac_clk
clk: at91: sam9x7: Remove gmac peripheral clock with ID 67
clk: microchip: rename clk-core to clk-pic32
* clk-qcom: (32 commits)
clk: qcom: regmap-phy-mux: Rework the implementation
clk: qcom: a53: Corrected frequency multiplier for 1152MHz
clk: qcom: camcc-milos: Declare icc path dependency for CAMSS_TOP_GDSC
clk: qcom: gdsc: Support enabling interconnect path for power domain
dt-bindings: clock: qcom,milos-camcc: Document interconnect path
interconnect: Add devm_of_icc_get_by_index() as exported API for users
clk: qcom: camcc-x1p42100: Add support for camera clock controller
clk: qcom: camcc-x1e80100: Add support for camera QDSS debug clocks
clk: qcom: videocc-x1p42100: Add support for video clock controller
dt-bindings: clock: qcom: Add X1P42100 camera clock controller
dt-bindings: clock: qcom: Add X1P42100 video clock controller
clk: qcom: nord: negcc: add support for the USB2 PHY reset
dt-bindings: clock: qcom: add the definition for the USB2 PHY reset
clk: qcom: clk-rpmh: Make all VRMs optional
clk: qcom: Add support for global clock controller on Hawi
clk: qcom: clk-alpha-pll: Add support for Taycan EHA_T PLL
clk: qcom: Add Hawi TCSR clock controller driver
clk: qcom: rpmh: Add support for Hawi RPMH clocks
dt-bindings: clock: qcom: Add Hawi global clock controller
dt-bindings: clock: qcom: Add Hawi TCSR clock controller
...
|
|
into clk-next
* clk-ti:
clk: keystone: sci-clk: fix application of sizeof to pointer
clk: keystone: don't cache clock rate
* clk-samsung:
clk: samsung: exynos990: Fix PERIC0/1 USI clock types
clk: samsung: exynos850: mark APM I3C clocks as critical
* clk-rockchip:
clk: rockchip: allow COMPILE_TEST builds
clk: rockchip: rk3588: add GATE_GRF clocks for I2S MCLK output to IO
soc: rockchip: rk3588: add SYS_GRF SOC_CON6 register offset
clk: rockchip: add helper to register auxiliary GRFs
clk: rockchip: allow grf_type_sys lookup in aux_grf_table
dt-bindings: clock: rockchip,rk3588-cru: add I2S MCLK output to IO clock IDs
* clk-spacemit:
clk: spacemit: k3: Add PCIe DBI clock
dt-bindings: soc: spacemit: k3: Add PCIe DBI clock IDs
clk: spacemit: k3: Fix PCIe clock register offset
clk: spacemit: k3: Switch to pll2_d6 as parent for PCIe clock
|
|
into clk-next
* clk-renesas: (36 commits)
clk: renesas: r9a08g045: Drop unused pm_domain header file
clk: renesas: r8a779g0: Add DSC clock
clk: renesas: rzg2l: Rename iterator in for_each_mod_clock() to avoid shadowing
clk: renesas: r9a08g045: Drop unused DEF_G3S_MUX macro
clk: renesas: rzg2l: Rename RZG3L-prefixed PLL macros to CPG-prefixed ones
clk: renesas: rzg3s/rzg3l: Simplify PLL configuration macro
clk: renesas: rzg2l: Simplify SAM PLL configuration macro
clk: renesas: r8a73a4: Add ZT/ZTR trace clocks
dt-bindings: clock: renesas,cpg-clocks: Document ZT/ZTR trace clock on R-Mobile APE6
clk: renesas: r9a08g046: Add RSPI clocks and resets
clk: renesas: r9a08g046: Add SSIF-2 clocks and resets
clk: renesas: r9a08g046: Add RSCI clocks and resets
clk: renesas: cpg-mssr: Add number of clock cells check
clk: renesas: rzg2l: Refactor rzg3l_cpg_pll_clk_endisable()
clk: renesas: rzg2l: Consolidate DEF_MUX() and DEF_MUX_FLAGS()
clk: renesas: r9a08g046: Add IA55_PCLK to critical module clocks
clk: renesas: r9a09g047: Add support for LCDC{0,1} clocks and resets
clk: renesas: r9a09g047: Add support for DSI clocks and resets
clk: renesas: r9a09g047: Add support for SMUX2_DSI{0,1}_CLK
clk: renesas: r9a09g047: Add CLK_PLLDSI{0,1}_CSDIV clocks
...
