| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
reg_defaults must be sorted by ascending register address, as
regcache_lookup_reg() locates entries in it with bsearch(). See commit
fd80df352ba1 ("regcache: Add support for sorting defaults arrays").
cs35l45_defaults[] lists the DSP1_RX*_RATE and DSP1_TX*_RATE registers
(0x02b80080 - 0x02b802b8) in the middle of the table, ahead of entries with
much lower addresses, so the binary search does not find 36 of its 73
entries. regcache_reg_needs_sync() then cannot compare those against their
default and reports that a sync is needed, so they are written to the
device on every regcache_sync() even when they were never touched.
Sort the table by register address.
Fixes: 74b14e2850a3 ("ASoC: cs35l45: DSP Support")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260805082413.26174-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
reg_defaults must be sorted by ascending register address, as
regcache_lookup_reg() locates entries in it with bsearch(). See commit
fd80df352ba1 ("regcache: Add support for sorting defaults arrays").
cs35l41_reg[] lists CS35L41_BSTCVRT_PEAK_CUR (0x3808) after
CS35L41_BSTCVRT_COEFF (0x3810) and CS35L41_BSTCVRT_SLOPE_LBST (0x3814), so
the binary search does not find those two entries.
regcache_reg_needs_sync() then cannot compare them against their default
and reports that a sync is needed, so they are written to the device on
every regcache_sync() even when they were never touched.
Sort the table by register address.
Fixes: 5f2f539901b0 ("ASoC: cs35l41: Correct handling of some registers in the cache")
Cc: stable@vger.kernel.org
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260805082413.26174-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CCW build path (prefix_LRE, the full-track prefix and dso_ras) read the
base address and LSS straight from conf.ned. That buffer is freed and
reallocated by the reload worker (do_reload_device - dasd_eckd_read_conf -
dasd_eckd_clear_conf_data), so a configuration change concurrent with I/O
can free conf.ned while a request is being built.
Use-after-free reported by KASAN in prefix_LRE.
Read the cached copies instead.
The unit address is already kept in uid.real_unit_addr, and the LSS is now
cached in ned_lss. Both are refreshed under the ccwdev lock in
dasd_eckd_generate_uid whenever the configuration is (re)read.
Also fix for prepare for read subsystem data (prssd) users.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-20-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Re-enable block-layer discard for ESE ECKD volumes, releasing thin space
via release allocated space (RAS).
This is based on
commit 7e64db1597fe ("s390/dasd: Add discard support for ESE volumes")
but adapted to the current code and fixed.
REQ_OP_DISCARD is routed to a RAS release over the request's track range,
and discard requests run on the base device only. Discard limits use extent
granularity via the disc_limits discipline hook so the block layer only
issues extent-aligned discards.
Discard is gated on the DASD_FEATURE_DISCARD device feature rather than a
per-discipline flag: the driver sets the feature when the volume is on ESE
hardware (i.e. RAS is available), and the block-layer setup enables discard
limits for a device that has it.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-19-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Extend the device information line logged when a volume comes online with
the ESE hardware capability and the on-disk format mode. The format mode
(full or on demand) is derived from the on-disk format label alone, so a
volume that is not backed by ESE hardware but was still formatted on
demand is reported correctly.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-18-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Read the format label from track 0 record 4 at device bring-up and cache
it. When a valid label is present, is_ese() is derived from it instead of
the hardware volume field.
A volume copied off ESE storage onto other hardware is thus still handled
as thin.
Without a label (older format) is_ese() falls back to the hardware field as
before.
The cache is refreshed after a format so is_ese() stays coherent without an
offline/online cycle.
The label F_ESE bit is stamped from the hardware capability rather than
is_ese(), and space release (quick format) is gated on the hardware
capability, so a copied label cannot enable it on non-ESE hardware.
The ese sysfs attribute, and with this lsdasd, shows the hardware
capability and not the internal handling. This is in line with the view
from storage server interface. To reflect the specific internal handling an
additional attribute on_demand_formatting is added to show that a device is
handled like an ESE device internally based on the disk label.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-17-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When a CDL volume is formatted, write a small on-disk label so the format
can later be recognised by the kernel. The next patch will use this for
ESE detection.
The label records a magic, a version, whether the volume is ESE, and
whether it was formatted quick (space released, thin) or full.
It lives in track 0, head 0, record 4 (the first non-special CDL record).
R4 is written by the same channel program that formats track 0
- its WRITE_CKD transfers count + the label data instead of count-only -
so label and track format reach the disk atomically; a valid magic then
marks a completed format without a separate, racy write.
