| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Timestamping configuration through ethtool has inconsistent behavior of
skipping the reply for set command if configuration was not changed. Fix
it be providing reply in any case.
Fixes: 6e9e2eed4f39d ("net: ethtool: Add support for tsconfig command to get/set hwtstamp config")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250922231924.2769571-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, after the bridge is created, the FDB does not hold an FDB entry
for the bridge MAC on VLAN 0:
# ip link add name br up type bridge
# ip -br link show dev br
br UNKNOWN 92:19:8c:4e:01:ed <BROADCAST,MULTICAST,UP,LOWER_UP>
# bridge fdb show | grep 92:19:8c:4e:01:ed
92:19:8c:4e:01:ed dev br vlan 1 master br permanent
Later when the bridge MAC is changed, or in fact when the address is given
during netdevice creation, the entry appears:
# ip link add name br up address 00:11:22:33:44:55 type bridge
# bridge fdb show | grep 00:11:22:33:44:55
00:11:22:33:44:55 dev br vlan 1 master br permanent
00:11:22:33:44:55 dev br master br permanent
However when the bridge address is set by the user to the current bridge
address before the first port is enslaved, none of the address handlers
gets invoked, because the address is not actually changed. The address is
however marked as NET_ADDR_SET. Then when a port is enslaved, the address
is not changed, because it is NET_ADDR_SET. Thus the VLAN 0 entry is not
added, and it has not been added previously either:
# ip link add name br up type bridge
# ip -br link show dev br
br UNKNOWN 7e:f0:a8:1a:be:c2 <BROADCAST,MULTICAST,UP,LOWER_UP>
# ip link set dev br addr 7e:f0:a8:1a:be:c2
# ip link add name v up type veth
# ip link set dev v master br
# ip -br link show dev br
br UNKNOWN 7e:f0:a8:1a:be:c2 <BROADCAST,MULTICAST,UP,LOWER_UP>
# bridge fdb | grep 7e:f0:a8:1a:be:c2
7e:f0:a8:1a:be:c2 dev br vlan 1 master br permanent
Then when the bridge MAC is used as DMAC, and br_handle_frame_finish()
looks up an FDB entry with VLAN=0, it doesn't find any, and floods the
traffic instead of passing it up.
Fix this by simply adding the VLAN 0 FDB entry for the bridge itself always
on netdevice creation. This also makes the behavior consistent with how
ports are treated: ports always have an FDB entry for each member VLAN as
well as VLAN 0.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/415202b2d1b9b0899479a502bbe2ba188678f192.1758550408.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The kernel forbids the creation of non-FDB nexthop groups with FDB
nexthops:
# ip nexthop add id 1 via 192.0.2.1 fdb
# ip nexthop add id 2 group 1
Error: Non FDB nexthop group cannot have fdb nexthops.
And vice versa:
# ip nexthop add id 3 via 192.0.2.2 dev dummy1
# ip nexthop add id 4 group 3 fdb
Error: FDB nexthop group can only have fdb nexthops.
However, as long as no routes are pointing to a non-FDB nexthop group,
the kernel allows changing the type of a nexthop from FDB to non-FDB and
vice versa:
# ip nexthop add id 5 via 192.0.2.2 dev dummy1
# ip nexthop add id 6 group 5
# ip nexthop replace id 5 via 192.0.2.2 fdb
# echo $?
0
This configuration is invalid and can result in a NPD [1] since FDB
nexthops are not associated with a nexthop device:
# ip route add 198.51.100.1/32 nhid 6
# ping 198.51.100.1
Fix by preventing nexthop FDB status change while the nexthop is in a
group:
# ip nexthop add id 7 via 192.0.2.2 dev dummy1
# ip nexthop add id 8 group 7
# ip nexthop replace id 7 via 192.0.2.2 fdb
Error: Cannot change nexthop FDB status while in a group.
[1]
BUG: kernel NULL pointer dereference, address: 00000000000003c0
[...]
