| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is no policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT, so
the parse infrastructure does not enforce a minimum length for the event
struct. Additionally, the num_vdevs field is taken directly from firmware
and used as a loop bound over the vdev_ids array without checking that it
fits within the TLV payload. Either condition can cause an out-of-bounds
read.
Add a TLV policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT so
the parse infrastructure enforces a minimum length for the fixed-size event
struct. Add a helper ath11k_wmi_tlv_data_len() to recover the payload
length of a parsed TLV from the header preceding its data pointer. Use it
in ath11k_wmi_process_csa_switch_count_event() to bound num_vdevs before
the loop.
Compile tested only.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260724-ath12k_wmi_process_csa_switch_count_event-cleanup-v2-2-02a45d7246c0@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
There is no policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT, so
the parse infrastructure does not enforce a minimum length for the event
struct. Additionally, the num_vdevs field is taken directly from firmware
and used as a loop bound over the vdev_ids array without checking that it
fits within the TLV payload. Either condition can cause an out-of-bounds
read.
Add a TLV policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT so
the parse infrastructure enforces a minimum length for the fixed-size event
struct. Add a helper ath12k_wmi_tlv_data_len() to recover the payload
length of a parsed TLV from the header preceding its data pointer. Use it
in ath12k_wmi_process_csa_switch_count_event() to bound num_vdevs before
the loop.
Compile tested only.
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Assisted-by: Claude:claude-sonnet-4-6
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260724-ath12k_wmi_process_csa_switch_count_event-cleanup-v2-1-02a45d7246c0@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The mismatch would pop up when building the kernel with W=1.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Link: https://patch.msgid.link/20260720-vm_bind_checks-v6-2-c2c7dbe93a73@collabora.com
Signed-off-by: Steven Price <steven.price@arm.com>
|
|
When a VM is created, caller has to specify the range of the address space
carve-out set aside for mapping kernel BO's. That means vm_bind mappings of
UM-exposed BO's should not intersect with that region, but at the moment
we're not checking this.
At first, I thought of giving these values to drm_gpuvm_init() through its
reserve_{offset, range} arguments, but it turns out that is meant for VM
address spans that are not managed through the usual drm_gpuvm split/merge
circuit, so storing the end of the user VA range at VM creation time and
doing a quick check in the vm_bind ioctl path was the simplest workaround.
The new check also makes sure vm_bind range doesn't overflow the size of a
64-bit unsigned integer. That was already being done further down the call
stack inside drm_gpuvm_sm_map -> drm_gpuvm_range_valid, but it's best to
fail early in the driver before GPUVM functions are invoked so that we
won't waste time allocating vm_bind context resources.
Fixes: 12cf826bf1dd ("drm/panthor: Support sparse mappings")
Fixes: 647810ec2476 ("drm/panthor: Add the MMU/VM logical block")
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20260720-vm_bind_checks-v6-1-c2c7dbe93a73@collabora.com
Signed-off-by: Steven Price <steven.price@arm.com>
|
|
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_threaded_irq(). During
removal, spi_bitbang_stop() only unregisters the controller; the
subsequent spi_controller_put() then frees the controller together with
its embedded davinci_spi devdata, which is the IRQ handler's dev_id.
The devm_request_threaded_irq() release action (free_irq()), which
drains the handler, does not run until after .remove() returns. A late
or latched interrupt can therefore reach davinci_spi_irq() and
dereference already-freed memory.
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
The clock is acquired with devm_clk_get_enabled(), which is registered
after the IRQ and thus released before it by the devres LIFO order.
Drain the interrupt explicitly with devm_free_irq() before disabling the
controller so that a late interrupt cannot access the registers of a
clock-gated controller.
This issue was found by an in-house static analysis tool.
Fixes: 5b3bb5963ff2 ("spi: davinci: Use devm_*() functions")
Assisted-by: Codex:gpt-5.6
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260719010014.3163356-2-fanwu01@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
iface_fw_to_cpu_addr() only checks that the firmware-provided MCU virtual
address points inside the shared section. The returned pointer is later
used as a full firmware interface structure, so accepting an address near
the end of the shared section can still lead to out-of-bounds accesses.
Pass the expected object size to iface_fw_to_cpu_addr() and reject ranges
that do not fit entirely in the shared section.
Fixes: 2718d91816ee ("drm/panthor: Add the FW logical block")
Cc: stable@vger.kernel.org
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20260720114918.15973-1-osama.abdelkader@gmail.com
|
|
nvmet_param_mdts_store() accepts any integer that kstrtoint() can parse
and stores it directly into port->mdts. The value is only range-checked
later, when the port is enabled: nvmet_enable_port() silently resets
port->mdts to 0 if it is negative or greater than NVMET_MAX_MDTS.
As a result, writing e.g. "mdts=1000" succeeds and reading the attribute
back returns 1000, yet enabling the port quietly turns it into 0. This
is confusing and hides the invalid input from the user.
Validate the value against [0, NVMET_MAX_MDTS] in the store handler and
reject anything out of range with -EINVAL, so the error is reported at
write time and port->mdts never holds a value the port cannot use.