Quick vs full is derived from a full space release (RAS) preceding the
format: dasd_eckd_release_space_full() sets a per-device flag the next
format consumes. Non-ESE volumes and formats without a preceding full
release are recorded as full.
struct dasd_format_label is exactly 512 bytes (the smallest block size)
so it fits one record; larger blocks zero-pad the rest.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-16-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When executing the command `make cscope`, the `cscope.files` file
generated by it includes only filenames with the extensions *.h, *.c,
*.S and not includes filenames with *.rs extensions.
To fix this, modify the functions `find_arch_sources()`,
`find_arch_include_sources()`, `find_include_sources()`, and
`find_other_sources()` so that they can accept an unlimited number of
filename patterns as parameters for the search. Add the
`setup_name_pattern()` function to convert these filename pattern
parameters into a list of parameters that can be passed to the `find`
utility via the new `pattern` variable.
Signed-off-by: Sergei Litvin <litvindev@gmail.com>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Nicolas Schier <n.schier@fritz.com>
Reviewed-by: Nicolas Schier <n.schier@fritz.com>
Link: https://patch.msgid.link/20260714125259.78824-1-litvindev@gmail.com
[nsc: cleaned-up commit message line breaks and removed cc trailers]
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
When executing the command `make COMPILED_SOURCE=1 cscope`, the resulting
`cscope.files` file contains filenames with the extensions *.rlib, *.rmeta,
and *.so.
To fix this, modify the regular expression in the `all_compiled_sources()`
function so that only files with the extensions *.h, *.c, *.S, and *.rs are
accepted.
The issue has been introduced by commit 4f491bb6ea2a ("scripts/tags.sh:
collect compiled source precisely") which implemented the parsing of
compiled sources from *.cmd files instead of using the "find" command.
Fixes: 4f491bb6ea2a ("scripts/tags.sh: collect compiled source precisely")
Signed-off-by: Sergei Litvin <litvindev@gmail.com>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Nicolas Schier <n.schier@fritz.com>
Reviewed-by: Nicolas Schier <n.schier@fritz.com>
Link: https://patch.msgid.link/20260714083331.69482-1-litvindev@gmail.com
[nsc: cleaned-up commit message line breaks and removed cc trailers]
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
Turn the middle of the ft_bias range (1..99) into an adaptive heuristic
that switches between fulltrack write (ft1) and plain write ft0 depending
on how sparse the device still is.
A sparse device benefits from fulltrack writes (it avoids the format/retry
cycle); once enough tracks are formatted the per-write overhead of
ft1 outweighs that. An state machine measures the NRF rate in short ft0
probe windows and flips back to ft1 when it is high
(FT1_ACTIVE -> PROBING -> FT0_STABLE, with a backing-off reprobe interval).
The four parameters are derived from ft_bias by linear interpolation,
anchored so ft_bias == 50 derives the following values:
ese_heu_start_interval - 2000 - IOs in ft1, before first ft0-Probe starts
ese_heu_probe_window - 100 - IOs in probe window
ese_heu_nrf_high - 10 ‰ (= 1 %) - TRACK_FORMAT rate that leads to ft1
ese_heu_max_interval - 500000 - Backoff-Cap: max. IOs between two probes
Higher is more eager to use ft1, and 0/100 skips the heuristic.
The NRF counter is bumped in dasd_eckd_ese_format() for both the classic
NRF sense and the HPF INV_TRACK_FORMAT equivalent.
The state machine resets to ft1 on check_characteristics, full format,
and release-space.
A read-only ese_heuristic_state sysfs attribute exposes the current mode.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-15-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a single per-device 'full_track_bias' sysfs attribute (0..100) that
gates the full-track write path. 0 disables it, 100 routes every aligned,
full-track write through dasd_eckd_build_cp_tpm_writefulltrack(). Values in
between are reserved for the adaptive heuristic added in the next patch.
For now any non-zero value simply enables full-track writes. Internally the
value is kept in the per-device 'ft_bias' field.
This will control the default IO path only.
In case we get an unformatted track error it will always be used to format
and write the track in one go.
The WRITE_FULL_TRACK command has an advantage on sparse formatted ESE
devices but it has an overall penalty for maximum throughput compared to
usual track based IO.
The attribute lives at /sys/bus/ccw/devices/<devid>/full_track_bias and
accepts 0..100. The default is DASD_FT_BIAS_DEFAULT; together with the
adaptive heuristic added in the next patch it uses full-track writes only
where they pay off, avoiding the ESE format penalty out of the box while
keeping the throughput cost off already-formatted volumes.
