| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- hci_conn: Fix null ptr deref in hci_abort_conn()
- af_bluetooth: fix UAF in bt_accept_dequeue()
- L2CAP: validate option length before reading conf opt value
- L2CAP: cancel pending_rx_work before taking conn->lock
- L2CAP: Fix use-after-free in l2cap_sock_new_connection_cb()
- L2CAP: fix tx ident leak for commands without a response
- SCO: Fix a race condition in sco_sock_timeout()
- ISO: avoid NULL deref of conn in iso_conn_big_sync()
- ISO: fix malformed ISO_END/CONT handling
- ISO: exclude RFU bits from ISO_SDU_Length
- MGMT: Fix adv monitor add failure cleanup
- MGMT: Fix UAF of hci_conn_params in add_device_complete
- bnep: pin L2CAP connection during netdev registration
- 6lowpan: avoid untracked enable work
- 6lowpan: hold L2CAP conn across debugfs control
- 6lowpan: Fix using chan->conn as indication to no remote netdev
- btintel_pcie: Refactor FLR to use device_reprobe()
- btnxpuart: Fix out-of-bounds firmware read in nxp_recv_fw_req_v3()
- hci_uart: clear HCI_UART_SENDING when write_work is canceled
- bpa10x: avoid OOB read of revision string in bpa10x_setup()
* tag 'for-net-2026-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: fix tx ident leak for commands without a response
Bluetooth: bpa10x: avoid OOB read of revision string in bpa10x_setup()
Bluetooth: ISO: exclude RFU bits from ISO_SDU_Length
Bluetooth: ISO: fix malformed ISO_END/CONT handling
Bluetooth: btintel_pcie: Refactor FLR to use device_reprobe()
Bluetooth: L2CAP: Fix use-after-free in l2cap_sock_new_connection_cb()
Bluetooth: fix UAF in bt_accept_dequeue()
Bluetooth: bnep: pin L2CAP connection during netdev registration
Bluetooth: sco: Fix a race condition in sco_sock_timeout()
Bluetooth: MGMT: Fix adv monitor add failure cleanup
Bluetooth: 6lowpan: hold L2CAP conn across debugfs control
Bluetooth: 6lowpan: avoid untracked enable work
Bluetooth: hci_conn: Fix null ptr deref in hci_abort_conn()
Bluetooth: btnxpuart: Fix out-of-bounds firmware read in nxp_recv_fw_req_v3()
Bluetooth: L2CAP: validate option length before reading conf opt value
Bluetooth: L2CAP: cancel pending_rx_work before taking conn->lock
Bluetooth: ISO: avoid NULL deref of conn in iso_conn_big_sync()
Bluetooth: MGMT: Fix UAF of hci_conn_params in add_device_complete
Bluetooth: 6lowpan: Fix using chan->conn as indication to no remote netdev
Bluetooth: hci_uart: clear HCI_UART_SENDING when write_work is canceled
====================
Link: https://patch.msgid.link/20260706145229.728127-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Sprinkle a few asserts about ops lock: netif_close_many and __dev_notify_flags
should now consistently run under the lock
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260702224150.3730033-6-sdf@fomichev.me
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
rtnl_configure_link calls __dev_change_flags() and __dev_notify_flags,
both need the instance lock. rtnl_newlink_create grabs it but stacked
devices do not. Move the lock inside rtnl_configure_link.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260702224150.3730033-5-sdf@fomichev.me
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
netif_close_many will soon assert ops lock (for locked DOWN/GOING_DOWN).
Update dsa_switch_shutdown to manually grab and release the ops lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260702224150.3730033-3-sdf@fomichev.me
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Mirror what call_netdevice_register_net_notifiers does but for the
teardown. Cover only DOWN and GOING_DOWN. UNREGISTER is still unlocked
because of the SW devices using dev_xxx methods.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20260702224150.3730033-2-sdf@fomichev.me
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
cfg80211_is_element_inherited() reads the first data octet of the
candidate element (id = elem->data[0]) to look it up in an extension
non-inheritance list. It does so after testing elem->id, but without
verifying that the element actually has a data octet. A zero-length
extension element (WLAN_EID_EXTENSION with length 0) therefore makes it
read one octet past the end of the element.
_ieee802_11_parse_elems_full() runs this check for every element of a
frame once a non-inheritance context exists -- e.g. while parsing a
per-STA profile of a Multi-Link element in a (re)association response,
or a non-transmitted BSS profile -- so a crafted frame from an AP can
trigger a one-octet slab-out-of-bounds read during element parsing:
BUG: KASAN: slab-out-of-bounds in cfg80211_is_element_inherited
Read of size 1 ... in net/wireless/scan.c
Return early (treat the element as inherited) when an extension element
carries no data, mirroring the existing handling of empty ID lists.
The bug was found by fuzzing ieee802_11_parse_elems_full() under KASAN.
Fixes: f7dacfb11475 ("cfg80211: support non-inheritance element")
Signed-off-by: HE WEI (ギカク) <skyexpoc@gmail.com>
Link: https://patch.msgid.link/20260707094828.16465-1-skyexpoc@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When a device is destroyed under RTNL, ip_mc_destroy_dev() iterates through
the multicast list and calls ip_ma_put() on each membership, scheduling
them for RCU reclamation. However, they are not unlinked from the device's
multicast hash table (mc_hash).
Since the device remains published in dev->ip_ptr until after
ip_mc_destroy_dev() completes, concurrent RCU readers traversing mc_hash
can still locate and access the multicast group after its refcount is
decremented. If the RCU callback runs and frees the group while a reader is
accessing it, a use-after-free occurs.
Fix this by unlinking the multicast group from mc_hash using
ip_mc_hash_remove() before scheduling it for reclamation.