Fixes: 0a5a94648627 ("nvmet: introduce new mdts configuration entry")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
quirks_param_set() reuses 'err', which param_set_copystring() left as 0,
as the return value of the whole function. When nvme_parse_quirk_entry()
fails to parse a field, the code jumps to out_free_qlist and returns that
stale 0, so a malformed quirks= parameter is silently accepted as valid.
Set err to -EINVAL before jumping out on a parse failure.
Fixes: 7bb8c40f5ad8 ("nvme: add support for dynamic quirk configuration via module parameter")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
__nvme_fc_init_request() maps cmd_iu and then rsp_iu for DMA. If the
rsp_iu mapping fails, the original code only recorded the error and fell
through: it left the already-mapped cmd_iu unmapped and still marked the
op as FCPOP_STATE_IDLE before returning. Since blk-mq does not call
.exit_request() when .init_request() fails, the cmd_iu mapping is leaked
for every op whose rsp_iu mapping fails.
Jump to an error path on rsp_iu mapping failure that unmaps cmd_iu and
returns the error without marking the op idle, so it stays in the
FCPOP_STATE_UNINIT state set by the initial memset().
Fixes: e399441de911 ("nvme-fabrics: Add host support for FC transport")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
nvmet_execute_get_log_page_rmi() leaves 'status' holding NVME_SC_SUCCESS
(set by the successful nvmet_req_find_ns() call) when the kzalloc() for
the log buffer fails. It then jumps to the out label and completes the
request with a success status, so the host is told the command succeeded
while no data was transferred.
Initialize 'status' to NVME_SC_INTERNAL, matching the smart log handler,
so an allocation failure is reported as an internal error.
Fixes: 5fd075cdaf36 ("nvmet: implement rotational media information log")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/drivers
Samsung SoC drivers for v7.3
1. Fix very old leak of OF node in PMU driver.
2. Few cleanups and new bindings for ExynosAutov920 HSI0 syscon.
* tag 'samsung-drivers-7.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: exynos-pmu: Narrow allowed reboot modes
dt-bindings: samsung: exynos-pmu: Restrict children with unevaluatedProperties
dt-bindings: soc: samsung: exynos-sysreg: Add hsi0 for ExynosAutov920
soc: samsung: exynos-pmu: fix of_node refcount leak in exynos_get_pmu_regmap()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into soc/drivers
Memory controller drivers for v7.3
1. Few improvements: STM32 OMM, Tegra MC and JZ4780-nemc.
2. Refactor Tegra MC interconnect code to better represent actual
hardware in multi-socket NUMA cases.
* tag 'memory-controller-drv-7.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: jz4780-nemc: Use dev_err_probe() for clock error
memory: tegra: Guard against NULL mc_regs in IRQ handler
memory: tegra: add multi-socket support to the memory interconnect
memory: stm32_omm: initialize ret in stm32_omm_set_amcr
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
panthor_fw_read_build_info() checks whether the metadata range fits in the
firmware image with hdr.meta_start + hdr.meta_size. Both fields are u32, so
the addition can wrap and let an out-of-bounds range pass validation.
The function also reads the "git_sha: " prefix without first checking that
the metadata is long enough, and meta_size == 0 can underflow the NULL
terminator index.
Use subtraction-based bounds checking and reject metadata that is too short
to contain the expected prefix and trailing NULL byte.
Fixes: 2718d91816ee ("drm/panthor: Add the FW logical block")
Cc: stable@vger.kernel.org
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20260720113212.11981-1-osama.abdelkader@gmail.com
|
|
Instead of defining the wait values for each driver, use common values
defined in the core pci.h header file. Note that while most drivers use
the usleep_range(), it looks like these were mostly cargo culted and
msleep() is a better choice given the fixed delay that the specification
calls for. Convert all drivers to msleep() and use the existing
definition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20260716-tegra264-pcie-v8-3-23e51589229b@nvidia.com
|
|
ovpn_fill_info emits IFLA_OVPN_MODE inside IFLA_INFO_DATA, but
ovpn_link_ops does not provide a get_size callback. Consequently,
rtnetlink's size estimate for ovpn link messages does not include the
nested mode attribute.
Available skb tailroom may hide this mismatch. When the remaining space
is insufficient, however, ovpn_fill_info returns -EMSGSIZE and message
construction fails.
Add the callback and account for IFLA_OVPN_MODE.
Fixes: c2d950c4672a ("ovpn: add basic interface creation/destruction/management routines")
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
|
|
Commit 7aa1aa6ecec2 ("QE: Move QE from arch/powerpc to drivers/soc")
moved QE into drivers/soc including gpio.c but left CONFIG_QE_GPIO
in powerpc's Kconfig.
Move it to SoC as well as it is the only place it is used:
drivers/soc/fsl/qe/Makefile:obj-$(CONFIG_QE_GPIO) += gpio.o qe_ports_ic.o
include/soc/fsl/qe/qe.h:#ifdef CONFIG_QE_GPIO
include/soc/fsl/qe/qe.h:#endif /* CONFIG_QE_GPIO */
There is also a dependency in USB subsystem for CONFIG_USB_FHCI_HCD:
drivers/usb/host/Kconfig: depends on QE_GPIO && QUICC_ENGINE
Because that USB driver selects CONFIG_FSL_GTM which is specific to
powerpc, it has to depend on CONFIG_PPC.