A 'full_track_bias' module parameter sets the initial value applied to
every device at online time; individual volumes can still be re-tuned
through their sysfs attribute afterwards.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-14-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Wire dasd_eckd_build_cp_tpm_writefulltrack() into the ESE unformated
track handler.
dasd_eckd_ese_format() now returns void (matching the revised discipline
hook): it computes the failing track/record range, trims a partially
covered last track when several tracks are involved (the block layer
re-issues the remainder), claims the range with
test_and_set_format_track(), builds a writefulltrack CQR, copies
callback_data/proc_bytes from the origin, and stages it on
block->ese_staging. The origin CQR is set to DASD_CQR_ABORT so
__dasd_process_cqr() retires it without the normal completion.
Drop dasd_eckd_ese_format_cb(); the format-entry slot is now released by
dasd_eckd_free_alias_cp() via clear_format_track() when the CQR is freed.
dasd_int_handler() calls the void hook directly and, for writefulltrack
CQRs (cqr->filldata set), returns DASD_CQR_ERROR instead of looping on
the NRF.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-13-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add the channel program builder for WRITE_FULL_TRACK requests, used
by dasd_eckd_ese_format() (next patch) to format and write a set of
tracks atomically and avoid the format cycle on ESE devices.
The program is an ITCW with a TIDAW list. Per track it emits an eckd_r0
header, an eckd_count + data pair for every record (pad records before
and after the caller's data window use device->nulldata, records in the
window point into the bio payload), and a terminating 0xFF pseudo-count
with TIDAW_FLAGS_INSERT_CBC. The descriptors come from the per-device
fill_chunks pool so they can be freed in bulk in __dasd_cleanup_cqr().
Add inline helpers crosses_page() and reserve_nocross(), to keep each
descriptor within one page since TIDAW addressing must not cross a page
boundary.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-12-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
prepare_itcw() builds the FCX prefix block (PFX + LRE) for track-mode
I/O. Extend it to handle DASD_ECKD_CCW_WRITE_FULL_TRACK.
WRITE_FULL_TRACK needs two extra bytes appended to the LRE for that
bitmask. The prefix block is a scratch buffer copied into the TCCB by
itcw_add_dcw(), so keep it on the stack (sized for the two extra bytes)
rather than allocating it: this runs in the writeback path and must not
depend on an allocation that can fail under memory pressure.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-11-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Replace the single per-device format_entry slot with an array of 16
slots so multiple format requests can be in flight at once, and extend
struct dasd_format_entry with a start_trk/end_trk/cqr range (replacing
the single track field).
Rewrite test_and_set_format_track() to scan the array for range overlaps
instead of a trkcount snapshot, honour the early-collision flag, and
return the allocated slot to the caller.
Add dasd_req_conflict() and extend dasd_return_cqr_cb() to mark in-flight
data CQRs that overlap a just-completed format range, so the next
test_and_set_format_track() detects the conflict early.
Remove the now-obsolete trkcount snapshot in dasd_start_IO().
The detection added here only becomes active together with the
WRITE_FULL_TRACK ESE format handler later in the series: that patch routes
the format request through dasd_return_cqr_cb() (so completion runs the
overlap hook with cqr->format set) and records each request's
start_trk/end_trk range. Until then the array and the conflict check are in
place but dormant.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-10-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add the driver internals to build WRITE_FULL_TRACK FCX channel programs
in response to unformatted tracks on ESE devices.
struct dasd_ccw_req: filldata, a pointer to the per-track metadata (an R0
record and the count records) that the WRITE_FULL_TRACK TIDAWs point at,
and format/start_trk/end_trk/collision that link a request to its
format-track guard entry so an overlapping format request can be detected.
struct dasd_device: fill_mem/fill_chunks pool for those buffers and a
zeroed nulldata page used as the data source for pad records.
struct dasd_block: ese_staging/ese_lock, a hardirq-safe staging list. An
ESE format CQR is created in the interrupt handler but has to be enqueued
on ccw_queue under queue_lock; taking queue_lock while the ccwdev_lock is
held there would invert the lock order, so the CQR is staged under ese_lock
and dasd_block_tasklet splices it onto ccw_queue. Existing locking is
unchanged.
Add CQR states DASD_CQR_ABORT/ABORTED to retire the origin CQR of a
replaced write without completing it to the block layer, and struct
eckd_r0 for the track header record.
The CCW and ESE format pools are enlarged (a full-track ITCW is roughly
twice a plain track-mode one) to keep two maximum-size requests in flight.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-9-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The track address of an Extended Address Volume (more than 65520
cylinders) carries the high cylinder bits that do not fit the 16-bit cyl
field in the upper part of the head field. set_ch_t() open-codes the
corresponding shifts; name them so the encoding is explicit and can be
reused.