BUG: KASAN: slab-use-after-free in ip_check_mc_rcu+0x149/0x3f0
Read of size 4 at addr ffff888009bf1408 by task mausezahn/2276
Call Trace:
<IRQ>
dump_stack_lvl+0x67/0x90
print_report+0x175/0x7c0
kasan_report+0x147/0x180
ip_check_mc_rcu+0x149/0x3f0
udp_v4_early_demux+0x36d/0x12d0
ip_rcv_finish_core+0xb8b/0x1390
ip_rcv_finish+0x54/0x120
NF_HOOK+0x213/0x2b0
__netif_receive_skb+0x126/0x340
process_backlog+0x4f2/0xf00
__napi_poll+0x92/0x2c0
net_rx_action+0x583/0xc60
handle_softirqs+0x236/0x7f0
do_softirq+0x57/0x80
</IRQ>
Allocated by task 2239:
kasan_save_track+0x3e/0x80
__kasan_kmalloc+0x72/0x90
____ip_mc_inc_group+0x31a/0xa40
__ip_mc_join_group+0x334/0x3f0
do_ip_setsockopt+0x16fa/0x2010
ip_setsockopt+0x3f/0x90
do_sock_setsockopt+0x1ad/0x300
Freed by task 0:
kasan_save_track+0x3e/0x80
kasan_save_free_info+0x40/0x50
__kasan_slab_free+0x3a/0x60
__rcu_free_sheaf_prepare+0xd4/0x220
rcu_free_sheaf+0x36/0x190
rcu_core+0x8d9/0x12f0
handle_softirqs+0x236/0x7f0
Fixes: e9897071350b ("igmp: hash a hash table to speedup ip_check_mc_rcu()")
Cc: stable@vger.kernel.org
Signed-off-by: Yuyang Huang <yuyanghuang@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260701235014.73505-1-yuyanghuang@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This commit makes use of the building blocks previously added to
implement cross-device rate nodes.
A new 'supported_cross_device_rate_nodes' bool is added to devlink_ops
which lets drivers advertise support for cross-device rate objects.
If enabled and if there is a common shared devlink instance, then:
- all rate objects will be stored in the top-most common nested instance
and
- rate objects can have parents from other devices sharing the same
common instance.
Storing rates in the common shared ancestor is safe, because it is
reference counted by its nested devlink instances, so it's guaranteed to
outlive them. Furthermore, the shared devlink infra guarantees a given
nested devlink hierarchy is managed by the same driver.
The parent devlink from info->ctx is not locked, so none of its mutable
fields can be used. But parent setting only requires comparing devlink
pointer comparisons. Additionally, since the shared devlink is locked,
other rate operations cannot concurrently happen.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260701073254.754518-8-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, a devlink rate's parent device is assumed to be the same as
the one where the devlink rate is created.
This patch changes that to allow rate commands to accept an additional
argument that specifies the parent dev. This will allow devlink rate
groups with leafs from other devices.
Example of the new usage with ynl:
Creating a group on pci/0000:08:00.1 with a parent to an already
existing pci/0000:08:00.1/group1:
./tools/net/ynl/pyynl/cli.py --spec \
Documentation/netlink/specs/devlink.yaml --do rate-new --json '{
"bus-name": "pci",
"dev-name": "0000:08:00.1",
"rate-node-name": "group2",
"rate-parent-node-name": "group1",
"parent-dev": {
"bus-name": "pci",
"dev-name": "0000:08:00.1"
}
}'
Setting the parent of leaf node pci/0000:08:00.1/65537 to
pci/0000:08:00.0/group1:
./tools/net/ynl/pyynl/cli.py --spec \
Documentation/netlink/specs/devlink.yaml --do rate-set --json '{
"bus-name": "pci",
"dev-name": "0000:08:00.1",
"port-index": 65537,
"parent-dev": {
"bus-name": "pci",
"dev-name": "0000:08:00.0"
},
"rate-parent-node-name": "group1"
}'
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260701073254.754518-7-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Upcoming changes to the rate commands need the parent devlink specified.
This change adds a nested 'parent-dev' attribute to the API and helpers
to obtain and put a reference to the parent devlink instance in
info->ctx.
To avoid deadlocks, the parent devlink is unlocked before obtaining the
main devlink instance that is the target of the request.
A reference to the parent is kept until the end of the request to avoid
it suddenly disappearing.
This means that this reference is of limited use without additional
protection.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260701073254.754518-6-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Devlink rate leafs and nodes were stored in their respective devlink
objects pointed to by devlink_rate->devlink.
This patch removes that association by introducing the concept of
'rate node devlink', which is where all rates that could link to each
other are stored. For now this is the same as devlink_rate->devlink.
After this patch, the devlink rates stored in this devlink instance
could potentially be from multiple other devlink instances. So all rate
node manipulation code was updated to:
- correctly compare the actual devlink object during iteration.
- maybe acquire additional locks (noop for now).
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260701073254.754518-5-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Replace deprecated info->user_ptr[0]/[1] with a typed
devlink_nl_ctx struct stored in info->ctx. The struct aliases
the same union memory, so the migration is safe.
There are no functionality changes here.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260701073254.754518-4-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Upcoming code will need to obtain references to locked nested-in
devlink instances. Add a helper to lock, reference and return the
nested-in instance.
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260701073254.754518-3-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 8e133ba99cd8 ("net: fib_rules: Add fib_rules_ops.lock.")
added mutex in struct fib_rules_ops, which is initialised in
fib_rules_register().
Let's add paired mutex_destroy() in fib_rules_unregister().
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260702044437.591864-3-kuniyu@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When CONFIG_IP_MULTIPLE_TABLES is disabled, fib_new_table()
is fib_get_table(), and no new table is created.
Let's move net->ipv4.fib_table_hash_lock under
CONFIG_IP_MULTIPLE_TABLES.
While at it, netns_ipv4_sysctl.rst is updated.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260702044437.591864-2-kuniyu@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
An association request or response frame is generally delivered to the
driver without a TX queue object. However, with drivers that do encryption
offload and couple the key with a transmit queue, this means that the
frames are not being encrypted.
Fix this by routing the association frames to the management TXQ.
This will allow the driver to set up the required resources before
transmitting the association frame, e.g., set up keys etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260706222925.febcc62f485c.Iff932880e4b98232cbf6ba405fbb90d650a85381@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A peer may send a zero-length TLS application_data record; TLS 1.3
explicitly permits these as a traffic-analysis countermeasure (RFC
8446, Section 5.1). After decryption such a record has full_len ==
0. tls_sw_read_sock() hands it to the read_actor, which has no
payload to consume and returns zero. The loop treats a zero return
as backpressure (used <= 0), requeues the skb at the head of
rx_list, and stops. rx_list is serviced head-first on the next
call, so the empty record is dequeued, fails the same way, and is
requeued again; every later record on the connection is blocked
behind it.
tls_sw_recvmsg() does not stall on this: a zero-length data record
copies nothing and falls through to consume_skb(). Mirror that in
the read_sock() path by recognizing an empty data record before
the actor runs, consuming it, and continuing.