Acked-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://lore.kernel.org/r/9a7131d15a94e2017877e628f0e97f9aa2e0aae9.1785140877.git.chleroy@kernel.org
Signed-off-by: Christophe Leroy (CS GROUP) <chleroy@kernel.org>
|
|
On a non-range clear, curs.size is never set, so the segment test
(next - va_curs_start > curs->size) returns false for every level > 0
before the clear_pt short-circuit is reached. The clear then descends to
level 0 instead of forming a huge zero-leaf, wasting page tables and
risking -ENOMEM on unbind.
Move the null-VMA, purged-BO and clear_pt short-circuits above the
curs->size test. The bind path always sets curs.size, so it is unaffected.
v2
- Also set curs.size on the clear path so the cursor stays meaningful
during the walk. clear_pt is only reached with range == NULL, so assert
that invariant. (Matthew Brost)
Cc: Matthew Brost <matthew.brost@intel.com>
Fixes: 5b658b7e89c3 ("drm/xe: Clear scratch page on vm_bind")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260728055916.593707-2-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
(cherry picked from commit 04eeeb45cb61b8a3e9d785003457e550c920ba49)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Trace point pvr_job_submit_fw() is used to trace job submission to
the FW. Currently it is recorded when a command is written to the Client
circular buffer.
Move trace recording after writing command to the Kernel circular buffer to
better represent command submission to the FW.
Fixes: c1079aebb4de ("drm/imagination: Add support for trace points")
Signed-off-by: Brajesh Gupta <brajesh.gupta@imgtec.com>
Reviewed-by: Alessio Belle <alessio.belle@imgtec.com>
Link: https://patch.msgid.link/20260724-b4-tracepoint-fix-v3-1-8f8e5e8179d3@imgtec.com
Signed-off-by: Alessio Belle <alessio.belle@imgtec.com>
|
|
intel_dp_hdmi_sink_max_frl() limits the sink's max FRL rate by its
DSC max FRL rate whenever the sink supports DSC 1.2.
However, the DSC max FRL rate (HF-VSDB DSC_Max_FRL_Rate) only applies
to compressed video transport, which requires a DSC 1.2 encoder in
the PCON (configured via intel_dp_pcon_dsc_configure()).
Without such an encoder the HDMI link always carries uncompressed
video, for which the regular Max_FRL_Rate is the correct limit.
Applying the DSC limit unconditionally trains the FRL link at a lower
rate than both the PCON and the sink support.
E.g. an LG OLED G4 (Max_FRL_Rate 48 Gbps, DSC_Max_FRL_Rate 24 Gbps)
behind a Synaptics VMM7100 PCON (PCON max FRL bw 48 Gbps, no DSC
encoder):
Sink max rate from EDID = 24 Gbps
FRL trained with : 24 Gbps
while Windows/macOS train the same hardware at 40/48 Gbps.
The too low FRL rate needlessly constrains the formats available to
the sink.
Only apply the sink's DSC max FRL rate if the PCON has a DSC 1.2
encoder, matching the gate in intel_dp_pcon_dsc_configure().
PCONs with a DSC encoder keep the current conservative behavior,
since the link is trained once and compressed transport may be used
for any subsequent mode.
With this the setup above trains at 48 Gbps.
Tested on PTL (xe) with the above PCON/sink combo.
Fixes: 10fec80b48c5 ("drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Alexander Kaplan <alexander.kaplan@sms-medipool.de>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260718105207.5565-3-alexander.kaplan@sms-medipool.de
(cherry picked from commit 71b57dd92f94569dca4bdf883fbd8ca5d4ed4bae)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
isert_login_recv_done() records how many bytes the HCA actually placed in
the login buffer, but nothing compares that against the length the login
PDU's BHS declares. isert_rx_login_req() copies min(login_req_len,
MAX_KEY_VALUE_PAIRS) bytes into login->req_buf, and the login code then
reads the declared length back out of that buffer - for the first PDU in
iscsi_target_locate_portal(),
payload_length = ntoh24(login_req->dlength);
tmpbuf = kmemdup_nul(login->req_buf, payload_length, GFP_KERNEL);
and for the ones after it in iscsi_decode_text_input(), reached from
iscsi_target_do_login().
login->req_buf is a fixed MAX_KEY_VALUE_PAIRS (8192) byte allocation, so
an initiator that declares more than it sends reads off the end of it,
before authentication and with the length under its control:
BUG: KASAN: slab-out-of-bounds in kmemdup_nul+0x43/0x80
Read of size 8193 at addr ffff8881056a8000 by task iscsi_np/167
__asan_memcpy+0x23/0x60
kmemdup_nul+0x43/0x80
iscsi_target_locate_portal+0x48d/0x1180
iscsi_target_login_thread+0x19a9/0x3350
Allocated by task 167:
__kmalloc_cache_noprof+0x158/0x370
iscsi_target_login_thread+0x971/0x3350
which belongs to the cache kmalloc-8k of size 8192
allocated 8192-byte region
Falsifying the second login PDU instead reaches the other reader, on the
same buffer:
BUG: KASAN: slab-out-of-bounds in kmemdup_nul+0x43/0x80
Read of size 8193 at addr ffff888104d10000 by task kworker/1:1/50
Workqueue: isert_login_wq iscsi_target_do_login_rx
__asan_memcpy+0x23/0x60
kmemdup_nul+0x43/0x80
iscsi_decode_text_input+0xc6/0x11c0
iscsi_target_do_login+0x261/0x1470
iscsi_target_do_login_rx+0x51d/0x7d0
iscsit over TCP is not exposed: iscsit_get_login_rx() validates the
declared length with iscsi_target_check_login_request() and then reads
exactly that many bytes off the socket, so the declared length governs
how much arrives rather than how much is copied out of an already-filled
buffer. isert does not call iscsi_target_check_login_request() at all.