Oops: Oops: 0000 [#1] SMP
CPU: 6 UID: 0 PID: 367 Comm: ping Not tainted 6.17.0-rc6-virtme-gb65678cacc03 #1 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014
RIP: 0010:fib_lookup_good_nhc+0x1e/0x80
[...]
Call Trace:
<TASK>
fib_table_lookup+0x541/0x650
ip_route_output_key_hash_rcu+0x2ea/0x970
ip_route_output_key_hash+0x55/0x80
__ip4_datagram_connect+0x250/0x330
udp_connect+0x2b/0x60
__sys_connect+0x9c/0xd0
__x64_sys_connect+0x18/0x20
do_syscall_64+0xa4/0x2a0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Fixes: 38428d68719c ("nexthop: support for fdb ecmp nexthops")
Reported-by: syzbot+6596516dd2b635ba2350@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/68c9a4d2.050a0220.3c6139.0e63.GAE@google.com/
Tested-by: syzbot+6596516dd2b635ba2350@syzkaller.appspotmail.com
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250921150824.149157-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, alloc_skb_with_frags() will only fill (MAX_SKB_FRAGS - 1)
slots. I think it should use all MAX_SKB_FRAGS slots, as callers of
alloc_skb_with_frags() will size their allocation of frags based
on MAX_SKB_FRAGS.
This issue was discovered via a test patch that sets 'order' to 0
in alloc_skb_with_frags(), which effectively tests/simulates high
fragmentation. In this case sendmsg() on unix sockets will fail every
time for large allocations. If the PAGE_SIZE is 4K, then data_len will
request 68K or 17 pages, but alloc_skb_with_frags() can only allocate
64K in this case or 16 pages.
Fixes: 09c2c90705bb ("net: allow alloc_skb_with_frags() to allocate bigger packets")
Signed-off-by: Jason Baron <jbaron@akamai.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250922191957.2855612-1-jbaron@akamai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
busylock was protecting UDP sockets against packet floods,
but unfortunately was not protecting the host itself.
Under stress, many cpus could spin while acquiring the busylock,
and NIC had to drop packets. Or packets would be dropped
in cpu backlog if RPS/RFS were in place.
This patch replaces the busylock by intermediate
lockless queues. (One queue per NUMA node).
This means that fewer number of cpus have to acquire
the UDP receive queue lock.
Most of the cpus can either:
- immediately drop the packet.
- or queue it in their NUMA aware lockless queue.
Then one of the cpu is chosen to process this lockless queue
in a batch.
The batch only contains packets that were cooked on the same
NUMA node, thus with very limited latency impact.
Tested:
DDOS targeting a victim UDP socket, on a platform with 6 NUMA nodes
(Intel(R) Xeon(R) 6985P-C)
Before:
nstat -n ; sleep 1 ; nstat | grep Udp
Udp6InDatagrams 1004179 0.0
Udp6InErrors 3117 0.0
Udp6RcvbufErrors 3117 0.0
After:
nstat -n ; sleep 1 ; nstat | grep Udp
Udp6InDatagrams 1116633 0.0
Udp6InErrors 14197275 0.0
Udp6RcvbufErrors 14197275 0.0
We can see this host can now proces 14.2 M more packets per second
while under attack, and the victim socket can receive 11 % more
packets.
I used a small bpftrace program measuring time (in us) spent in
__udp_enqueue_schedule_skb().
Before:
@udp_enqueue_us[398]:
[0] 24901 |@@@ |
[1] 63512 |@@@@@@@@@ |
[2, 4) 344827 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@|
[4, 8) 244673 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[8, 16) 54022 |@@@@@@@@ |
[16, 32) 222134 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[32, 64) 232042 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[64, 128) 4219 | |
[128, 256) 188 | |
After:
@udp_enqueue_us[398]:
[0] 5608855 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@|
[1] 1111277 |@@@@@@@@@@ |
[2, 4) 501439 |@@@@ |
[4, 8) 102921 | |
[8, 16) 29895 | |
[16, 32) 43500 | |
[32, 64) 31552 | |
[64, 128) 979 | |
[128, 256) 13 | |
Note that the remaining bottleneck for this platform is in
udp_drops_inc() because we limited struct numa_drop_counters
to only two nodes so far.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250922104240.2182559-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge the xdp_pull_data stable branch into the master branch. No conflict.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
Merge the xdp_pull_data stable branch into the net branch. No conflict.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
|
|
To test bpf_xdp_pull_data(), an xdp packet containing fragments as well
as free linear data area after xdp->data_end needs to be created.