No functional change.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-8-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
dasd_alloc_device() runs in process context (device set_online), so its
pool allocations do not need GFP_ATOMIC. Use GFP_KERNEL instead, which is
more reliable, especially for the larger DMA allocations that later ESE
full-track work adds here.
No functional change intended.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-7-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
With 4096-byte blocks a full ECKD track holds exactly 12 records. Lower
DASD_ECKD_MAX_BLOCKS from 190 to 180 so requests align to track
boundaries (15 full tracks); full-track I/O is more efficient than
partial-track writes, and 190 had no alignment significance and could
let a request cross a track boundary.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-6-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
__dasd_cleanup_cqr() maps the completion result to a block status by
reading cqr->intrc, but only after discipline->free_cp() has returned the
request block to its memory pool (dasd_eckd_free_cp() ends in
dasd_sfree_request()). On SMP another CPU can reallocate that block and
overwrite cqr->intrc before it is read, completing the request with the
wrong error. proc_bytes is already snapshotted before free_cp() for the
same reason; do the same for intrc.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-5-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Several sysfs show/store handlers call a discipline callback that
dereferences device->private, either directly or through the
DASD_DEFINE_ATTR() macro. During dasd_generic_set_online() the discipline
is assigned before check_device() allocates device->private, so an
unprivileged read of one of these world-readable attributes in that window
dereferences a NULL pointer and panics.
Guard the dereference inside each callback that actually touches
device->private.
Fixes: c729696bcf8b ("s390/dasd: Recognise data for ESE volumes")
Cc: stable@vger.kernel.org
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
dasd_default_erp_postaction() copies the timing and device state from
the finished ERP request back to the original request but drops
proc_bytes. A request that was partially completed, an ESE read of a
not-yet-allocated track returns fewer bytes than requested, and then
recovered through the ERP chain loses its partial-completion length.
__dasd_cleanup_cqr() then sees proc_bytes == 0 and completes the whole
request instead of requeueing the remainder, silently returning zeroed
data for the part that was never read.
Carry proc_bytes over to the original request like the other
per-request state.
Fixes: 5e6bdd37c552 ("s390/dasd: fix data corruption for thin provisioned devices")
Cc: stable@vger.kernel.org
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
dasd_int_handler() completes an NRF read of an unallocated ESE track by
calling ese_read() and unconditionally marking the request
DASD_CQR_SUCCESS. dasd_eckd_ese_read() can return an error before it has
zeroed the destination buffer: a failed sense-data parse or a current
track outside the requested range both return early, leaving the
destination pages untouched. The request is still completed successfully,
so the block layer is handed stale / uninitialized memory instead of
zeros.
Check the ese_read() return value and fail the request through the normal
error path instead of forcing DASD_CQR_SUCCESS.
Fixes: 5e6bdd37c552 ("s390/dasd: fix data corruption for thin provisioned devices")
Cc: stable@vger.kernel.org
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260805111612.1285190-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add myself as Kconfig reviewer, as privately discussed with the Kconfig
maintainers.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20260804141436.1451211-1-julianbraha@gmail.com
Signed-off-by: Nicolas Schier <nsc@kernel.org>
|
|
Commit c0f691388992 ("intel_idle: Use subsys_initcall_sync() for
initialization") effectively made intel_idle initialize earlier which
turns out to interfere with USB EHCI probing on some platforms [1].
Investigation led to the conclusion that this was related to allowing
package idle states to be used earlier than before.
Work around that issue by making intel_idle set a CPU latency QoS
request to prevent package idle states from being used on all platforms
supported by it for the duration of the device_initcall() initialization
phase.
Fixes: c0f691388992 ("intel_idle: Use subsys_initcall_sync() for initialization")
Reported-by: Julian Silver <mendaxca@gmail.com>
Tested-by: Julian Silver <mendaxca@gmail.com>
Closes: https://lore.kernel.org/linux-acpi/3353bdf3-4f33-44b1-809b-b0378bee5816@gmail.com/
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://patch.msgid.link/5120454.31r3eYUQgx@rafael.j.wysocki
|
|
It turns out that commit 5fce67641a3e ("x86/mm/pat: Don't gate
cpa_lock on debug_pagealloc_enabled()") was a little too quick to
remove the debug_pagealloc exception for cpa_lock.
Notably __kernel_map_pages() is used by the page-allocator from any
context the page-allocator itself is used, which violates the cpa_lock
rules.