Reject a login PDU whose declared DataSegmentLength exceeds what was
received, in both paths that reach isert_rx_login_req():
isert_get_login_rx() for the first login PDU and isert_login_recv_done()
for the ones after it. dlength <= login_req_len is allowed because the
received count can include up to three bytes of iSCSI padding.
Once the check is in place the copy out can no longer exceed the copy in:
the posted login SGE is ISER_RX_PAYLOAD_SIZE, so login_req_len cannot
exceed MAX_KEY_VALUE_PAIRS and the min() in isert_rx_login_req() is
login_req_len.
Like the existing short-PDU check added by 29e7b925ae6d, the reject in
isert_login_recv_done() returns without completing login_req_comp, so a
malformed subsequent PDU leaves the login to be torn down by the login
timer rather than failing immediately. The first-PDU path returns an
error and fails straight away.
Reproduced on 7.2.0-rc4 with soft-RoCE (rdma_rxe) under KASAN, using an
initiator that sends the real key=value payload while declaring 8193 in
the BHS, on the first login PDU and on the second in separate runs. The
reported read size tracks the declared value exactly; 16384 and 61440
behave the same. Unpatched 3 of 3 runs report on each of the two paths,
patched 0 of 3 on both, run alternately in a single session, and a normal
login still completes on the patched build.
Fixes: b8d26b3be8b3 ("iser-target: Add iSCSI Extensions for RDMA (iSER) target driver")
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Link: https://patch.msgid.link/20260726163931.971063-3-yhlee@isslab.korea.ac.kr
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
isert_recv_done() hands each received PDU to the opcode handlers without
ever looking at wc->byte_len, the number of bytes the HCA actually placed
in the receive descriptor. The handlers then copy that many bytes - the
data-segment length the initiator declared in the BHS
(ntoh24(hdr->dlength), via the derived unsol_data_len / imm_data_len) -
out of the fixed-size descriptor:
isert_handle_iscsi_dataout():
sg_copy_from_buffer(sg_start, sg_nents, isert_get_data(rx_desc),
unsol_data_len);
isert_handle_scsi_cmd():
sg_copy_from_buffer(cmd->se_cmd.t_data_sg, sg_nents,
isert_get_data(rx_desc), imm_data_len);
Because the declared length is never checked against wc->byte_len, an
initiator can declare a data segment larger than the bytes it actually
sent (and larger than the descriptor) and cause an out-of-bounds read of
the receive buffer.
Nothing upstream of isert closes this door:
- __iscsit_check_dataout_hdr() bounds the inbound payload against
conn_ops->MaxXmitDataSegmentLength (MXDSL) - a transmit parameter,
used here for the inbound check.
- iscsi_set_connection_parameters() sets
ops->MaxXmitDataSegmentLength = ops->TargetRecvDataSegmentLength;
and TARGETRECVDATASEGMENTLENGTH is absent from the min()-clamp list in
iscsi_check_acceptor_state(), so the value the initiator declares is
adopted verbatim (type range 512..16777215). The initiator effectively
raises its own ceiling.
- isert never clamps the negotiated value to its own fixed receive
descriptor (ISER_RX_SIZE, 9216 bytes), so the target core's bound and
the descriptor size are unrelated.
The imm_data_len == data_len path is more than an over-read: it aliases
the receive descriptor via sg_set_buf() and passes it to the backend as
the data source for the SCSI WRITE, so an over-declared length causes heap
contents past the descriptor to be written through the backend to the
backing store. The backend is the victim of the oversized scatterlist
isert hands it, not the cause; no read-back of the written bytes was
demonstrated.
Trigger: after login completes (full feature phase), an initiator that has
declared a large TargetRecvDataSegmentLength and a FirstBurstLength that
permits unsolicited/immediate data sends a PDU whose declared data-segment
length exceeds what was received. With KASAN:
BUG: KASAN: slab-out-of-bounds in sg_copy_buffer+0x150/0x1c0
Read of size 4096 at addr ffff888109720800 by task kworker/1:0H/25
Workqueue: ib-comp-wq ib_cq_poll_work
Call Trace:
sg_copy_buffer+0x150/0x1c0
isert_recv_done+0xba6/0x2390
__ib_process_cq+0xe1/0x390
ib_cq_poll_work+0x46/0x150
isert_recv_done+0xba6 resolves to isert_handle_iscsi_dataout()
(ib_isert.c:1160), inlined through isert_rx_opcode().
Validate wc->byte_len against the framing in isert_recv_done() before the
PDU reaches any handler, and reinstate the connection if it is short.