* clk-socfpga:
clk: socfpga: agilex: implement l3_main_free_clk
* clk-amlogic:
dt-bindings: clock: amlogic: t7: Add missing mpll3 parent clock
dt-bindings: clock: amlogic: Fix redundant hyphen in "amlogic,t7-gp1--pll" string.
* clk-canaan:
clk: canaan: Add clock driver for Canaan K230
dt-bindings: clock: Add Canaan K230 clock controller
|
|
into clk-next
* clk-cleanup:
clk: hisilicon: Improve deallocation in error path
clk-lpc18xx-ccu: kzalloc + kcalloc to kzalloc_flex
clk: bulk: Use dev_err_probe() helper in of_clk_bulk_get()
clk: bcm: iproc-asiu: simplify allocation
clk: clk-max77686: kzalloc + kcalloc to kzalloc
clk: visconti: pll: use kzalloc_flex
clk: hisilicon: clkdivider-hi6220: use kzalloc_flex
clk: mvebu: use kzalloc_flex
* clk-mediatek:
clk: mediatek: mt7988: use MUX_CLR_SET for gate-less muxes
clk: mediatek: mt8192: use MUX_CLR_SET
clk: mediatek: add MUX_CLR_SET macro
* clk-marvell:
clk: mmp: pxa1908-apbcp: Add reset cells
clk: mmp: pxa1908-apbc: Add reset cells
dt-bindings: clock: marvell,pxa1908: Add #reset-cells
* clk-versal:
clk: clk-axi-clkgen: Add support versal timings
|
|
Currently, ffs_epfile_release unconditionally frees the endpoint's
read_buffer when a file descriptor is closed. If userspace explicitly
opens the endpoint multiple times and closes one, the read_buffer is
destroyed. This can lead to silent data loss if other file descriptors
are still actively reading from the endpoint.
By tying the lifetime of the read_buffer to the ffs_epfile structure itself
(which is destroyed when the functionfs instance is torn down in
ffs_epfiles_destroy), we eliminate the brittle dependency on open/release
calls while correctly matching the conceptual lifetime of unread data on
the hardware endpoint.
Fixes: 9353afbbfa7b ("usb: gadget: f_fs: buffer data from ‘oversized’ OUT requests")
Cc: stable <stable@kernel.org>
Assisted-by: Antigravity:gemini-3.1-pro
Signed-off-by: Neill Kapron <nkapron@google.com>
Link: https://patch.msgid.link/20260619040609.4010746-3-nkapron@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When parsing endpoint descriptors, ffs_data_got_descs() generates the
eps_addrmap which contains the endpoint direction. However, epfile->in
was previously only populated in ffs_func_eps_enable() which executes
upon USB host connection. As a result, early userspace ioctls like
FUNCTIONFS_DMABUF_ATTACH that run before the host connects would see
epfile->in as 0, leading to incorrect DMA directions.
By moving the initialization to ffs_epfiles_create(), epfile->in is
accurate before userspace opens the endpoint files.
Fixes: 7b07a2a7ca02 ("usb: gadget: functionfs: Add DMABUF import interface")
Cc: stable <stable@kernel.org>
Assisted-by: Antigravity:gemini-3.1-pro
Signed-off-by: Neill Kapron <nkapron@google.com>
Link: https://patch.msgid.link/20260619040609.4010746-2-nkapron@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The threaded IRQ handler ccg_irq_handler() calls ucsi_notify_common(),
which on a connector-change event calls ucsi_connector_change() and
schedules connector work. In ucsi_ccg_remove(), ucsi_destroy() frees
uc->ucsi (kfree) before free_irq() is called, so a handler invocation
already in flight may access the freed object after ucsi_destroy().
CPU 0 (remove) | CPU 1 (threaded IRQ)
ucsi_destroy(uc->ucsi) | ccg_irq_handler()
kfree(ucsi) // FREE | ucsi_notify_common(uc->ucsi) // USE
Move free_irq() before ucsi_destroy() in the remove path. It is kept
after ucsi_unregister(): ucsi_unregister() cancels connector work whose
handler issues GET_CONNECTOR_STATUS through ucsi_send_command_common(),
which waits for a completion that is signalled from the IRQ handler, so
the IRQ must stay active until that work has been cancelled.