Fixes: 662fbcec32f4 ("net/tls: implement ->read_sock()")
Signed-off-by: Chuck Lever <cel@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20260630191551.875664-1-cel@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
cfg80211_rx_assoc_resp() initialises the status and response-IE fields
of cfg80211_connect_resp_params from the management frame before
proving that the frame is long enough for those offsets. S1G and
regular association responses also have different IE offsets, but the
S1G path only patched resp_ie after the unsafe initialiser had already
run.
Defer resp_ie, resp_ie_len, and status to after the link-iteration
loop. Use a bool to remember whether the frame is S1G, then validate
the appropriate minimum length and set all three fields in a single
if/else block. Funnel short-frame and SME-reject cleanup through a
shared free_bss label for the abandon paths.
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260707025336.22557-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
cfg80211_rx_mlme_mgmt() and cfg80211_tx_mlme_mgmt() call tracepoints
before rejecting frames shorter than the frame-control field. After
that, they only require len >= 2 before dispatching into subtype
handlers that assume their fixed fields are present.
The frames that trip this are not shorter than 2 bytes; they are short
relative to their subtype. mwifiex is a concrete in-tree example on the
length side: mwifiex_process_mgmt_packet() only requires a 4-address
ieee80211_hdr plus the 2-byte firmware length prefix before handing the
frame to cfg80211_rx_mlme_mgmt(). After stripping the length prefix and
removing addr4, pkt_len can be exactly 24: a bare 3-address management
header with no reason-code body. The existing WARN_ON(len < 2) does not
fire on such a frame, and cfg80211_process_deauth() then reads
u.deauth.reason_code as a two-byte access starting at offset 24,
immediately past the 24-byte buffer.
Add a frame-control length gate, then validate each subtype's minimum
frame size in an if/else-if chain that mirrors the dispatch logic. Trace
only after the frame is known to be well-formed.
Side effects of this change:
- The WARN_ON(len < 2) is dropped. It only guarded the frame_control
read, never the subtype fixed fields, and it does not fire on the
frames that actually trigger the out-of-bounds read (which are >= 2).
The len >= 2 check is kept as the guard before dereferencing
frame_control, but without the warning: these are exported callbacks
and a malformed frame from a driver should be dropped silently rather
than backtraced.
- cfg80211_tx_mlme_mgmt() previously routed every non-deauth subtype
through disassociation handling; it now silently ignores unrecognised
subtypes.
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260707025336.22557-1-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
While leaving an IBSS in ieee80211_ibss_disconnect() mac80211 flushes
stations, turns the carrier off and immediately tells the driver to
leave as well. While there may be synchronize_net() in station flush
and in this code later, packets can still be transmitted due to
cross-CPU race conditions after carrier off is set.
Therefore, it's possible for a race to happen where a TX to the
driver occurs while or after telling it to leave the IBSS. This can
be confusing to drivers, and in the case of iwlwifi leads to an
attempt to use invalid queues.
Move netif_carrier_off() to occur before sta_info_flush() during
IBSS disconnect, and add synchronize_net() if flushing didn't,
so that the synchronize_net() always happens between turning the
carrier off and telling the driver, avoiding this race.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260706223751.da1ce439cc93.If5cf482f87ab98ce66dd48724e24c81fed236d3f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When IBSS peer capabilities change, rates_updated is set to true in
ieee80211_update_sta_info(), but rx_nss is never recalculated.
For peers with HT/VHT, this leaves rx_nss at 0 instead of the
correct value, causing drivers to use incorrect rate scaling
parameters.
The root cause is that the commit below moved NSS initialisation
out of rate_control_rate_init() into explicit call sites, but
missing the rates_updated path in ieee80211_update_sta_info().
Fix this by calling ieee80211_sta_init_nss_bw_capa() before
rate_control_rate_init() when peer capabilities are updated,
consistent with the other IBSS call sites added by that commit.
Fixes: e5ad38a9b261 ("wifi: mac80211: clean up STA NSS handling")
Signed-off-by: Shahar Tzarfati <shahar.tzarfati@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260706222724.422adfd57b71.I5a47f65c5e38a221712f5203e5c8040304b382b5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
nl80211_netlink_notify() walks the cfg80211 wireless device list when a
NETLINK_GENERIC socket is released. If the socket owns a connection, the
notifier queues the embedded wdev->disconnect_wk work item.
That work is a plain work_struct today. NETDEV_GOING_DOWN cancels it, but a
NETLINK_URELEASE notifier that already observed conn_owner_nlportid can
queue it after that cancel returns. _cfg80211_unregister_wdev() then
removes the wdev from the list and waits for RCU readers, but
synchronize_net() does not drain work queued by such a reader.
Make the autodisconnect work a wiphy_work instead. The callback already
needs the wiphy mutex, and wiphy_work runs under that mutex. This lets
teardown cancel pending autodisconnect work while holding the mutex,
without a cancel_work_sync() vs. worker locking concern.
Also cancel the wiphy work after list_del_rcu() and synchronize_net(). Any
NETLINK_URELEASE notifier that had already reached the wdev list has then
either queued the work and it is removed, or can no longer find the wdev.
Fixes: bd2522b16884 ("cfg80211: NL80211_ATTR_SOCKET_OWNER support for CMD_CONNECT")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Assisted-by: Codex:gpt-5.5
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Link: https://patch.msgid.link/20260706152418.779226-1-zzzccc427@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If kmemdup() fails while copying supported band structures, the error
path jumps to fail_rate. This skips rate_control_deinitialize() and
leaks the initialized local->rate_ctrl.
Fix this by adding a fail_band label that shares the rate-control cleanup
path before falling through to the remaining teardown.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc7.
An x86_64 allyesconfig build showed no new warnings. As we do not have a
suitable mac80211 device/driver combination to test with, no runtime
testing was able to be performed.