Because the test compares without subtracting the header length, it also
rejects PDUs shorter than the iSER and iSCSI headers, which would otherwise
be parsed out of stale descriptor contents. The login handler rejects PDUs
shorter than ISER_HEADERS_LEN (commit 29e7b925ae6d ("IB/isert: Reject login
PDUs shorter than ISER_HEADERS_LEN")) but does not bound the declared
length either; that is fixed in the next patch. The data handlers had no
length check at all.
isert reads the data segment from a fixed offset: isert_get_data()
returns the iSER header plus ISER_HEADERS_LEN and makes no adjustment for
an AHS. The bytes the handlers touch are therefore exactly
[ISER_HEADERS_LEN, ISER_HEADERS_LEN + dlength), and comparing that sum
against wc->byte_len bounds precisely the region that is read. An AHS
term would only make the test stricter without bounding anything further,
and cannot cause a false reject: a PDU carrying an AHS is longer, not
shorter.
This is a memory-safety fix that verifies the bytes that were actually
received; it does not touch RFC 7145 length negotiation and is not the
MaxXmitDataSegmentLength negotiation redesign raised in the 2017 "[Query]
iSER-Target: QP errors observed on increasing MaxXmitDataSegmentLength"
discussion. That redesign is explicitly out of scope here.
The patched kernel rejects the malformed DataOut PDU and both
immediate-data variants with "PDU declares ... bytes were received" and
continues to pass normal traffic with no regression.
Reproduced with soft-RoCE (rdma_rxe) and a raw rdma_cm/ibv initiator; no
kernel-side test hooks were needed.
Fixes: b8d26b3be8b3 ("iser-target: Add iSCSI Extensions for RDMA (iSER) target driver")
Signed-off-by: Yehyeong Lee <yhlee@isslab.korea.ac.kr>
Link: https://patch.msgid.link/20260726163931.971063-2-yhlee@isslab.korea.ac.kr
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Pro 360
The Samsung Galaxy Book5 Pro 360 (960QHA) has an upside-down mounted
OV02E10 sensor. The 180 degree rotation is reported in neither the SSDB
nor the _PLD for the sensor (both report a rotation of 0 degrees), so
the image is rendered upside-down in userspace.
Add a DMI quirk entry for this laptop so that the sensor fwnode gets a
"rotation" property of 180 and userspace (e.g. libcamera) can
compensate.
Tested on the Galaxy Book5 Pro 360: with the sensor reporting
V4L2_CID_CAMERA_SENSOR_ROTATION = 180 (verified with an equivalent
local sensor-driver quirk), libcamera renders the image upright.
Signed-off-by: Mihail Antsev <mihail.antcev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The link frequency, retrieved in cvs_csi_enable_streams(), is stored in
the icvs structure to then be used right after in csi_set_link_cfg(),
called only from the same function. Pass it as a function parameter
instead to improve readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Antti Laakso <antti.laakso@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
In mt9t112_probe(), the clock error check after devm_v4l2_sensor_clk_get()
calls PTR_ERR(priv->clk) unconditionally, before testing IS_ERR().
On a successful lookup, priv->clk is a valid pointer and calling PTR_ERR()
on it is incorrect API usage. While the comparison against -ENOENT happens
to be harmless in practice (valid kernel pointers never fall in the error
range), this is still a violation of the IS_ERR()/PTR_ERR() contract that
can mislead readers.
Restructure the check to guard PTR_ERR() inside IS_ERR(), using the
simpler != -ENOENT form to avoid an unnecessary else clause.
Signed-off-by: Uday Khare <udaykhare77@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The migration to CCI helpers made V4L2_CID_FLASH_DURATION write the
requested duration directly to OV9282_REG_STROBE_FRAME_SPAN, dropping
the conversion from microseconds to the register value.
This made flash strobes too long and produced overly bright frames.
Restore the missing calculation so flash duration is programmed
correctly again.
Fixes: 273f52f3cbec ("media: i2c: ov9282: Convert to CCI register access helpers")
Cc: Xiaolei Wang <xiaolei.wang@windriver.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
isys_notifier_init() initialises a v4l2 async notifier and then, for
each CSI-2 port, adds a remote sensor subdev to the notifier's
waiting_list via v4l2_async_nf_add_fwnode_remote(), which allocates a
sensor_async_sd descriptor and takes a fwnode reference.
If parsing or adding a later port fails, the code jumps to the
"err_parse" label, which only drops the current endpoint fwnode
reference and returns, without calling v4l2_async_nf_cleanup(). Any
descriptors already added to the notifier for earlier ports are
therefore leaked, and the caller's error path does not clean up the
notifier either.
Call v4l2_async_nf_cleanup() on the error path, matching the cleanup
already performed when v4l2_async_nf_register() fails. This is safe as
the notifier is always initialised before the loop is entered.
Fixes: a516d36bdc3d ("media: staging/ipu7: add IPU7 input system device driver")
Signed-off-by: Cong Nguyen <congnt264@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
This one was fully static, so no need to fill it in the register
function manually.
Signed-off-by: Link Mauve <linkmauve@linkmauve.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
This also removes initializing reg_write to NULL, which will help with
changing its signature in nvmem-provider[1].
Thanks to Sakari Ailus for their suggestion[2]!
[1] https://lore.kernel.org/rust-for-linux/20260716142415.28718-1-linkmauve@linkmauve.fr/
[2] https://lore.kernel.org/rust-for-linux/al3sxMUgeK49dwNs@kekkonen.localdomain/
Signed-off-by: Link Mauve <linkmauve@linkmauve.fr>
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Add 5 missing test patterns to complete the available
hardware test patterns.