The probe error path already orders free_irq() before ucsi_destroy().
This bug was found by static analysis.
Fixes: e32fd989ac1c ("usb: typec: ucsi: ccg: Move to the new API")
Cc: stable <stable@kernel.org>
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260616132011.103279-1-fanwu01@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes().
Assisted-by: Antigravity:gemini-3.5-flash
Fixes: 4ab8c18d4d67 ("usb: typec: Register a device for every mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: RD Babiera <rdbabiera@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260622220803.305750-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 18bcbcfe9ca2 ("USB: misc: legousbtower: semaphore to mutex")
Cc: stable <stable@kernel.org>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: ce0d7d3f575f ("usb: ldusb: ld_usb semaphore to mutex")
Cc: stable <stable@kernel.org>
Cc: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is
non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 54d2bc068fd2 ("USB: fix locking in idmouse")
Cc: stable@vger.kernel.org # 2.6.24
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mutex_unlock() may access the mutex structure after releasing the lock
and therefore cannot be used to manage lifetime of objects directly
(unlike spinlocks and refcounts). [1][2]
Use a kref to release the driver data to avoid use-after-free in
mutex_unlock() when release() races with disconnect().
[1] a51749ab34d9 ("locking/mutex: Document that mutex_unlock() is non-atomic")
[2] 2b9d9e0a9ba0 ("locking/mutex: Clarify that mutex_unlock(), and most
other sleeping locks, can still use the lock object
after it's unlocked")
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@kernel.org>
Reported-by: Yue Sun <samsun1006219@gmail.com>
Link: https://lore.kernel.org/r/20260618080204.38322-1-samsun1006219@gmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260622152612.116422-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Submitted write URBs are not stopped on close() and therefore need to be
stopped unconditionally on disconnect() to avoid use-after-free in the
completion handler.
Fixes: b5f8d46867ca ("USB: iowarrior: fix use-after-free after driver unbind")
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Reported-by: syzbot+ad2aac2febc3bedf0962@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/6a0ce39b.170a0220.39a13.0007.GAE@google.com/
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260523170523.1074563-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ffs_fs_kill_sb() unconditionally calls cancel_work_sync() on
ffs->reset_work when a functionfs instance is unmounted:
ffs_data_reset(ffs);
cancel_work_sync(&ffs->reset_work);
However ffs->reset_work is only ever initialized via INIT_WORK() in
ffs_func_set_alt() and ffs_func_disable(), and only on the
FFS_DEACTIVATED path. That state is reached solely by ffs_data_closed()
when the instance is mounted with the "no_disconnect" option, so for the
common case (no "no_disconnect", or mounted and unmounted without ever
being deactivated) reset_work is never initialized.
ffs_data_new() allocates the ffs_data with kzalloc_obj() and does not
initialize reset_work, and ffs_data_reset()/ffs_data_clear() do not touch
it either, so reset_work.func is left NULL. cancel_work_sync() on such a
work then trips the WARN_ON(!work->func) guard in __flush_work():
WARNING: kernel/workqueue.c:4301 at __flush_work+0x330/0x360, CPU#3: umount
Call trace:
__flush_work
cancel_work_sync
ffs_fs_kill_sb [usb_f_fs]
deactivate_locked_super
deactivate_super
cleanup_mnt
__cleanup_mnt
task_work_run
exit_to_user_mode_loop
el0_svc
On older kernels cancel_work_sync() on a zero-initialized work struct was
a silent no-op, which hid the missing initialization.
Initialize reset_work once in ffs_data_new() so it is always valid for
the lifetime of the ffs_data, and drop the now-redundant INIT_WORK()
calls from the two deactivation paths.
Fixes: 18d6b32fca38 ("usb: gadget: f_fs: add "no_disconnect" mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Tyler Baker <tyler.baker@oss.qualcomm.com>
Cc: Loic Poulain <loic.poulain@oss.qualcomm.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@oss.qualcomm.com>
Tested-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Link: https://patch.msgid.link/20260609193635.2284430-1-tyler.baker@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cdnsp_alloc_stream_info() allocates stream_info->stream_ctx_array with
cdnsp_alloc_stream_ctx(). If a later stream ring allocation or stream
mapping update fails, the error path frees the allocated stream rings
and stream_rings array, but leaves stream_ctx_array allocated.