However, bpf_prog_test_run_xdp() always fills the linear area with
data_in before creating fragments, leaving no space to pull data. This
patch will allow users to specify the linear data size through
ctx->data_end.
Currently, ctx_in->data_end must match data_size_in and will not be the
final ctx->data_end seen by xdp programs. This is because ctx->data_end
is populated according to the xdp_buff passed to test_run. The linear
data area available in an xdp_buff, max_linear_sz, is alawys filled up
before copying data_in into fragments.
This patch will allow users to specify the size of data that goes into
the linear area. When ctx_in->data_end is different from data_size_in,
only ctx_in->data_end bytes of data will be put into the linear area when
creating the xdp_buff.
While ctx_in->data_end will be allowed to be different from data_size_in,
it cannot be larger than the data_size_in as there will be no data to
copy from user space. If it is larger than the maximum linear data area
size, the layout suggested by the user will not be honored. Data beyond
max_linear_sz bytes will still be copied into fragments.
Finally, since it is possible for a NIC to produce a xdp_buff with empty
linear data area, allow it when calling bpf_test_init() from
bpf_prog_test_run_xdp() so that we can test XDP kfuncs with such
xdp_buff. This is done by moving lower-bound check to callers as most of
them already do except bpf_prog_test_run_skb(). The change also fixes a
bug that allows passing an xdp_buff with data < ETH_HLEN. This can
happen when ctx is used and metadata is at least ETH_HLEN.
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250922233356.3356453-7-ameryhung@gmail.com
|
|
Change the variable naming in bpf_prog_test_run_xdp() to make the
overall logic less confusing. As different modes were added to the
function over the time, some variables got overloaded, making
it hard to understand and changing the code becomes error-prone.
Replace "size" with "linear_sz" where it refers to the size of metadata
and data. If "size" refers to input data size, use test.data_size_in
directly.
Replace "max_data_sz" with "max_linear_sz" to better reflect the fact
that it is the maximum size of metadata and data (i.e., linear_sz). Also,
xdp_rxq.frags_size is always PAGE_SIZE, so just set it directly instead
of subtracting headroom and tailroom and adding them back.
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250922233356.3356453-6-ameryhung@gmail.com
|
|
Add kfunc, bpf_xdp_pull_data(), to support pulling data from xdp
fragments. Similar to bpf_skb_pull_data(), bpf_xdp_pull_data() makes
the first len bytes of data directly readable and writable in bpf
programs. If the "len" argument is larger than the linear data size,
data in fragments will be copied to the linear data area when there
is enough room. Specifically, the kfunc will try to use the tailroom
first. When the tailroom is not enough, metadata and data will be
shifted down to make room for pulling data.
A use case of the kfunc is to decapsulate headers residing in xdp
fragments. It is possible for a NIC driver to place headers in xdp
fragments. To keep using direct packet access for parsing and
decapsulating headers, users can pull headers into the linear data
area by calling bpf_xdp_pull_data() and then pop the header with
bpf_xdp_adjust_head().
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20250922233356.3356453-4-ameryhung@gmail.com
|
|
Move skb_frag_t adjustment into bpf_xdp_shrink_data() and extend its
functionality to be able to shrink an xdp fragment from both head and
tail. In a later patch, bpf_xdp_pull_data() will reuse it to shrink an
xdp fragment from head.
Additionally, in bpf_xdp_frags_shrink_tail(), breaking the loop when
bpf_xdp_shrink_data() returns false (i.e., not releasing the current
fragment) is not necessary as the loop condition, offset > 0, has the
same effect. Remove the else branch to simplify the code.