The original mapping for color bars and solid color in the menu
is preserved to prevent existing userspace application and automated
vendor capture tests.
The changes were validated on a raspberry pi 5 with an imx219 sensor
using v4l2-ctl and rpicam-still.
Signed-off-by: Tharit Tangkijwanichakul <tharitt97@gmail.com>
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
Running the sensor on 10 bits mode resulted in FPS being 25% faster than
it should be. This issue did not appear in 8 bits mode. This is mostly
noticeable with libcamera as it can set a target FPS value directly.
This is caused by the V4L2_CID_PIXEL_RATE control being dynamically
changed according to the media bus code, while it should be the same
regardless of the code.
Since we already compute the pixel_clock, use it directly for
V4L2_CID_PIXEL_RATE instead.
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
The OVL adaptor registers both an aggregate driver for its child devices
and a component for the main DRM aggregate. Probe currently ignores an
error from registering the child aggregate and leaves that aggregate
registered if registering the DRM component fails. The remove callback
also leaves the DRM component registered.
These imbalances can leave component framework entries referring to a
device whose probe failed or whose driver has been detached. The aggregate
unbind callback also fails to undo component_bind_all(), leaving its child
components marked as bound when the aggregate is removed.
Check the aggregate registration result, unwind it when the component
registration fails, and unregister the component before the aggregate on
remove. Keep runtime PM enabled until both framework registrations have
been removed, and unbind all child components from the aggregate unbind
callback.
Fixes: 453c3364632a ("drm/mediatek: Add ovl_adaptor support for MT8195")
Cc: stable@vger.kernel.org # 6.4+
Co-developed-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Ijae Kim <ae878000@gmail.com>
Signed-off-by: Myeonghun Pak <mhun512@gmail.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20260721152242.47138-1-mhun512@gmail.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Commit 76255024cadb ("drm/mediatek: mtk_dsi: enable hs clock
during pre-enable") rightfully moves the HS clock enablement to
before atomic_enable(), but it's moving it to mtk_dsi_poweron(),
which is not only called in the .atomic_pre_enable() callback
for the DRM bridge, but also in the MediaTek DRM's .ddp_start()
callback, which happens way before the bridge ones.
The HS clock enablement should be done at just the right time,
otherwise some bridge chips (or some Display Driver ICs) may
not work correctly: this is seen at least with a Parade DSI to
eDP bridge (PS8640) on the MT8173 Elm Chromebook.
This resolves a regression that was seen on the aforementioned
machine, which was happening only after a suspend-resume cycle.
Cc: <stable@vger.kernel.org> # 7.1.x
Fixes: 76255024cadb ("drm/mediatek: mtk_dsi: enable hs clock during pre-enable")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Adam Thiede <me@adamthiede.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20260728153145.578404-1-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
The PCON max FRL bandwidth field lives in byte 2 of the DFP Detailed
Capability Info (DPCD 0x82 for the first DFP).
The DP standard defines the meaning of descriptor bytes 1-3 strictly
per DFP type, and for a DisplayPort type DFP all of them are
reserved, with "read all 0s" semantics (DP v2.0, section 2.12.3,
Table 2-183).
The FRL bandwidth field is an HDMI DFP extension added by the VESA
DP-to-HDMI PCON specification.
drm_dp_get_pcon_max_frl_bw() however parses the byte without checking
the DFP type, the branch presence or DETAILED_CAP_INFO_AVAILABLE.
Without the latter the port descriptors are one byte wide and
port_cap[2] is not even the right register.
All neighbouring helpers parsing the same descriptor are scoped by
the DFP type already, see for instance drm_dp_downstream_max_bpc()
reading the same byte and returning 0 for a DP type DFP.
amdgpu's DC parses the field only for HDMI(/DP++) detailed types as
well.
This is not theoretical.
A Synaptics VMM7100 based USB-C to HDMI adapter with a macOS targeted
firmware advertises a DisplayPort type DFP with the type byte
replicated across the whole descriptor (08 08 08 08).
i915 decodes that as "PCON limited to 18 Gbps FRL" and prunes every
mode above ~750 MHz dotclock, including all the 4k@100/120 modes the
sink EDID offers, while macOS drives 4k@120 through the same adapter
just fine via DP DSC (and amdgpu's type-scoped parser would ignore
the bogus field as well).
Only parse the field for an HDMI DFP behind a DPCD 1.1+ branch
device that reports detailed cap info, matching the type-scoped
field layout of the spec and the rest of the helpers.
Fixes: ce32a6239de6 ("drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com> (v2)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Alexander Kaplan <alexander.kaplan@sms-medipool.de>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20260610193825.2933-1-alexander.kaplan@sms-medipool.de
|
|
The SpacemiT driver fixes and new work collide with each other.
|
|
write_tpt_entry() allocates a new STAG index with c4iw_get_resource() and
bumps stats.stag.cur before programming the entry. When
write_adapter_mem() fails, it returns the error without releasing the index
or reversing the statistic. No MR is inserted into rhp->mrs, so
deregistration never reclaims it, leaking the index until device teardown.