Fixes: 09b4a4faf9d0 ("mac80211: introduce capability flags for VHT EXT NSS support")
Cc: stable@vger.kernel.org
Reviewed-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Link: https://patch.msgid.link/20260706143507.146131-1-dawei.feng@seu.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ieee80211_do_stop() removes AP_VLAN packets from the parent AP
ps->bc_buf while holding ps->bc_buf.lock with IRQs disabled. It then
calls ieee80211_free_txskb() before dropping the lock.
ieee80211_free_txskb() is not just a passive SKB release. For SKBs with
TX status state it can report a dropped frame through cfg80211/nl80211,
and that path can reach netlink tap transmit. This is the same reason
the pending queue cleanup in ieee80211_do_stop() already unlinks SKBs
under the queue lock and frees them after IRQ state is restored.
The buggy scenario involves two paths, with each column showing the
order within that path:
AP_VLAN management TX: AP_VLAN stop:
1. attach ACK-status state 1. clear the running state
2. queue a multicast SKB on 2. take ps->bc_buf.lock with IRQs
parent ps->bc_buf disabled
3. unlink the AP_VLAN SKB
4. call ieee80211_free_txskb()
Unlink matching AP_VLAN SKBs from ps->bc_buf under the existing lock,
but move them to a local free queue. Drop the lock and restore IRQ state
before calling ieee80211_free_txskb().
WARNING: kernel/softirq.c:430 at __local_bh_enable_ip
Fixes: 397a7a24ef8c ("mac80211: free ps->bc_buf skbs on vlan device stop")
Assisted-by: Codex:gpt-5.5
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Link: https://patch.msgid.link/20260706140841.581566-1-zzzccc427@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, when userspace requests station information with
link statistics using NL80211_CMD_GET_STATION with the
NL80211_ATTR_STA_DUMP_LINK_STATS flag, the kernel uses the .doit callback
(nl80211_get_station) which sends a single netlink message. For MLO
stations with multiple links, the link statistics can be large and may
exceed the maximum netlink message size, causing the operation to fail
with -EMSGSIZE.
The .dumpit callback (nl80211_dump_station) already supports
fragmentation across multiple netlink messages, making it suitable
for handling large link statistics. However, it currently iterates over
all stations on the interface, which is inefficient when userspace only
wants information about a specific station.
Add support for MAC address filtering in nl80211_dump_station to allow
userspace to request fragmented link statistics for a specific station.
When NL80211_ATTR_MAC is present in a dump request, cache the MAC address
in the dump context and use rdev_get_station() to retrieve information for
only that station, instead of iterating over all stations with
rdev_dump_station().
This allows userspace tools (like iw) to use NL80211_CMD_GET_STATION with
NLM_F_DUMP flag to retrieve complete link statistics for a specific
station across multiple netlink messages, avoiding the message size
limitation.
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260614051739.3979947-6-praneesh.p@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In MLO scenarios, stations may have multiple links, each with distinct
statistics. When userspace tools like iw or hostapd request station dumps,
attempting to pack all per-link stats into a single netlink message can
easily exceed the default 4KB buffer limit, especially when more than two
links are active. This results in -EMSGSIZE errors and incomplete data
delivery.
To address this, fragment per-link station statistics across multiple
netlink messages to ensure reliable delivery of complete MLO station
information. Extend the stateful context with a two-phase dump mechanism:
phase 0 (AGGREGATED) sends combined MLO-level statistics and phase 1
(PER_LINK) sends individual per-link statistics for each active link.
The dump loop is structured to produce exactly one netlink message per
iteration, with a common header (ifindex, wdev, mac, generation) built
once and phase-specific payload added via a switch statement. This keeps
header construction in one place and makes the EMSGSIZE bail-out uniform.
Add a new request flag attribute, NL80211_ATTR_STA_DUMP_LINK_STATS
(NLA_FLAG), for NL80211_CMD_GET_STATION dump. Userspace can set this
flag to request per-link station statistics for MLO stations.
Extract this flag during the first dump invocation by passing an attrbuf
to nl80211_prepare_wdev_dump(); use __free(kfree) to avoid scattered
manual kfree() calls. Cache the boolean in the dump context to avoid
repeated parsing on subsequent invocations.
Per-link messages carry a single NL80211_ATTR_MLO_LINKS nest with the
link ID, link-specific MAC, and per-link NL80211_ATTR_STA_INFO payload.
The link-specific validity (is_valid_ether_addr) and null pointer guard
are checked in nl80211_put_link_station_payload() before any message
construction begins.
Also fix all nla_nest_start_noflag() calls in nl80211_fill_link_station()
for nested attribute types (STA_INFO, BSS_PARAM, TID_STATS, per-tid) to
use nla_nest_start() so the NLA_F_NESTED flag is set correctly.
Propagate the actual return value from nl80211_put_sta_info_common() in
the AGGREGATED phase rather than returning skb->len. Returning skb->len
signals netlink to re-invoke the dump with the same sta_idx, causing an
infinite loop when the aggregated payload is too large to fit; returning
the real error code (-EMSGSIZE or otherwise) terminates the dump cleanly.
Backward compatibility is seamlessly preserved for non-MLO stations.
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260614051739.3979947-5-praneesh.p@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, nl80211_dump_station() relies on the netlink callback's generic
args array (cb->args[2]) to track the station index during dumps. It also
processes the entire sinfo structure and transmits it to userspace
immediately in a single pass.
This approach creates a bottleneck for MLO. When an MLD station has
multiple active links, the aggregated station information, combined
with the individual per-link statistics, can easily exceed the
maximum netlink message size limits. The current monolithic dump
iteration cannot pause and resume mid-station to fragment these large
per-link statistics across multiple netlink messages.
Introduce a stateful context structure (struct nl80211_dump_station_ctx)
allocated during the dump to track the iteration state. Store the context
pointer directly at cb->args[2], following the same pattern as
nl80211_dump_wiphy which stores its state pointer at cb->args[0].
Move the station index (sta_idx) tracking and the sinfo payload into this
context. The per-station netlink message is built inline in the loop:
common header attributes are assembled directly, then
nl80211_put_sta_info_common() adds the STA_INFO payload.
Furthermore, move the NL80211_CMD_GET_STATION command definition from
genl_small_ops to genl_ops to natively support the .done callback.
Implement nl80211_dump_station_done() to ensure the newly allocated state
context and its deeply allocated sinfo payload are safely freed when the
dump concludes or is aborted prematurely by userspace.
Note that the previous dump path used nl80211_send_station(), which
included NL80211_ATTR_IE and NL80211_ATTR_RESP_IE. These attributes are
not carried forward in this implementation. As documented, association
response IEs (assoc_resp_ies) are only relevant at station creation time
(e.g. via cfg80211_new_sta()) to notify userspace about association
details, and are not expected to be part of get_station()/dump_station()
callbacks. Aligning with this expectation, these IEs are intentionally
omitted here.