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250922233356.3356453-3-ameryhung@gmail.com
|
|
It is possible for bpf_xdp_adjust_tail() to free all fragments. The
kfunc currently clears the XDP_FLAGS_HAS_FRAGS bit, but not
XDP_FLAGS_FRAGS_PF_MEMALLOC. So far, this has not caused a issue when
building sk_buff from xdp_buff since all readers of xdp_buff->flags
use the flag only when there are fragments. Clear the
XDP_FLAGS_FRAGS_PF_MEMALLOC bit as well to make the flags correct.
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250922233356.3356453-2-ameryhung@gmail.com
|
|
This was the last caller of xdr_set_scratch_page(), so I remove this
function while I'm at it.
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
|
|
The only snag here is that __folio_alloc_node() doesn't handle
NUMA_NO_NODE, so I also need to update svc_pool_map_get_node() to return
numa_mem_id() instead. I arrived at this approach by looking at what
other users of __folio_alloc_node() do for this case.
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
|
|
GFP_NOWAIT already includes __GFP_NOWARN, so let's remove the redundant
__GFP_NOWARN.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
|
|
Clean up: because svc_rpcb_cleanup() and svc_xprt_destroy_all()
are always invoked in pairs, we can deduplicate code by moving
the svc_rpcb_cleanup() call sites into svc_xprt_destroy_all().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Olga Kornievskaia <okorniev@redhat.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
|
|
We have a lot of old dprintk() call sites that aren't going anywhere
anytime soon. At the same time, turning them up is a serious burden on
the host due to the console locking overhead.
Add a new Kconfig option that redirects dfprintk() output to the trace
buffer. This is more efficient than logging to the console and allows
for proper interleaving of dprintk and static tracepoint events.
Since using trace_printk() causes scary warnings to pop at boot time,
this new option defaults to "n".
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
|
|
kern_path_locked() is now only used to prepare for removing an object
from the filesystem (and that is the only credible reason for wanting a
positive locked dentry). Thus it corresponds to kern_path_create() and
so should have a corresponding name.
Unfortunately the name "kern_path_create" is somewhat misleading as it
doesn't actually create anything. The recently added
simple_start_creating() provides a better pattern I believe. The
"start" can be matched with "end" to bracket the creating or removing.
So this patch changes names:
kern_path_locked -> start_removing_path
kern_path_create -> start_creating_path
user_path_create -> start_creating_user_path
user_path_locked_at -> start_removing_user_path_at
done_path_create -> end_creating_path
and also introduces end_removing_path() which is identical to
end_creating_path().
__start_removing_path (which was __kern_path_locked) is enhanced to
call mnt_want_write() for consistency with the start_creating_path().
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Add defines for all event types and subtypes an ism device is known to
produce as it can be helpful for debugging purposes.
Introduces a generic 'struct dibs_event' and adopt ism device driver
and smc-d client accordingly. Tolerate and ignore other type and subtype
values to enable future device extensions.
SMC-D and ISM are now independent.
struct ism_dev can be moved to drivers/s390/net/ism.h.
Note that in smc, the term 'ism' is still used. Future patches could
replace that with 'dibs' or 'smc-d' as appropriate.
Signed-off-by: Julian Ruess <julianr@linux.ibm.com>
Co-developed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-15-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use struct dibs_dmb instead of struct smc_dmb and move the corresponding
client tables to dibs_dev. Leave driver specific implementation details
like sba in the device drivers.
Register and unregister dmbs via dibs_dev_ops. A dmb is dedicated to a
single client, but a dibs device can have dmbs for more than one client.
Trigger dibs clients via dibs_client_ops->handle_irq(), when data is
received into a dmb. For dibs_loopback replace scheduling an smcd receive
tasklet with calling dibs_client_ops->handle_irq().
For loopback devices attach_dmb(), detach_dmb() and move_data() need to
access the dmb tables, so move those to dibs_dev_ops in this patch as well.
Remove remaining definitions of smc_loopback as they are no longer
required, now that everything is in dibs_loopback.