Record whether this call allocated the index and, on a failed write, return
it to tpt_table and decrement stats.stag.cur. Key the rollback on both the
write error and that flag, not the error alone: a non-reset update carries
a caller-owned STAG that this call did not allocate and must not free.
Fixes: ec3eead21718 ("RDMA/cxgb4: Remove kfifo usage")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Only in a bare metal OS environment, the _OSC control flags like Hotplug,
PME, AER, etc. reflect the physical root bridge capabilities. But in a VM
environment, these flags reflect the hypervisor policy and in most cases,
the hypervisor disables all of these control flags to the guest.
So copying these flags would needlessly disable these features in the VMD
owned Root Ports. Hence, copy the flags only when VMD is running in a bare
metal OS environment.
Signed-off-by: Nirmal Patel <nirmal.patel@linux.intel.com>
[mani: commit log and comment rewording]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://patch.msgid.link/20260713220844.561357-1-nirmal.patel@intel.com
|
|
mlx5_ib_set_cc_params() resolves the port-specific mlx5_core_dev via
mlx5_ib_get_native_port_mdev() but issued MLX5_CMD_OP_MODIFY_CONG_PARAMS
through dev->mdev. On an affiliated secondary RoCE port those pointers
refer to different devices, so a write to the secondary port's cc_params
debugfs file either altered the master port or failed with a master-side
command error, while the read path already used the resolved mdev and
returned the unchanged secondary value.
Issue the command to the resolved mdev, the same device whose capabilities
were checked when its debugfs directory was created. It is already
referenced by the get/put pair, so its lifetime is safe.
Fixes: 31578defe4eb ("RDMA/mlx5: Update mlx5_ib to use new cmd interface")
Link: https://patch.msgid.link/20260726-mlx5-ib-set-cc-params-applies-conges-v1-1-a253edafe1f3@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
get_param() reads a congestion parameter as a u32 but formats it with the
signed "%d" into an 11-byte stack buffer. A value with bit 31 set, such as
0x80000000, renders as "-2147483648\n" whose full length is 12. snprintf()
stores only 11 bytes yet returns 12, so simple_read_from_buffer() treats 12
bytes as valid and reads one byte past lbuf[].
Size the buffer for the widest unsigned decimal, format with "%u" to match
the u32, and use scnprintf() so the length passed to
simple_read_from_buffer() reflects the bytes actually stored.
Fixes: 4a2da0b8c0782 ("IB/mlx5: Add debug control parameters for congestion control")
Link: https://patch.msgid.link/20260726-get-param-leaks-kernel-stack-memory-v1-1-d61a4d39662d@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
When the device is in the fatal error state, write_tpt_entry() returns -EIO
before handing the caller's preallocated skb to the transmit path; its
allocation-failure returns do the same. c4iw_dereg_mr() ignores the error
and frees mhp, leaking mhp->dereg_skb. c4iw_get_dma_mr() instead frees the
skb a second time after dereg_mem() already consumed it, a double free.
Make write_tpt_entry() the sole owner of a non-NULL skb, freeing it on
every return preceding handoff to c4iw_ofld_send(): fatal error, tpt and
stag allocation failure. c4iw_ofld_send() consumes the skb on success and
error alike, so drop the redundant kfree_skb() in c4iw_get_dma_mr() after
dereg_mem().
Fixes: 0f8ab0b6e91b ("RDMA/iw_cxgb4: Low resource fixes for Memory registration")
Link: https://patch.msgid.link/20260726-leaked-mhp-dereg-skb-in-c4iw-dereg-m-v1-1-ebd6df364d53@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Add a dedicated .kunitconfig for running the GPU buddy allocator tests.
Signed-off-by: Krzysztof Niemiec <krzysztof.niemiec@intel.com>
Reviewed-by: Sebastian Brzezinka <sebastian.brzezinka@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Link: https://patch.msgid.link/20260729091816.27860-4-krzysztof.niemiec@intel.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
CONFIG_GPU_BUDDY is currently not selectable by the user, mirroring
how CONFIG_DRM_BUDDY does it - the idea is for a driver that makes use
of it to include a "select GPU_BUDDY" line in its kconfig.
CONFIG_DRM_BUDDY is also selected when building with
CONFIG_DRM_KUNIT_TEST, as it can be thought of as building a mock
"driver" running the tests, that makes use of the buddy functionality.
CONFIG_GPU_BUDDY_KUNIT_TEST doesn't follow that logic, requiring
GPU_BUDDY to be selected already instead of selecting it itself. This
requires building the test kernel with another driver that uses
DRM_BUDDY, as this is currently the only kconfig option that selects
GPU_BUDDY. That shouldn't be required to run unit tests for a module
now completely independent from DRM, let alone any specific driver.
Fix the dependency declaration in CONFIG_GPU_BUDDY_KUNIT_TEST to make it
work as intended, mirroring the setup in CONFIG_DRM_KUNIT_TEST.
Signed-off-by: Krzysztof Niemiec <krzysztof.niemiec@intel.com>
Reviewed-by: Sebastian Brzezinka <sebastian.brzezinka@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Krzysztof Karas <krzysztof.karas@intel.com>
Link: https://patch.msgid.link/20260729091816.27860-3-krzysztof.niemiec@intel.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
ems_usb_read_bulk_callback() walks CPC messages packed in one USB
receive buffer.