This refactoring maintains the existing netlink batching performance while
laying the stateful foundation required for per-link statistics
fragmentation in subsequent patches.
At out_err_release, cfg80211_sinfo_release_content() frees any
dynamically allocated sub-fields inside ctx->sinfo (including per-link
pointers in sinfo.links[]). Without the subsequent memset, those
pointers remain non-NULL in the embedded sinfo. When the dump concludes
or is aborted, nl80211_dump_station_done() calls
cfg80211_sinfo_release_content() a second time on the same ctx->sinfo,
which would free the already-released link memory. The
memset(&ctx->sinfo, 0, sizeof(ctx->sinfo)) zeroes all pointers so the
second release call hits kfree(NULL), which is a harmless no-op.
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260614051739.3979947-4-praneesh.p@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a helper function nl80211_put_sta_info_common() to pack the
station-level (aggregated) STA information into a netlink message.
This prepares the code for future enhancements such as supporting
fragmented link statistics in nl80211_dump_station.
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260614051739.3979947-3-praneesh.p@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove the link level statistics handling from
nl80211_send_station() and drop the unused link_stats parameter
from its signature and callers. The removed code iterated over
each MLO link and attempted to send link specific station data
through NL80211_ATTR_MLO_LINKS, but this logic was never used
because link_stats was always false.
This logic was introduced during early work on link level station
statistics with the intention of reporting information for each
link. Due to message size concerns when a station has multiple
links, the feature was disabled behind the link_stats flag and
remained unused.
The link level reporting block in nl80211_send_station() is dead
code and cannot support larger messages, so remove it. This
cleanup also prepares for proper link level statistics reporting
in nl80211_dump_station() in a later patch, where fragmentation
allows safe transmission of multi link data.
Also fix label indentation: the nla_put_failure label had an
erroneous leading space.
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260614051739.3979947-2-praneesh.p@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 6c3ea155e5ee ("Bluetooth: L2CAP: Fix not tracking outstanding
TX ident") changed ident allocation to use an IDA, releasing idents in
l2cap_put_ident() when the matching response command is received.
But identifiers allocated for commands that have no response defined
are never released. In particular L2CAP_LE_CREDITS is sent repeatedly for
the lifetime of an LE CoC channel, so a peer streaming data to the
host exhausts the 1-255 ident range after 254 credit packets. From
then on l2cap_get_ident() fails:
kernel: Bluetooth: Unable to allocate ident: -28
and every subsequent L2CAP_LE_CREDITS packet is sent with ident 0,
which is invalid (Core Spec, Vol 3, Part A, Section 4: "Signaling
identifier 0x00 is an invalid identifier and shall never be used in
any command"). Remote stacks that validate the ident drop these
commands, never receive new credits, and the channel stalls
permanently. With default socket buffers this happens after roughly 0.5 MB
of received data (the exact amount depends on the socket receive buffer):
< ACL Data TX: Handle 2048 flags 0x00 dlen 12
LE L2CAP: LE Flow Control Credit (0x16) ident 0 len 4
Source CID: 64
Credits: 1
Release the ident immediately after sending L2CAP_LE_CREDITS since no
response will ever release it. Use a local variable instead of
chan->ident so that an ident that an EXT_FLOWCTL channel may be waiting on
(e.g. a pending reconfigure) is not overwritten by a credit packet.
Also add the missing L2CAP_LE_CONN_RSP case to l2cap_put_ident() so
idents allocated for outgoing L2CAP_LE_CONN_REQ commands are released
when the response arrives.
Fixes: 6c3ea155e5ee ("Bluetooth: L2CAP: Fix not tracking outstanding TX ident")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221629
Assisted-by: Claude:claude-opus-4.8
Assisted-by: Fable:5
Signed-off-by: Stig Hornang <stig@hornang.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Core specification (Part C vol 4 sec 5.4.5) does not exclude empty
ISO_CONT, ISO_END packets. We currently reject them if they are last.
If controller sends malformed sequence
ISO_START -> rx_len = 4, ISO_CONT skb->len 4, ISO_START
that ends payload in ISO_CONT, we leak conn->rx_skb. If controller sends
too long ISO_END, we panic on skb_put. If controller sends too short
ISO_END we accept it.
Fix by marking unfinished ISO_START via conn->rx_skb != NULL. Check
skb->len properly before skb_put. Combine the ISO_CONT/END code paths
as they require the same initial checks. Reject too short ISO_END
packets.
Fixes: 84c24fb151fc ("Bluetooth: ISO: drop ISO_END frames received without prior ISO_START")
Fixes: ccf74f2390d6 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
l2cap_sock_new_connection_cb() returned l2cap_pi(sk)->chan after
release_sock(parent). Once the parent lock is dropped the newly
enqueued child socket sk is reachable via the accept queue, so another
task can accept and free it before the callback dereferences sk,
resulting in a use-after-free.
Rework the ->new_connection() op so the core, rather than the callback,
owns the child channel's lifetime. The op now receives a pre-allocated
new_chan and returns an errno instead of allocating and returning a
channel. l2cap_new_connection() allocates the child channel and links
it into the conn list via __l2cap_chan_add() before invoking the
callback, so the conn-list reference keeps the channel alive once
release_sock(parent) exposes the socket to other tasks.
Channel configuration that was duplicated in l2cap_sock_init() and the
various new_connection callbacks is consolidated into
l2cap_chan_set_defaults(), which now inherits from the parent channel
when one is supplied.
Fixes: 8ffb929098a5 ("Bluetooth: Remove parent socket usage from l2cap_core.c")
Cc: stable@kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Siwei Zhang <oss@fourdim.xyz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
bt_accept_get() takes a temporary reference before dropping the accept
queue lock. bt_accept_dequeue() currently drops that reference before
bt_accept_unlink(), leaving only the queue reference.
bt_accept_unlink() drops the queue reference. The subsequent
sock_hold() therefore accesses freed memory if it was the final
reference, as observed by KASAN during listening L2CAP socket cleanup.
Retain the temporary queue-walk reference through unlink and hand it to
the caller on success. Drop it explicitly on the closed and
not-yet-connected paths.