Note that struct ism_client and struct ism_dev are still required in smc
until a follow-on patch moves event handling to dibs. (Loopback does not
use events).
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-14-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Provide the dibs_dev_ops->query_remote_gid() in ism and dibs_loopback
dibs_devices. And call it in smc dibs_client.
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-13-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
It can be debated how much benefit definition of vlan ids for dibs devices
brings, as the dmbs are accessible only by a single peer anyhow. But ism
provides vlan support and smcd exploits it, so move it to dibs layer as an
optional feature.
smcd_loopback simply ignores all vlan settings, do the same in
dibs_loopback.
SMC-D and ISM have a method to use the invalid VLAN ID 1FFF
(ISM_RESERVED_VLANID), to indicate that both communication peers support
routable SMC-Dv2. Tolerate it in dibs, but move it to SMC only.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-12-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Define a uuid_t GID attribute to identify a dibs device.
SMC uses 64 Bit and 128 Bit Global Identifiers (GIDs) per device, that
need to be sent via the SMC protocol. Because the smc code uses integers,
network endianness and host endianness need to be considered. Avoid this
in the dibs layer by using uuid_t byte arrays. Future patches could change
SMC to use uuid_t. For now conversion helper functions are introduced.
ISM devices provide 64 Bit GIDs. Map them to dibs uuid_t GIDs like this:
_________________________________________
| 64 Bit ISM-vPCI GID | 00000000_00000000 |
-----------------------------------------
If interpreted as UUID [1], this would be interpreted as the UIID variant,
that is reserved for NCS backward compatibility. So it will not collide
with UUIDs that were generated according to the standard.
smc_loopback already uses version 4 UUIDs as 128 Bit GIDs, move that to
dibs loopback. A temporary change to smc_lo_query_rgid() is required,
that will be moved to dibs_loopback with a follow-on patch.
Provide gid of a dibs device as sysfs read-only attribute.
Link: https://datatracker.ietf.org/doc/html/rfc4122 [1]
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-11-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Create '/sys/class/dibs' to represent multiple kinds of dibs devices in
sysfs. Show s390/ism devices as well as dibs_loopback devices.
Show attribute fabric_id using dibs_ops.get_fabric_id(). This can help
users understand which dibs devices are connected to the same fabric in
different systems and which dibs devices are loopback devices
(fabric_id 0xffff)
Instead of using the same name as the pci device, give the ism devices
their own readable names based on uid or fid from the HW definition.
smc_loopback was never visible in sysfs. dibs_loopback is now represented
as a virtual device.
For the SMC feature "software defined pnet-id" either the ib device name or
the PCI-ID (actually the parent device name) can be used for SMC-R entries.
Mimic this behaviour for SMC-D, and check the parent device name as well.
So device name or PCI-ID can be used for ism and device name can be used
for dibs-loopback. Note that this:
IB_DEVICE_NAME_MAX - 1 == smc_pnet_policy.[SMC_PNETID_IBNAME].len
is the length of smcd_name. Future SW-pnetid cleanup patches to could use a
meaningful define, but that would touch too much unrelated code here.
Examples:
---------
ism before:
> ls /sys/bus/pci/devices/0000:00:00.0/0000:00:00.0
uevent
ism now:
> ls /sys/bus/pci/devices/0000:00:00.0/dibs/ism30
device -> ../../../0000:00:00.0/
fabric_id
subsystem -> ../../../../../class/dibs/
uevent
dibs loopback:
> ls /sys/devices/virtual/dibs/lo/
fabric_id
subsystem -> ../../../../class/dibs/
uevent
dibs class:
> ls -l /sys/class/dibs/
ism30 -> ../../devices/pci0000:00/0000:00:00.0/dibs/ism30/
lo -> ../../devices/virtual/dibs/lo/
For comparison:
> ls -l /sys/class/net/
enc8410 -> ../../devices/qeth/0.0.8410/net/enc8410/
ens1693 -> ../../devices/pci0001:00/0001:00:00.0/net/ens1693/
lo -> ../../devices/virtual/net/lo/
Signed-off-by: Julian Ruess <julianr@linux.ibm.com>
Co-developed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-10-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move struct device from ism_dev and smc_lo_dev to dibs_dev, and define a
corresponding release function. Free ism_dev in ism_remove() and smc_lo_dev
in smc_lo_dev_remove().