Check that each declared message fits in the URB payload. Also require the
type-specific payload to cover the fields used by the CAN, state, error and
overrun handlers.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260706092752.79600-1-pengpeng@iscas.ac.cn
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
resubmit failure
es58x_read_bulk_callback() resubmits the RX URB after processing a received
packet. If the resubmit succeeds, the URB remains anchored and will be
handled by the normal RX path or by teardown.
However, if usb_submit_urb() fails, the callback unanchors the URB and then
returns directly. This skips the existing free_urb path, so the coherent
transfer buffer allocated with usb_alloc_coherent() is not released.
Reuse the existing free_urb path after a resubmit failure so that the RX
coherent buffer is freed before leaving the callback.
Fixes: 5eaad4f76826 ("can: usb: etas_es58x: correctly anchor the urb in the read bulk callback")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/20260706014601.415445-1-lgs201920130244@gmail.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
failure
If the allocation of the SKB in gs_usb_receive_bulk_callback() fails, the
driver returns from the callback without resubmitting the URB in order to
receive further USB in URBs.
This results in a silent performance degradation which, if it occurs
repeatedly, results in starvation of USB in traffic.
Instead of returning immediately, try to resend the URB. If this also
fails, this is logged as an info message.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Fixes: 26949ac935e3 ("can: gs_usb: add CAN-FD support")
Link: https://patch.msgid.link/20260709-gs_usb-resubmit-urb-v1-1-4dd40030cc84@pengutronix.de
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
bittiming is configured
c_can_chip_config() was programming C_CAN_CTRL_REG without CONTROL_INIT,
which may allow the controller to become active before
c_can_set_bittiming() finishes.
That creates a short timing window where the peripheral can interact with
the bus using a different/default bitrate, potentially generating bus
errors and corrupting traffic.
Set CONTROL_INIT together with the control-mode writes in
c_can_chip_config() (normal, loopback and listen-only paths), so the
controller stays halted until bit timing is fully programmed.
This prevents transient bus disturbance during startup when the configured
bitrate differs from the active bus bitrate.
Signed-off-by: Lucas Martins Alves <lucas.alves@lumal21.com.br>
Link: https://patch.msgid.link/20260714164839.771123-1-lucas.alves@lumal21.com.br
Fixes: 881ff67ad450 ("can: c_can: Added support for Bosch C_CAN controller")
Cc: stable@kernel.org
[mkl: remove space before close parenthesis]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
fw_parse() reads a fixed record header, a firmware-provided payload,
and a trailing checksum without knowing the end of the firmware blob. A
truncated record can therefore make those reads exceed the blob.
The same record also supplies addresses and lengths for writes into
DPRAM. The generic loader uses wrap-prone mixed signed arithmetic for its
bounds check, while the application loader does not bound the staging
copy at all.
Pass the firmware end to the parser and validate the full source record.
Use a signed wide offset for generic DPRAM records and validate the
application staging span against the mapped DPRAM before copying.
Fixes: 03fd3cf5a179 ("can: add driver for Softing card")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260722044347.2708-1-pengpeng@iscas.ac.cn
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Testing CANFD on RZ/G3E shows that many registers do not reset to their
initial values with the current flow of deasserting resets first and then
enabling clocks.
Based on the HW manual, clocks should be supplied first and the
resets deasserted afterward.
section 7.4.3 Procedure for Activating Modules: RZ/G2L
section 4.4.9.3 Procedure for Starting up Units: RZ/G3E
So, update the order of the initializing flow for resets and clocks
to match the hardware manual, resetting all CANFD registers to their
initial values. Also update rcar_canfd_global_deinit() to assert
resets before disabling clocks, so the teardown path mirrors the new
init ordering.
Fixes: 76e9353a80e9 ("can: rcar_canfd: Add support for RZ/G2L family")
Signed-off-by: Tu Nguyen <tu.nguyen.xg@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/20260625135216.130450-1-biju.das.jz@bp.renesas.com
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
extents
The wait and bulk receive paths walk variable-length commands from a
USB buffer. A nonzero command shorter than CMD_HEADER_LEN can still be
dispatched, and the wait path copies a matching command into a fixed
caller-owned struct kvaser_cmd using the device-provided length.
Reject nonzero commands that do not contain the fixed header or that
extend beyond the current USB buffer item. In the wait path, also reject
a matching command that exceeds the destination before copying it.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260722042221.44066-1-pengpeng@iscas.ac.cn
Cc: stable@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
kvaser_usb_hydra_get_busparams()
The memory allocated for cmd is not freed after the call to
kvaser_usb_send_cmd() in both the normal and error paths.
Fix that by adding a kfree() immediately after the call.
Fixes: 39d3df6b0ea8 ("can: kvaser_usb: Compare requested bittiming parameters with actual parameters in do_set_{,data}_bittiming")
Cc: stable@vger.kernel.org
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Link: https://patch.msgid.link/20260722103906.108571-1-nihaal@cse.iitm.ac.in
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
pcan_usb_fd_decode_buf() walks uCAN records packed in one USB
receive buffer.
Require each record to contain the fixed header for its type, and verify
CAN payload bytes before copying them into the skb.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260706092836.79754-1-pengpeng@iscas.ac.cn
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