Re-instate the exception, except make it specific to the
__kernel_map_pages() such that any other cpa() usage is still fully
serialized by cpa_lock. Also note that since cpa() should not be used
on memory that isn't allocated, the page-allocator locking and cpa are
infact mutually exclusive and all cpa usage in fully serialized.
Add a comment explaining this and other 'funnies' surrounding
DEBUG_PAGEALLOC, including how pgd_lock is not affected and the TLB
trickery.
Fixes: 5fce67641a3e ("x86/mm/pat: Don't gate cpa_lock on debug_pagealloc_enabled()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20260729111119.604452135@infradead.org
|
|
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20260729111119.488154104@infradead.org
|
|
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20260729111119.375614011@infradead.org
|
|
Correct the address of the HALO_SCRATCH4 entry in halo_register_defaults[].
This doesn't affect the validity of the KUnit testing because none of the
tests rely on this value. It's only defaulted because cs_dsp will read it
when the DSP state changes from running to stopped - this would only have
logged a warning about failure to read the register but it doesn't cause
anything to fail.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260805105223.956785-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The handling of extra memory regions done in balloon_add_regions() is not
correct for PV guests, since the initial target is set to reflect the real
memory the system has, not what's described on the memory map, which can be
higher if memory != maxmem.
Introduce separate logic for addition vs subtraction in
balloon_add_regions() and handle extra regions correctly by adding them to
the total amount of pages, instead of subtracting from the current and
target pages amounts.
In the common case PV domU/dom0 and PVH dom0 will use the addition path,
since the initial target reflects the real assigned memory. HVM and PVH
domUs use the subtraction path, since the target is set based on the amount
of memory reported in the memory map, without accounting for released
regions.
Fixes: 87af633689ce ("x86/xen: fix balloon target initialization for PVH dom0")
Fixes: 0949c646d646 ("Partial revert "x86/xen: fix balloon target initialization for PVH dom0"")
Signed-off-by: Roger Pau Monné <roger@xenproject.org>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Tested-by: Matthias Goergens <matthias.goergens@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260805094008.95778-1-roger@xenproject.org>
|
|
When device just got initialized (for example on module load), the
otherend_id field is initialized only after
xenbus_read_otherend_details() gets called. If xenstore watch triggers
xenbus_dev_changed() before that, it might consider still zeroed
otherend_id field (not matching actual xenstore content) as a sign of
device state reset. It can happen because xenstore watch are handled in
another thread (xenwatch), which can run in parallel to the initial
device probe running at module load. In that case, it would call
device_unregister(), which would deadlock against device probe from
module init.
Fix this by considering dev->otherend_id change only after dev->otherend
is set (which happen after otherend_id is initialized).
Fixes: e2dcf9065536 "xen/xenbus: better handle backend crash"
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260803030822.4104093-2-marmarek@invisiblethingslab.com>
|
|
Ease diagnosing what actually changed.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260803030822.4104093-1-marmarek@invisiblethingslab.com>
|
|
The current code creates one hwmon device per thermal zone type and that
device is registered under the first thermal zone of the given type.
That turns out to be problematic when the thermal zone holding the
hwmon device is removed.
For example, say that there are two ACPI thermal zones on a system
/sys/devices/virtual/thermal/thermal_zone0/
/sys/devices/virtual/thermal/thermal_zone1/
The current code registers a hwmon class device for thermal_zone0 only:
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/
because the type is "acpitz" for both of them, but it adds a sysfs
attribute that belongs to thermal_zone1 under it:
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp2_input
There is also
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp1_input
which belongs to thermal_zone0.
When thermal_zone0 is removed, say because the ACPI thermal driver is
unbound from the underlying platform device, thermal_remove_hwmon_sysfs()
skips the removal of hwmon0 because of the temp2_input attribute
belonging to thermal_zone1 which effectively prevents thermal_zone0
removal from making progress.
Address this by making thermal_remove_hwmon_sysfs() remove the entire
hwmon class device interface for the given thermal zone type when the
thermal zone device holding it is removed.
To prevent races with thermal_add_hwmon_sysfs() that may interfere
with this, carry out the entire addition and removal of hwmon sysfs
interfaces for thermal zones under thermal_hwmon_list_lock.
Also adjust the layout of the labels in thermal_add_hwmon_sysfs() to
the current kernel coding style to align with the new "unlock" label.
Link: https://lore.kernel.org/linux-pm/20260402021828.16556-1-liujia6264@gmail.com/
Fixes: f6b6b52ef7a5 ("thermal_hwmon: Pass the originating device down to hwmon_device_register_with_info")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/5094738.GXAFRqVoOG@rafael.j.wysocki
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Pull cpupower utility updates for 7.3-rc1 from Shuah Khan:
"Adds support for generic CPPC display that depends only on standardized
fields, improving AMD specific implementation for the same.