Free the stream context array before falling through to the stream_rings
cleanup path.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://patch.msgid.link/20260622052627.696373-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In ffs_dmabuf_transfer(), a ffs_dma_fence object is kmalloc'd, with the
underlying dma_fence later initialized by dma_fence_init(), which sets
its kref counter to 1. Then, dma_resv_add_fence() gets a second
reference, and a pointer to the ffs_dma_fence is passed as the
usb_request's "context" field.
The dma-resv mechanism will manage the second reference, but the first
reference is never properly released; the ffs_dmabuf_cleanup() function
decreases the reference count, but only to balance with the reference
grab in ffs_dmabuf_signal_done().
The code will then slowly leak memory as more ffs_dma_fence objects are
created without being ever freed.
Address this issue by transferring ownership of the fence to the DMA
reservation object, by calling dma_fence_put() right after
dma_resv_add_fence(). The ffs_dma_fence then gets properly discarded
after being signalled.
Fixes: 7b07a2a7ca02 ("usb: gadget: functionfs: Add DMABUF import interface")
Cc: stable <stable@kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20260609152905.729328-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The existing implementation assigned these flags backwards, configuring
the partner's DisplayPort role to match the port's role instead of
complementing it.
This prevents proper configuration during DP altmode activation, often
causing `pin_assignment` to remain 0 in `dp_altmode_configure()` and
resulting in VDM negotiation failures:
[ 583.328246] typec port1.1: VDM 0xff01a150 failed
Additionally, the fix ensures that the `pin_assignment` sysfs attribute
displays the correct values.
Cc: stable <stable@kernel.org>
Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260601142837.3240207-1-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The allocated device name is never freed on early ULPI device
registration failures.
Fix this by initialising the device structure earlier and releasing the
initial reference whenever registration fails.
Fixes: 289fcff4bcdb ("usb: add bus type for USB ULPI")
Cc: stable <stable@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260608145803.69360-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_stor_adjust_quirks() parses the usb-storage.quirks module
parameter into a new flag set and then applies it with the quirk
mask to override built-in flags.
The mask is meant to cover the flags that can be overridden by
the module parameter. The 'k' quirk character sets US_FL_NO_SAME,
but US_FL_NO_SAME is not included in the mask.
As a result, the module parameter can set US_FL_NO_SAME, but it
cannot clear a built-in US_FL_NO_SAME flag by providing an override
entry that omits 'k'.
Add US_FL_NO_SAME to the mask so that the module parameter can
override it in the same way as the other supported flags.
Fixes: 8010622c86ca ("USB: UAS: introduce a quirk to set no_write_same")
Cc: stable <stable@kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://patch.msgid.link/3BCE5880F9A45C2E+20260602053842.2920137-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The VIA Labs, Inc. USB 2.0 hub controller (2109:2817),
found in a KVM switch, fails to enumerate high-power devices during
cold boot and system restart.
Applying the kernel parameter
usbcore.quirks=2109:2817:k
resolves the issue.
Enumeration failure log:
usb 1-1.2.3: device descriptor read/64, error -32
usb 1-1.2.3: Device not responding to setup address.
usb 1-1.2.3: device not accepting address 11, error -71
usb 1-1.2-port3: unable to enumerate USB device
Add USB_QUIRK_NO_LPM for this device.
Signed-off-by: Rodrigo Lugathe da Conceição Alves <lugathe2@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260603113626.395612-1-lugathe2@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Samsung T5 EVO Portable SSD (04e8:6200) exhibit two forms of
link instability when USB Link Power Management is enabled:
1. The units fail to initialize properly on first detection,
resulting in a lockup in the drive where it must be power cycled
or the kernel will not recognize the presence of the device.
2. If used for sustained operations (small amounts of continuous
data are transferred to the unit) then the unit will "hiccup"
after roughly 8 hours of use and will disconnect and reconnect.
This has a certain probability of triggering the first issue,
but also causes mount points to become invalid since the device
gets issued a new letter.