Fixes: ab1513597c6c ("Bluetooth: fix UAF in l2cap_sock_cleanup_listen() vs l2cap_conn_del()")
Reported-by: syzbot+674ff7e4d7fdfd572afc@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=674ff7e4d7fdfd572afc
Cc: stable@vger.kernel.org
Signed-off-by: Yousef Alhouseen <alhouseenyousef@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
bnep_add_connection() reads the L2CAP connection without holding the
channel lock, then passes its HCI device to register_netdev(). Controller
teardown can clear and release that connection concurrently, leaving the
network device registration path to dereference a freed parent device.
Take a reference to the L2CAP connection while holding the channel lock.
Retain it until register_netdev() has taken the parent device reference.
Fixes: 65f53e9802db ("Bluetooth: Access BNEP session addresses through L2CAP channel")
Reported-by: syzbot+fed5dce4553262f3b35c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=fed5dce4553262f3b35c
Cc: stable@vger.kernel.org
Signed-off-by: Yousef Alhouseen <alhouseenyousef@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
sco_sock_timeout() runs asynchronously and lock_sock(sk). If the socket
is closing while the timer is running, it holds the same lock
(lock_sock(sk)) twice, leading to a deadlock.
CPU 0 CPU 1
==================== ======================
sco_sock_close()
sco_sock_timeout()
lock_sock(sk) // <-- LOCK
__sco_sock_close()
sco_chan_del()
sco_conn_put()
sco_conn_free()
disable_delayed_work_sync()
lock(sk) // <-- SAME LOCK
Fix this by moving disable_delayed_work_sync() outside of lock_sock(sk),
ensuring that no lock_sock(sk) is held before sco_sock_timeout().
Lockdep splat:
WARNING: possible circular locking dependency detected
6.13.0-rc4 #7 Not tainted
syz-executor292/9514 is trying to acquire lock:
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: rcu_lock_acquire sect/v6.13-rc4/./include/linux/rcupdate.h:337 [inline]
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: rcu_read_lock sect/v6.13-rc4/./include/linux/rcupdate.h:849 [inline]
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: start_flush_work sect/v6.13-rc4/kernel/workqueue.c:4137 [inline]
ffff8881115d5070 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}, at: __flush_work+0xd1/0xc40 sect/v6.13-rc4/kernel/workqueue.c:4195
but task is already holding lock:
ffff88807db3a258 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at: lock_sock sect/v6.13-rc4/./include/net/sock.h:1623 [inline]
ffff88807db3a258 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at: sco_sock_close+0x25/0x100 sect/v6.13-rc4/net/bluetooth/sco.c:524
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
lock_acquire+0x1c4/0x520 sect/v6.13-rc4/kernel/locking/lockdep.c:5849
lock_sock_nested+0x48/0x130 sect/v6.13-rc4/net/core/sock.c:3622
lock_sock sect/v6.13-rc4/./include/net/sock.h:1623 [inline]
sco_sock_timeout+0xbe/0x270 sect/v6.13-rc4/net/bluetooth/sco.c:158
process_one_work sect/v6.13-rc4/kernel/workqueue.c:3229 [inline]
process_scheduled_works+0xa99/0x18f0 sect/v6.13-rc4/kernel/workqueue.c:3310
worker_thread+0x8a9/0xd80 sect/v6.13-rc4/kernel/workqueue.c:3391
kthread+0x2c6/0x360 sect/v6.13-rc4/kernel/kthread.c:389
ret_from_fork+0x4e/0x80 sect/v6.13-rc4/arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 sect/v6.13-rc4/arch/x86/entry/entry_64.S:244
-> #0 ((work_completion)(&(&conn->timeout_work)->work)){+.+.}-{0:0}:
check_prev_add sect/v6.13-rc4/kernel/locking/lockdep.c:3161 [inline]
check_prevs_add sect/v6.13-rc4/kernel/locking/lockdep.c:3280 [inline]
validate_chain+0x1888/0x5760 sect/v6.13-rc4/kernel/locking/lockdep.c:3904
__lock_acquire+0x13b4/0x2120 sect/v6.13-rc4/kernel/locking/lockdep.c:5226
lock_acquire+0x1c4/0x520 sect/v6.13-rc4/kernel/locking/lockdep.c:5849
touch_work_lockdep_map sect/v6.13-rc4/kernel/workqueue.c:3909 [inline]
start_flush_work sect/v6.13-rc4/kernel/workqueue.c:4163 [inline]
__flush_work+0x70f/0xc40 sect/v6.13-rc4/kernel/workqueue.c:4195
__cancel_work_sync sect/v6.13-rc4/kernel/workqueue.c:4351 [inline]
disable_delayed_work_sync+0xbb/0xf0 sect/v6.13-rc4/kernel/workqueue.c:4514
sco_conn_free sect/v6.13-rc4/net/bluetooth/sco.c:95 [inline]
kref_put sect/v6.13-rc4/./include/linux/kref.h:65 [inline]
sco_conn_put+0x18f/0x270 sect/v6.13-rc4/net/bluetooth/sco.c:107
sco_chan_del+0xe2/0x210 sect/v6.13-rc4/net/bluetooth/sco.c:236
sco_sock_close+0x8f/0x100 sect/v6.13-rc4/net/bluetooth/sco.c:526
sco_sock_release+0x62/0x2d0 sect/v6.13-rc4/net/bluetooth/sco.c:1300
__sock_release+0xe1/0x2d0 sect/v6.13-rc4/net/socket.c:640
sock_close+0x1c/0x30 sect/v6.13-rc4/net/socket.c:1408
__fput+0x2bd/0xa80 sect/v6.13-rc4/fs/file_table.c:450
__fput_sync+0x15e/0x1c0 sect/v6.13-rc4/fs/file_table.c:535
__do_sys_close sect/v6.13-rc4/fs/open.c:1554 [inline]
__se_sys_close sect/v6.13-rc4/fs/open.c:1539 [inline]
__x64_sys_close+0x93/0x120 sect/v6.13-rc4/fs/open.c:1539
do_syscall_x64 sect/v6.13-rc4/arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xee/0x210 sect/v6.13-rc4/arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: e6720779ae61 ("Bluetooth: SCO: Use kref to track lifetime of sco_conn")
Acked-by: Dave Tian <daveti@purdue.edu>
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_add_adv_monitor() publishes a new adv_monitor in
hdev->adv_monitors_idr before the powered MSFT setup step. The MSFT
offload add path can then fail either locally before the controller add
command completes, or in the MSFT add callback. In the current queued
management add flow, hci_cmd_sync_work() still invokes
mgmt_add_adv_patterns_monitor_complete() with the original pending command
after msft_add_monitor_pattern() returns.