Removes conditional return with no effect as part of tree-wide code clean
up effort."
* tag 'linux-cpupower-7.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower: remove conditional return with no effect
cpupower: Add libm to cpupower for generic CPPC view
cpupower: Print kernel and hardware frequency information
cpupower: Build and call CPPC information on non-AMD processors
cpupower: Add generic CPPC performance display
|
|
Add a DMI quirk for the MSI Raider A18 HX A7VHG fixing the
issue where the internal microphone was not detected.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221574
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260805091600.318018-2-zhangheng@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a DMI quirk for the Xiaomi RedmiBook 16 2025 (AMD) fixing the
issue where the internal microphone was not detected.
Link: https://github.com/thesofproject/linux/issues/5860
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260805091600.318018-1-zhangheng@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both target Intel's skylake-driver, previously found in sound/soc/intel
which has been removed few years ago and succeeded by the avs-driver.
snd_sst_tokens.h is succeeded by uapi/sound/intel/avs/tokens.h
skl-tplg-interface.h to the best of my knowledge has no users. Its types
are reflected in sound/soc/intel/avs/messages.h and are not intended for
public use. Closest public equivalent would be the firmware's
processing modules but in such case a user has to compile against
Intel's AudioDSP headers, not Linux ones.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20260805064435.429654-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Revert commit 030a48b0f6ce ("thermal/drivers/hwmon: Cleanup coding style
a bit") that introduced a use-after-free into the error path of
thermal_add_hwmon_sysfs() by removing a valid check from it.
Link: https://lore.kernel.org/linux-hwmon/20260803183915.4ED7D1F000E9@smtp.kernel.org/
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/5123895.31r3eYUQgx@rafael.j.wysocki
|
|
Currently `pin-init` crate is missing many inline annotations. They are all
generic so still get inlined in normal builds, but are not inlined in
`-C opt-level=s` build. Mark these functions as `#[inline]` so they are
considered for inlining regardless.
Signed-off-by: Gary Guo <gary@garyguo.net>
|
|
Remove `__pinned_init` for kernel configuration, with all users gone.
Still perserve it temporarily as deprecated so other users have time to
move off it.
Link: https://patch.msgid.link/20260729-merge-init-v2-5-26adf47109e7@garyguo.net
Signed-off-by: Gary Guo <gary@garyguo.net>
|
|
The `__init` method is not designed to be a public API (existence of "__"
is a hint for this); replace users with `pin_init::raw_[try_]init` which
does the same thing.
There are a few users of `__init` which are replaced as well.
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patch.msgid.link/20260729-merge-init-v2-4-26adf47109e7@garyguo.net
Signed-off-by: Gary Guo <gary@garyguo.net>
|
|
The `__init` method is not designed to be a public API (existence of "__"
is a hint for this); but currently there is no other API that allows raw
initialization on pointers. Add `raw_init` and `raw_try_init` and recommend
people to use this instead if raw pointer initialization is needed.
Link: https://patch.msgid.link/20260729-merge-init-v2-3-26adf47109e7@garyguo.net
[ Renamed from `ptr_[try_]init` to `raw_[try_]init`. - Gary ]
Reviewed-by: Benno Lossin <lossin@kernel.org>
Signed-off-by: Gary Guo <gary@garyguo.net>
|
|
Add a verifier test that a load-acquire fetching into its own source
register (dst_reg == src_reg) from a ctx pointer is rejected.
# LDLIBS=-static PKG_CONFIG='pkg-config --static' ./vmtest.sh -- ./test_progs -t verifier_load_acquire
[...]