Signed-off-by: Erich E. Hoover <erich.e.hoover@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260602204508.48856-1-erich.e.hoover@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Uniden BC125AT radio scanner has a USB interface which fails to work
with the cdc_acm driver:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
cdc_acm 1-1:1.0: Zero length descriptor references
cdc_acm 1-1:1.0: probe with driver cdc_acm failed with error -22
usbcore: registered new interface driver cdc_acm
Adding the NO_UNION_NORMAL quirk for the device fixes the issue:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
cdc_acm 1-1:1.0: ttyACM0: USB ACM device
usbcore: registered new interface driver cdc_acm
`lsusb -v` of the device:
Bus 001 Device 002: ID 1965:0017 Uniden Corporation BC125AT
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0 [unknown]
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1965 Uniden Corporation
idProduct 0x0017 BC125AT
bcdDevice 0.01
iManufacturer 1 Uniden America Corp.
iProduct 2 BC125AT
iSerial 3 0001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0030
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 [unknown]
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Jared Baldridge <jrb@expunge.us>
Cc: stable <stable@kernel.org>
Link: https://patch.msgid.link/20260530221959.612526-1-jrb@expunge.us
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow xHC to runtime suspend if DbC is in 'enabled' state for over
15 seconds without a connect.
Idea is that every time we go to 'enabled' state we make sure DbC runtime
pm usage is '1' and save a timestamp. if the event loop still finds DbC in
enabled state 15 seconds later then it decrease DbC runtime pm usage by
calling pm_runtime_put().
Enabled state is reached either when DbC is enabled by userspace or a
connected/configured DbC is disconnected.
When a connect is detected we make sure DbC usage count is 1.
If DbC has been in 'enabled' state for 15 seconds and DbC usage is
decreased to 0 by pm_runtime_put, then the whole xHC controller may
runtime suspends to PCI D3 state if no other devices are using it
DbC sysfs file will show 'suspended' when xHC is suspended and will wake up
and enable DbC at cable connect, or when user writes 'enable' to the file.
This patch was originally part of a larger DbC series, but dropped before
the series was submitted to 7.2-rc1. The series has a locking issue in
commit 520058b73ba3 ("xhci: dbc: serialize enabling and disabling dbc")
which is also resolved by this patch
Fixes: 520058b73ba3 ("xhci: dbc: serialize enabling and disabling dbc")
Reported-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Closes: https://lore.kernel.org/linux-usb/9ce24ff5-efab-4089-92d7-709862d68e6d@intel.com
Tested-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://patch.msgid.link/20260616100916.2234205-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lc variable took it's name as an acronym from struct
intel_dp_link_config. Rename the variable into lce since the struct was
renamed into intel_dp_link_config_entry.
Signed-off-by: Michał Grzelak <michal.grzelak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20260623224619.1949975-30-michal.grzelak@intel.com
|
|
ACPI_TAD_AC_WAKE is a non-zero bit definition, so testing the macro
itself is always true. As a result, every TAD device is initialized as
a system wakeup device, including RTC-only devices and devices whose
wake capability bits were cleared because _PRW is absent.
Test the capability value returned by _GCP instead. This keeps
RTC-only TAD devices usable without advertising a wakeup capability
that the firmware does not provide.
Fixes: 6c711fde3a1c ("ACPI: TAD: Support RTC without wakeup")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/961A84FF37B50665+20260625132903.2840457-1-raoxu@uniontech.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
sh_msiof_spi_reset_regs() asserts TX/RX reset and polls until the reset
bits clear, but the poll result is ignored. sh_msiof_transfer_one() can
therefore continue programming a transfer after the controller did not
leave reset.
Return the reset poll result from the helper and abort the transfer on
timeout, matching the existing transfer path's error-return style.
Fixes: fedd6940682a ("spi: sh-msiof: Add reset of registers before starting transfer")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260623135834.55442-1-pengpeng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CONFIG_RTC_DRV_DS1307_HWMON macro was removed in favor of
CONFIG_HWMON in commit 6b583a64fd1e ("rtc: ds1307: simplify hwmon
config"), but a reference to it remained in a comment. Correct this
reference.
Discovered while searching for CONFIG_* symbols referenced in code but
not defined in any Kconfig file.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260610054723.261008-1-enelsonmoore@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
It was reported that suspend-then-hibernate stopped working with modern
systemd versions on AMD Cezanne systems. The reason for this breakage
was because systemd switched to using alarmtimer instead of the wakealarm
sysfs file.