The buggy scenario involves two paths, with each column showing the order
within that path:
MSFT add handling MGMT completion
1. insert monitor and handle 1. receive sync error
2. send MSFT add command 2. call add-monitor completion
3. callback sees bad response 3. load cmd->user_data
4. callback frees monitor 4. read monitor->handle
Local MSFT setup failures have the other half of the same ownership bug:
they return an error after the IDR insertion, but no later code removes the
failed monitor from the IDR.
Keep ownership with the pending management command until its completion.
For normal management adds, the MSFT add callback now records successful
controller state and returns errors to its caller. The management
completion frees the monitor on non-success after copying the response
handle, while resume/reregister callback-error cleanup remains in the
MSFT callback. The success path keeps the existing bookkeeping.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x5f0
? mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x19f/0x330
? mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
kasan_report+0xe0/0x110
? mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
mgmt_add_adv_patterns_monitor_complete+0xfb/0x260 [bluetooth]
? srso_alias_return_thunk+0x5/0xfbef5
? 0xffffffffc00d00da
? __pfx_mgmt_add_adv_patterns_monitor_complete+0x10/0x10 [bluetooth]
? __pfx_mgmt_add_adv_patterns_monitor_complete+0x10/0x10 [bluetooth]
? hci_cmd_sync_work+0x1ab/0x210 [bluetooth]
hci_cmd_sync_work+0x1c0/0x210 [bluetooth]
? __pfx_mgmt_add_adv_patterns_monitor_complete+0x10/0x10 [bluetooth]
process_one_work+0x4fd/0xbc0
? __pfx_process_one_work+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? __list_add_valid_or_report+0x37/0xf0
? __pfx_hci_cmd_sync_work+0x10/0x10 [bluetooth]
? srso_alias_return_thunk+0x5/0xfbef5
worker_thread+0x2d8/0x570
? __pfx_worker_thread+0x10/0x10
kthread+0x1ad/0x1f0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c9/0x540
? __pfx_ret_from_fork+0x10/0x10
? srso_alias_return_thunk+0x5/0xfbef5
? __switch_to+0x2e9/0x730
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 471 on cpu 3 at 285.205389s:
kasan_save_stack+0x33/0x60
kasan_save_track+0x17/0x60
__kasan_kmalloc+0xaa/0xb0
add_adv_patterns_monitor_rssi+0xd5/0x230 [bluetooth]
hci_sock_sendmsg+0x96b/0xf80 [bluetooth]
__sys_sendto+0x2bc/0x2d0
__x64_sys_sendto+0x76/0x90
do_syscall_64+0x115/0x6a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 454 on cpu 2 at 285.217112s:
kasan_save_stack+0x33/0x60
kasan_save_track+0x17/0x60
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x5f/0x80
kfree+0x313/0x590
msft_add_monitor_sync+0x54a/0x570 [bluetooth]
hci_add_adv_monitor+0x133/0x180 [bluetooth]
hci_cmd_sync_work+0x187/0x210 [bluetooth]
process_one_work+0x4fd/0xbc0
worker_thread+0x2d8/0x570
kthread+0x1ad/0x1f0
ret_from_fork+0x3c9/0x540
ret_from_fork_asm+0x1a/0x30
Fixes: a2a4dedf88ab ("Bluetooth: advmon offload MSFT add monitor")
Assisted-by: Codex:gpt-5.5
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
get_l2cap_conn() looks up an LE hci_conn under hdev protection, but
then drops that protection before reading hcon->l2cap_data and before
lowpan_control_write() later dereferences conn->hcon. A disconnect or
device close can tear down the same L2CAP connection in that window.
The buggy scenario involves two paths, with each column showing the order
within that path:
6LoWPAN control write: HCI disconnect/device close:
1. get_l2cap_conn() finds hcon 1. hci_disconn_cfm() dispatches
and hcon->l2cap_data. the L2CAP disconnect callback.
2. get_l2cap_conn() drops hdev 2. l2cap_conn_del() clears
protection and returns conn. hcon->l2cap_data and drops the
L2CAP connection reference.
3. lowpan_control_write() reads 3. hci_conn_del() removes and drops
conn->hcon. the HCI connection.
Take a reference to the L2CAP connection with
l2cap_conn_hold_unless_zero() while hdev is still locked, and drop that
reference after the debugfs command's last use of conn. This mirrors the
existing L2CAP ACL receive-side handoff and keeps the connection
dereferenceable after leaving hdev protection. Export the existing helper
so the bluetooth_6lowpan module can use the same lifetime primitive.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in lowpan_control_write+0x374/0x520
The buggy address belongs to the object at ffff888111b9d000 which belongs
to the cache kmalloc-1k of size 1024
The buggy address is located 0 bytes inside of freed 1024-byte region
[ffff888111b9d000, ffff888111b9d400)
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0
print_report+0xce/0x5f0
lowpan_control_write+0x374/0x520 (net/bluetooth/6lowpan.c:1131)
srso_alias_return_thunk+0x5/0xfbef5
__virt_addr_valid+0x19f/0x330
kasan_report+0xe0/0x110
__debugfs_file_get+0xf7/0x400
full_proxy_write+0x9e/0xd0
vfs_write+0x1b0/0x810
ksys_write+0xd2/0x170
dnotify_flush+0x32/0x220
do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Allocated by task stack:
kasan_save_stack+0x33/0x60
kasan_save_track+0x17/0x60
__kasan_kmalloc+0xaa/0xb0
l2cap_conn_add+0x45/0x520
l2cap_chan_connect+0xac6/0xd90
l2cap_sock_connect+0x216/0x350
__sys_connect+0x101/0x130
__x64_sys_connect+0x40/0x50
do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task stack:
kasan_save_stack+0x33/0x60
kasan_save_track+0x17/0x60
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x5f/0x80
kfree+0x313/0x590
hci_conn_hash_flush+0xc0/0x140
hci_dev_close_sync+0x41a/0xb00
hci_dev_close+0x12f/0x160
hci_sock_ioctl+0x157/0x570
sock_do_ioctl+0xf7/0x210
sock_ioctl+0x32f/0x490
__x64_sys_ioctl+0xc7/0x110
do_syscall_64+0x115/0x6a0 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f
kasan_record_aux_stack+0xa7/0xc0
insert_work+0x32/0x100
__queue_work+0x262/0xa60
queue_work_on+0xad/0xb0
l2cap_connect_cfm+0x4ef/0x670
hci_le_remote_feat_complete_evt+0x247/0x430
hci_event_packet+0x360/0x6f0
hci_rx_work+0x2ae/0x7a0
process_one_work+0x4fd/0xbc0
worker_thread+0x2d8/0x570
kthread+0x1ad/0x1f0
ret_from_fork+0x3c9/0x540
ret_from_fork_asm+0x1a/0x30
Fixes: 6b8d4a6a0314 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Assisted-by: Codex:gpt-5.5
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
lowpan_enable_set() allocates a temporary work item and schedules
do_enable_set() on system_wq, then returns to debugfs. The debugfs active
operation has ended at that point, but the worker still executes module
text and manipulates enable_6lowpan and listen_chan.