Replace smcd->ops->get_dev(smcd) by using dibs->dev directly.
An alternative design would be to embed dibs_dev as a field in ism_dev and
do the same for other dibs device driver specific structs. However that
would have the disadvantage that each dibs device driver needs to allocate
dibs_dev and each dibs device driver needs a different device release
function. The advantage would be that ism_dev and other device driver
specific structs would be covered by device reference counts.
Signed-off-by: Julian Ruess <julianr@linux.ibm.com>
Co-developed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-9-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move the device add() and remove() functions from ism_client to
dibs_client_ops and call add_dev()/del_dev() for ism devices and
dibs_loopback devices. dibs_client_ops->add_dev() = smcd_register_dev() for
the smc_dibs_client. This is the first step to handle ism and loopback
devices alike (as dibs devices) in the smc dibs client.
Define dibs_dev->ops and move smcd_ops->get_chid to
dibs_dev_ops->get_fabric_id() for ism and loopback devices. See below for
why this needs to be in the same patch as dibs_client_ops->add_dev().
The following changes contain intermediate steps, that will be obsoleted by
follow-on patches, once more functionality has been moved to dibs:
Use different smcd_ops and max_dmbs for ism and loopback. Follow-on patches
will change SMC-D to directly use dibs_ops instead of smcd_ops.
In smcd_register_dev() it is now necessary to identify a dibs_loopback
device before smcd_dev and smcd_ops->get_chid() are available. So provide
dibs_dev_ops->get_fabric_id() in this patch and evaluate it in
smc_ism_is_loopback().
Call smc_loopback_init() in smcd_register_dev() and call
smc_loopback_exit() in smcd_unregister_dev() to handle the functionality
that is still in smc_loopback. Follow-on patches will move all smc_loopback
code to dibs_loopback.
In smcd_[un]register_dev() use only ism device name, this will be replaced
by dibs device name by a follow-on patch.
End of changes with intermediate parts.
Allocate an smcd event workqueue for all dibs devices, although
dibs_loopback does not generate events.
Use kernel memory instead of devres memory for smcd_dev and smcd->conn.
Since commit a72178cfe855 ("net/smc: Fix dependency of SMC on ISM") an ism
device and its driver can have a longer lifetime than the smc module, so
smc should not rely on devres to free its resources [1]. It is now the
responsibility of the smc client to free smcd and smcd->conn for all dibs
devices, ism devices as well as loopback. Call client->ops->del_dev() for
all existing dibs devices in dibs_unregister_client(), so all device
related structures can be freed in the client.
When dibs_unregister_client() is called in the context of smc_exit() or
smc_core_reboot_event(), these functions have already called
smc_lgrs_shutdown() which calls smc_smcd_terminate_all(smcd) and sets
going_away. This is done a second time in smcd_unregister_dev(). This is
analogous to how smcr is handled in these functions, by calling first
smc_lgrs_shutdown() and then smc_ib_unregister_client() >
smc_ib_remove_dev(), so leave it that way. It may be worth investigating,
whether smc_lgrs_shutdown() is still required or useful.
Remove CONFIG_SMC_LO. CONFIG_DIBS_LO now controls whether a dibs loopback
device exists or not.
Link: https://www.kernel.org/doc/Documentation/driver-model/devres.txt [1]
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-8-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Formally register smc as dibs client. Functionality will be moved by
follow-on patches from ism_client to dibs_client until eventually
ism_client can be removed.
As DIBS is only a shim layer without any dependencies, we can depend SMC
on DIBS without adding indirect dependencies. A follow-on patch will
remove dependency of SMC on ISM.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-5-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Create the file structure for a 'DIBS - Direct Internal Buffer Sharing'
shim layer that will provide generic functionality and declarations for
dibs device drivers and dibs clients.