#614/1 verifier_load_acquire/load-acquire, 8-bit:OK
#614/2 verifier_load_acquire/load-acquire, 8-bit @unpriv:OK
#614/3 verifier_load_acquire/load-acquire, 16-bit:OK
#614/4 verifier_load_acquire/load-acquire, 16-bit @unpriv:OK
#614/5 verifier_load_acquire/load-acquire, 32-bit:OK
#614/6 verifier_load_acquire/load-acquire, 32-bit @unpriv:OK
#614/7 verifier_load_acquire/load-acquire, 64-bit:OK
#614/8 verifier_load_acquire/load-acquire, 64-bit @unpriv:OK
#614/9 verifier_load_acquire/load-acquire with uninitialized src_reg:OK
#614/10 verifier_load_acquire/load-acquire with uninitialized src_reg @unpriv:OK
#614/11 verifier_load_acquire/load-acquire with non-pointer src_reg:OK
#614/12 verifier_load_acquire/load-acquire with non-pointer src_reg @unpriv:OK
#614/13 verifier_load_acquire/misaligned load-acquire:OK
#614/14 verifier_load_acquire/misaligned load-acquire @unpriv:OK
#614/15 verifier_load_acquire/load-acquire from ctx pointer:OK
#614/16 verifier_load_acquire/load-acquire from ctx pointer @unpriv:OK
#614/17 verifier_load_acquire/load-acquire from ctx pointer, same dst and src register:OK
#614/18 verifier_load_acquire/load-acquire from ctx pointer, same dst and src register @unpriv:OK
#614/19 verifier_load_acquire/load-acquire with invalid register R15:OK
#614/20 verifier_load_acquire/load-acquire with invalid register R15 @unpriv:OK
#614/21 verifier_load_acquire/load-acquire from pkt pointer:OK
#614/22 verifier_load_acquire/load-acquire from flow_keys pointer:OK
#614/23 verifier_load_acquire/load-acquire from sock pointer:OK
#614 verifier_load_acquire:OK
Summary: 1/23 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20260804201917.253491-2-daniel@iogearbox.net
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
|
|
check_atomic_load() calls check_load_mem() before atomic_ptr_type_ok().
For a load-acquire that fetches into its own source register (dst_reg ==
src_reg), check_load_mem() overwrites src_reg's type with the type of the
loaded value, so the subsequent atomic_ptr_type_ok() no longer sees the
source pointer and fails to reject the disallowed types (ctx, pkt,
flow_keys, sock).
Since bpf_convert_ctx_accesses() does not rewrite atomic loads, the raw
access to the underlying kernel object is left in place. The destination
type is taken from the ctx access itself, so a load-acquire of the sk
field of struct __sk_buff for example leaves the register typed as
PTR_TO_SOCK_COMMON_OR_NULL, which type_is_sk_pointer() does not match
either, while it actually holds unconverted struct sk_buff bytes. Once
the NULL check has passed this is a type confusion, not just a leak of
kernel data.
Validate src_reg with check_reg_arg() and check the source pointer type
with atomic_ptr_type_ok() before the load again, mirroring
check_atomic_rmw(). Out-of-range register numbers are already rejected
earlier by check_and_resolve_insns() (commit 503d21ef8eac ("bpf: Do
register range validation early")), and the only exemption there,
is_stack_arg_ldx(), requires BPF_LDX | BPF_MEM | BPF_DW and thus never
matches a BPF_ATOMIC insn. atomic_ptr_type_ok() can therefore not
dereference register state out of bounds, that is, the out-of-bounds
read addressed by the Fixes commit below does not reappear (as proven
also via selftest).
Fixes: c03bb2fa327e ("bpf: Fix out-of-bounds read in check_atomic_load/store()")
Reported-by: STAR Labs SG <info@starlabs.sg>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20260804201917.253491-1-daniel@iogearbox.net
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
|
|
When a mark gets a new event bit, fanotify and inotify may avoid
recalculating the object mask if the cached aggregate already contains that
bit. This is racy with a recalculation triggered by a concurrent update to
another mark on the same connector.
The concurrent scan can read the mark before the new bit is added, while
the updater reads the old aggregate before that scan publishes its result.
The updater then skips recalculation and the scan publishes a mask without
the bit, leaving the object mask stale after both updates complete.
This can be reproduced with two fanotify groups watching the same inode:
one thread removes FAN_MODIFY from one existing mark while another thread
adds FAN_MODIFY to the other mark. After both fanotify_mark() calls return,
writes can fail to produce FAN_MODIFY for the group whose mark now contains
the bit. This was reproduced on an unmodified v6.12.95 kernel. The
equivalent inotify interleaving loses IN_MODIFY events.
For normal fanotify additions, recalculate whenever the raw mark mask
changes. The normal mask is not cleared asynchronously, so an unchanged
addition cannot introduce missing interest. Always recalculate ignore-mask
updates because FS_MODIFY handling may clear the ignore mask without taking
mark->lock, making snapshot comparisons unreliable.
Always recalculate after updating an existing inotify watch. Its replace
path temporarily sets mark->mask to zero, so a concurrent scan can observe
zero even when the old and final masks are equal. Assigning the replacement
mask directly would avoid the transient zero, but existing-watch updates
are infrequent, so unconditional recalculation is simpler.