On AMD Cezanne systems, amd_pmc_verify_czn_rtc() programs a secondary
timer with the alarm time. This was introduced by
commit 59348401ebed ("platform/x86: amd-pmc: Add special handling for
timer based S0i3 wakeup"). However, this function uses rtc_read_alarm(),
which only reads the aie_timer, not the next expiring timer from the
timerqueue.
When both alarmtimer and wakealarm are active, the first expiring timer
might be the alarmtimer, but amd_pmc_verify_czn_rtc() would only see
the aie_timer, potentially missing the earlier alarm.
Switch to rtc_read_next_alarm() to read whichever timer will fire next.
Also handle -ENOENT (no alarm pending) explicitly as a non-error case.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3591
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://patch.msgid.link/20260521043714.1022930-3-mario.limonciello@amd.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add arch_phys_wc_del() on error path to keep the
write-combining setup balanced when later probe
steps fail.
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Fix trivial typo
Link: https://patch.msgid.link/20260624204223.1479003-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-06-22 (ice, i40e, e1000e)
For ice:
Dawid changes call to release control VSI during reset to prevent
leaking it.
Lukasz fixes flow control error check to check value rather than treat
is as bitmap values.
Paul makes link related errors non-fatal to probe to allow for recovery
in certain NVM update situations.
Marcin moves netif_keep_dst() to only be called once when entering
switchdev mode.
ZhaoJinming adds a cleanup path for ice_dpll_init_info() to prevent
memory leaks on error path.
For i40e:
Mohamed Khalfella corrects argument passed in macro to match the
one provided to the macro.
For e1000e:
Dima resolves power state issues by adjusting value of PLL clock gate
and re-enabling K1; a quirk table is added to keep it off for known bad
systems.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Reconfigure PLL clock gate timeout and re-enable K1 on Meteor Lake
i40e: Fix i40e_debug() to use struct i40e_hw argument
ice: dpll: fix memory leak in ice_dpll_init_info error paths
ice: dpll: set pointers to NULL after kfree in ice_dpll_deinit_info
ice: call netif_keep_dst() once when entering switchdev mode
ice: fix ice_init_link() error return preventing probe
ice: fix AQ error code comparison in ice_set_pauseparam()
ice: fix FDIR CTRL VSI resource leak in ice_reset_all_vfs()
====================
Link: https://patch.msgid.link/20260622220059.2471844-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current irq definition of the wake irq and the lpi irq
is wrong, replace them with the right number and name.
Fixes: 30f0ba420ed3 ("net: stmmac: Add glue layer for Spacemit K3 SoC")
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260623074637.503864-3-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current MII interface register definition from the vendor is wrong,
use the right number for the macro. Also, correct the interface mask
in spacemit_set_phy_intf_sel() so it can update the register with the
right number
Fixes: 30f0ba420ed3 ("net: stmmac: Add glue layer for Spacemit K3 SoC")
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260623074637.503864-2-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mac->phy_node is acquired via of_parse_phandle() in spl2sw_probe() and
stored in the mac private data, transferring ownership of the
device_node reference to mac. On driver removal, spl2sw_phy_remove()
disconnects the PHY but never drops that reference, so each
probe-then-remove cycle leaks one of_node refcount per port permanently.
Drop the reference after phy_disconnect(). While at it, remove the
redundant inner "if (ndev)" check; comm->ndev[i] was just verified
non-NULL on the line above.
Compile-tested only; no SP7021 hardware available.
Fixes: fd3040b9394c ("net: ethernet: Add driver for Sunplus SP7021")
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/f3bdd4c91f3e2269b4e256075f9dc70808b1b8e9.1782195965.git.shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gem_init_one() calls gem_remove_one() when register_netdev() fails.
gem_remove_one() unregisters and frees resources owned by the net_device,
including the DMA block, MMIO mapping, PCI regions, and the net_device
itself. gem_init_one() then falls through to its own cleanup labels and
frees the same resources again.
Keep the register_netdev() error path in gem_init_one(): clear drvdata so
PM/remove paths do not see a half-registered device, remove the NAPI
instance added during probe, and let the existing cleanup labels release
the resources once.
The issue was found by a local static-analysis checker for probe error
paths. The reported path was manually inspected before sending this fix.