Following patches will add functionality.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20250918110500.1731261-4-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before this patch there was the following assumption in
smc_loopback.c>smc_lo_move_data():
sf (signalling flag) == 0 : data is already in an attached target dmb
sf == 1 : data is not yet in the target dmb
This is true for the 2 callers in smc client
smcd_cdc_msg_send() : sf=1
smcd_tx_rdma_writes() : sf=0
but should not be a general assumption.
Add a bool to struct smc_buf_desc to indicate whether an SMC-D sndbuf_desc
is an attached buffer. Don't call move_data() for attached send_buffers,
because it is not necessary.
Move the data in smc_lo_move_data() if len != 0 and signal when requested.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Link: https://patch.msgid.link/20250918110500.1731261-3-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
smcd_buf_free() calls smc_ism_unregister_dmb(lgr->smcd, buf_desc) and
then unconditionally frees buf_desc.
Remove the cleaning up of fields of buf_desc in
smc_ism_unregister_dmb(), because it is not helpful.
This removes the only usage of ISM_ERROR from the smc module. So move it
to drivers/s390/net/ism.h.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Mahanta Jambigi <mjambigi@linux.ibm.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Link: https://patch.msgid.link/20250918110500.1731261-2-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Today, once an inet_bind_bucket enters a state where fastreuse >= 0 or
fastreuseport >= 0 after a socket is explicitly bound to a port, it remains
in that state until all sockets are removed and the bucket is destroyed.
In this state, the bucket is skipped during ephemeral port selection in
connect(). For applications using a reduced ephemeral port
range (IP_LOCAL_PORT_RANGE socket option), this can cause faster port
exhaustion since blocked buckets are excluded from reuse.
The reason the bucket state isn't updated on port release is unclear.
Possibly a performance trade-off to avoid scanning bucket owners, or just
an oversight.
Fix it by recalculating the bucket state when a socket releases a port. To
limit overhead, each inet_bind2_bucket stores its own (fastreuse,
fastreuseport) state. On port release, only the relevant port-addr bucket
is scanned, and the overall state is derived from these.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250917-update-bind-bucket-state-on-unhash-v5-1-57168b661b47@cloudflare.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As hinted in commit 501a90c94510 ("inet: protect against too small mtu
values."), net_device->mtu is vulnerable to race conditions if it is
written and read without holding the RTNL.
At the moment, all the writes are done while the interface is down,
either in the devices' probe() function or in can_changelink(). So
there are no such issues yet. But upcoming changes will allow to
modify the MTU while the CAN XL devices are up.
In preparation to the introduction of CAN XL, annotate all the
net_device->mtu accesses which are not yet guarded by the RTNL with a
READ_ONCE().
Note that all the write accesses are already either guarded by the
RTNL or are already annotated and thus need no changes.
Signed-off-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/20250923-can-fix-mtu-v3-1-581bde113f52@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The original code used nl80211_chan_width_to_mhz(), which returns the width in MHz.
However, the expected unit is KHz.
Fixes: 510dba80ed66 ("wifi: cfg80211: add helper for checking if a chandef is valid on a radio")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://patch.msgid.link/df54294e6c4ed0f3ceff6e818b710478ddfc62c0.1758579480.git.Ryder%20Lee%20ryder.lee@mediatek.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
synflood_warned had to be u32 for xchg(), but ensuring
atomicity is not really needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250919204856.2977245-9-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tp->tcp_clean_acked is fetched in tx path when snd_una is updated.
This field thus belongs to tcp_sock_read_tx group.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250919204856.2977245-7-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_ack() writes this field, it belongs to tcp_sock_write_txrx.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250919204856.2977245-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Maintaining the CACHELINE_ASSERT_GROUP_SIZE() uses
for struct tcp_sock has been painful.
This had little benefit, so remove them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250919204856.2977245-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sk->sk_sndbuf is read-mostly in tx path, so move it from
sock_write_tx group to more appropriate sock_read_tx.
sk->sk_err_soft was not identified previously, but
is used from tcp_ack().
Move it to sock_write_tx group for better cache locality.