Link: https://lore.kernel.org/all/CACwKKmCZdiZDoFuYm6LZhQ=XvHPk0fNKH=X3LmoXMqakYqJaNw@mail.gmail.com/
Fixes: 63c882a05416 ("inotify: reimplement inotify using fsnotify")
Fixes: 912ee3946c5e ("fanotify: do not call fanotify_update_object_mask in fanotify_add_mark")
Cc: stable@vger.kernel.org # needs adjustments for <= 7.0
Suggested-by: Jan Kara <jack@suse.cz>
Suggested-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Youngjae Kwon <yjkwon0026@snu.ac.kr>
Link: https://patch.msgid.link/20260802015801.2426818-1-yjkwon0026@snu.ac.kr
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
When checking whether to skip certain buffers because they're protected
by dmem.low, we're checking the effective protection of the evictee's
cgroup, but depending on how the evictor's cgroup relates to the
evictee's, the semantics of effective protection values change.
When testing against cgroups from different subtrees, page_counter's
recursive protection propagates memory protection afforded to a parent
down to the child cgroups, even if the children were not explicitly
protected. This prevents cgroups whose parents were afforded no
protection from stealing memory from cgroups whose parents were afforded
more protection, without users having to explicitly propagate this
protection.
However, if we always calculate protection from the root cgroup, this
breaks prioritization of sibling cgroups: If one cgroup was explicitly
protected and its siblings were not, the protected cgroup should get
higher priority, i.e. the protected cgroup should be able to steal from
unprotected siblings. This only works if we restrict the protection
calculation to the subtree shared by evictor and evictee.
Reviewed-by: Maarten Lankhorst <dev@lankhorst.se>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Link: https://patch.msgid.link/20260804-dmemcg-aggressive-protect-v8-6-07af96681bf8@gmx.de
|
|
When the cgroup's memory usage is below the low/min limit and allocation
fails, try evicting some unprotected buffers to make space. Otherwise,
application buffers may be forced to go into GTT even though usage is
below the corresponding low/min limit, if other applications filled VRAM
with their allocations first.
Reviewed-by: Maarten Lankhorst <dev@lankhorst.se>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Link: https://patch.msgid.link/20260804-dmemcg-aggressive-protect-v8-5-07af96681bf8@gmx.de
|
|
Coupling resource allocation and cgroup charging is racy when charging
succeeds, but subsequent resource allocation fails. Certain eviction
decisions are made on the basis of whether the allocating cgroup is
protected, i.e. within its min/low limits, but with the charge being
tied to resource allocation (and uncharged when the resource allocation
fails), this check is done at a point where the allocation is not actually
charged to the cgroup.
This is subtly wrong if the allocation were to cause the cgroup to exceed
the min/low protection, but it's even more wrong if the same cgroup tries
allocating multiple buffers concurrently: In this case, the min/low
protection may pass for all allocation attempts when the real min/low
protection covers only some, or potentially none of the allocated
buffers.
Instead, charge the allocation to the cgroup once and keep the charge
for as long as we try to allocate a ttm_resource, and only undo the charge
if allocating the resource is ultimately unsuccessful and we move on to
a different ttm_place.
Reviewed-by: Maarten Lankhorst <dev@lankhorst.se>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Link: https://patch.msgid.link/20260804-dmemcg-aggressive-protect-v8-4-07af96681bf8@gmx.de
|
|
Move all code for attempting allocation for a specific place to
ttm_bo_alloc_place. With subsequent patches, this logic is going to get
more complicated, so it helps readability to have this separate.
ttm_bo_alloc_at_place takes a pointer to a struct ttm_bo_alloc_state.
This struct holds various state produced by the allocation (e.g. cgroup
resource associated with the allocation) that the caller needs to keep
track of (and potentially dispose of). This is just the limiting cgroup
pool for now, but future patches will add more state needing to be tracked.
ttm_bo_alloc_at_place also communicates via return codes if eviction
using ttm_bo_evict_alloc should be attempted. This is preparation for
attempting eviction in more cases than just force_space being set.
No functional change intended.
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Maarten Lankhorst <dev@lankhorst.se>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Link: https://patch.msgid.link/20260804-dmemcg-aggressive-protect-v8-3-07af96681bf8@gmx.de
|
|
This helps to find a common subtree of two resources, which is important
when determining whether it's helpful to evict one resource in favor of
another.
To facilitate this, add a common helper to find the ancestor of two
cgroups using each cgroup's ancestor array.
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Reviewed-by: Maarten Lankhorst <dev@lankhorst.se>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Link: https://patch.msgid.link/20260804-dmemcg-aggressive-protect-v8-2-07af96681bf8@gmx.de
|