Compile-tested with CONFIG_SUNGEM=y. Runtime testing was not performed
because no sungem hardware is available.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260623025759.3468566-1-ruoyuw560@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Configurations with mlx5 built-in but macsec=m fail to link:
x86_64-linux-ld: drivers/infiniband/hw/mlx5/macsec.o: in function `mlx5r_add_gid_macsec_operations':
macsec.c:(.text+0x77d): undefined reference to `macsec_netdev_is_offloaded'
x86_64-linux-ld: drivers/infiniband/hw/mlx5/macsec.o: in function `mlx5r_del_gid_macsec_operations':
macsec.c:(.text+0xe81): undefined reference to `macsec_netdev_is_offloaded'
Fix the dependency so this configuration cannot happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20260622124229.2444502-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 *
KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that
skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can
deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or
leave a short trailing remainder on a later loop iteration. Either case
underflows usb_packet_length to about 65530.
That bypasses the usb_packet_length < ether_packet_length truncation path.
The device-supplied ether_packet_length, a le16 up to 65535 read from
header_start[2], then drives a memcmp() and the following skb_trim() and
skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10,
which is 14000 bytes. That is an out of bounds read.
Require both the start and end framing headers to be present before
subtracting them, on every loop iteration.
Fixes: d40261236e8e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Cc: stable@vger.kernel.org
Signed-off-by: Maoyi Xie <maoyixie.tju@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/178211531778.2216480.12637613349790980750@maoyixie.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Even with both paths gated on gs->gro_hint, geneve_gro_complete()
re-derives the inner dispatch type and length from the packet and the
current gs->gro_hint, independently of geneve_gro_receive(). The two can
disagree if gs->gro_hint flips under a concurrent geneve_quiesce()/
geneve_unquiesce() (sk_user_data is NULL across a synchronize_net()), or if
the re-read option bytes differ from the ones receive parsed.
geneve_gro_receive() already records the inner network header position in
NAPI_GRO_CB()->inner_network_offset. Have geneve_gro_complete() compute the
offset it is about to dispatch at, adding ETH_HLEN in the ETH_P_TEB case
where eth_gro_complete() steps over the inner MAC header, and bail out if
it lands past inner_network_offset.
Use a lower bound rather than exact equality: between gh_len and the inner
L3 header, geneve_gro_receive() may also have pulled an inner VLAN tag
(vlan_gro_receive() advances the recorded offset past it), which only moves
inner_network_offset further out. A valid frame therefore always satisfies
inner_nh <= inner_network_offset, while a gh_len inflated by a hint
gro_receive() did not honour dispatches past the validated inner header,
i.e. the out-of-bounds completion. Only the latter is rejected.
Fixes: fd0dd796576e ("geneve: use GRO hint option in the RX path")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Weiming Shi <bestswngs@gmail.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Link: https://patch.msgid.link/20260618032622.484720-2-xmei5@asu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
geneve_gro_receive() reads the GRO hint through geneve_sk_gro_hint_off(),
which honours it only when the socket enabled IFLA_GENEVE_GRO_HINT
(gs->gro_hint). geneve_gro_complete() instead calls the low-level
geneve_opt_gro_hint_off() and acts on the hint unconditionally.
On a tunnel without the hint, receive aggregates the frames as plain
ETH_P_TEB while complete still honours an attacker-supplied hint option: it
inflates gh_len by gro_hint->nested_hdr_len (u8) and redirects the dispatch
type, so the inner gro_complete handler runs at nhoff + gh_len, an offset
receive never pulled nor validated, reading out of bounds of the skb head:
BUG: KASAN: slab-out-of-bounds in ipv6_gro_complete (net/ipv6/ip6_offload.c:196)
Read of size 1 at addr ffff88800fe91980 by task exploit/153
ipv6_gro_complete (net/ipv6/ip6_offload.c:196)
geneve_gro_complete (drivers/net/geneve.c:965)
udp_gro_complete (net/ipv4/udp_offload.c:940)
inet_gro_complete (net/ipv4/af_inet.c:1621)
__gro_flush (net/core/gro.c:306)
Gate the complete path on gs->gro_hint too via geneve_sk_gro_hint_off(), so
both paths agree. Tunnels that enable the hint are unaffected.
Fixes: fd0dd796576e ("geneve: use GRO hint option in the RX path")
Reported-by: Weiming Shi <bestswngs@gmail.com>
Reported-by: Kyle Zeng <kylebot@openai.com>
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Link: https://patch.msgid.link/20260618032622.484720-1-xmei5@asu.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