Also change tcp_ack() to clear sk->sk_err_soft only if needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250919204856.2977245-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
sk_uid and sk_protocol are read from inet6_csk_route_socket()
for each TCP transmit.
Also read from udpv6_sendmsg(), udp_sendmsg() and others.
Move them to sock_read_tx for better cache locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250919204856.2977245-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change adds a new WQ_PERCPU flag at the network subsystem, to explicitly
request the use of the per-CPU behavior. Both flags coexist for one release
cycle to allow callers to transition their calls.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
All existing users have been updated accordingly.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20250918142427.309519-4-marco.crivellari@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
system_unbound_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
Adding system_dfl_wq to encourage its use when unbound work should be used.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20250918142427.309519-3-marco.crivellari@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
system_unbound_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
Adding system_dfl_wq to encourage its use when unbound work should be used.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20250918142427.309519-2-marco.crivellari@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2025-09-22
1) Fix 0 assignment for SPIs. 0 is not a valid SPI,
it means no SPI assigned.
2) Fix offloading for inter address family tunnels.
* tag 'ipsec-2025-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
xfrm: fix offloading of cross-family tunnels
xfrm: xfrm_alloc_spi shouldn't use 0 as SPI
====================
Link: https://patch.msgid.link/20250922073512.62703-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When working on a fix modifying mptcp_check_data_fin(), I noticed the
returned value was no longer used.
It looks like it was used for 3 days, between commit 7ed90803a213
("mptcp: send explicit ack on delayed ack_seq incr") and commit
ea4ca586b16f ("mptcp: refine MPTCP-level ack scheduling").
This returned value can be safely removed.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250919-net-next-mptcp-server-side-flag-v1-6-a97a5d561a8b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that such info is in the 'flags' attribute, it is time to deprecate
the dedicated 'server-side' attribute.
It will be removed in a few versions.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250919-net-next-mptcp-server-side-flag-v1-3-a97a5d561a8b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the 'flags' attribute is used, it seems interesting to add one
flag for 'server-side', a boolean value.
This is duplicating the info from the dedicated 'server-side' attribute,
but it will be deprecated in the next commit, and removed in a few
versions.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250919-net-next-mptcp-server-side-flag-v1-2-a97a5d561a8b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This attribute is a boolean. No need to add it to set it to 'false'.
Indeed, the default value when this attribute is not set is naturally
'false'. A few bytes can then be saved by not adding this attribute if
the connection is not on the server side.
This prepares the future deprecation of its attribute, in favour of a
new flag.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250919-net-next-mptcp-server-side-flag-v1-1-a97a5d561a8b@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
inet_unhash() checks sk_unhashed() twice at the entry and after locking
ehash/lhash bucket.
The former was somehow added redundantly by commit 4f9bf2a2f5aa ("tcp:
Don't acquire inet_listen_hashbucket::lock with disabled BH.").
inet_unhash() is called for the full socket from 4 places, and it is
always under lock_sock() or the socket is not yet published to other
threads:
1. __sk_prot_rehash()
-> called from inet_sk_reselect_saddr(), which has
lockdep_sock_is_held()
2. sk_common_release()
-> called when inet_create() or inet6_create() fail, then the
socket is not yet published
3. tcp_set_state()
-> calls tcp_call_bpf_2arg(), and tcp_call_bpf() has
sock_owned_by_me()
4. inet_ctl_sock_create()
-> creates a kernel socket and unhashes it immediately, but TCP
socket is not hashed in sock_create_kern() (only SOCK_RAW is)
So we do not need to check sk_unhashed() twice before/after ehash/lhash
lock in inet_unhash().
Let's remove the 2nd one.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250919083706.1863217-4-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
inet_hash() and inet6_hash() are exactly the same.
Also, we do not need to export inet6_hash().
Let's consolidate the two into __inet_hash() and rename it to inet_hash().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250919083706.1863217-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__inet_hash() is called from inet_hash() and inet6_hash with osk NULL.
Let's remove the 2nd arg from __inet_hash().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250919083706.1863217-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