bt_6lowpan_exit() removes the debugfs files and immediately closes and
puts listen_chan. It has no pointer to the queued work item, so it cannot
cancel or flush it before tearing down the state that the worker uses.
The buggy scenario involves two paths, with each column showing the order
within that path:
debugfs enable write module exit
1. lowpan_enable_set() allocates 1. bt_6lowpan_exit() removes
set_enable work the debugfs file
2. schedule_work() queues 2. bt_6lowpan_exit() closes
do_enable_set() and puts listen_chan
3. the write operation returns 3. module teardown can continue
4. do_enable_set() later runs
against stale state
Run the enable state transition synchronously in lowpan_enable_set()
instead. The simple debugfs setter can sleep, and this file already handles
the 6LoWPAN control write synchronously under the same set_lock. Once the
setter returns, debugfs removal covers the whole operation and exit can no
longer race with an untracked work item.
Validation reproduced this kernel report:
BUG: KASAN: slab-use-after-free in do_enable_set+0x113/0x2e0
Workqueue: events do_enable_set [bluetooth_6lowpan]
The buggy address belongs to the object at ffff888109cb8000
Fixes: 90305829635d ("Bluetooth: 6lowpan: Converting rwlocks to use RCU")
Assisted-by: Codex:gpt-5.5
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_abort_conn() read hci_skb_event(hdev->sent_cmd) when a connection
was pending, but hdev->sent_cmd can be NULL while req_status is still
HCI_REQ_PEND, leading to a NULL pointer dereference and a general
protection fault from the hci_rx_work() receive path.
Instead of inspecting hdev->sent_cmd, track the in-flight create
connection command with a new per-connection HCI_CONN_CREATE flag and
route all cancellation through hci_cancel_connect_sync(), which
dispatches to a dedicated per-type cancel function. The create command
is in exactly one of two states: still queued, or in flight. The cancel
function holds cmd_sync_work_lock across the whole decision: the worker
takes this lock to dequeue every entry, so while it is held a queued
command cannot start running and an in-flight command cannot complete
and let the next command become pending. This keeps the flag test and
hci_cmd_sync_cancel() atomic with respect to the worker, so a queued
command is simply dequeued, and an in-flight command owned by this
connection is cancelled without the risk of cancelling an unrelated
command that became pending in the meantime. CIS uses the same flag
mechanism via HCI_CONN_CREATE_CIS but cannot be dequeued per-connection.
hci_acl_create_conn_sync() and hci_le_create_conn_sync() clear
HCI_CONN_CREATE after the create command completes, but the command
status handler can free conn via hci_conn_del() (for example when the
controller rejects the connection) while the worker is still blocked on
the connection complete event. Hold a reference on conn across the
create command so the flag can be cleared without a use-after-free.
Fixes: a13f316e90fd ("Bluetooth: hci_conn: Consolidate code for aborting connections")
Cc: stable@vger.kernel.org
Suggested-by: XIAO WU <xiaowu.417@qq.com>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Siwei Zhang <oss@fourdim.xyz>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
l2cap_get_conf_opt() derives the option length from the
attacker-controlled opt->len field and immediately dereferences
opt->val (as u8, get_unaligned_le16() or get_unaligned_le32(), or a
raw pointer for the default case) before any caller has confirmed
that opt->len bytes are present in the buffer. The callers
(l2cap_parse_conf_req(), l2cap_parse_conf_rsp() and
l2cap_conf_rfc_get()) only detect a malformed option afterwards, once
the running length has gone negative, by which point the
out-of-bounds read has already executed.
An existing post-hoc length check keeps the garbage value from being
consumed, so this is not a data leak in the current control flow. It
is still a validate-after-use ordering bug: up to 4 bytes are read
past the end of the buffer before it is known to contain them, and it
is fragile to future changes in the callers.
Fix it at the source. Pass the end of the buffer into
l2cap_get_conf_opt() and refuse to touch opt->val unless the full
option (header + value) fits. Each caller computes an end pointer
once before the loop and checks the return value directly instead of
inferring the error from a negative length.
Fixes: 7c9cbd0b5e38 ("Bluetooth: Verify that l2cap_get_conf_opt provides large enough buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
l2cap_conn_del() takes conn->lock and then calls cancel_work_sync() for
pending_rx_work. process_pending_rx() takes the same mutex, so teardown
can deadlock against the worker it is flushing.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the l2cap_conn_ready() -> queue_work(...,
&conn->pending_rx_work) submit path, the l2cap_conn_del() ->
cancel_work_sync(&conn->pending_rx_work) teardown path, and the
process_pending_rx() -> mutex_lock(&conn->lock) worker edge. Lockdep
reported:
WARNING: possible circular locking dependency detected
process_pending_rx+0x21/0x2a [vuln_msv]
l2cap_conn_del.constprop.0+0x3f/0x4e [vuln_msv]
*** DEADLOCK ***
Cancel pending_rx_work before taking conn->lock, matching the existing
lock-before-drain ordering used for the two delayed works in the same
teardown path. The pending_rx queue is still purged after the work has
been cancelled and conn->lock has been acquired.
Fixes: 7ab56c3a6ecc ("Bluetooth: Fix deadlock in l2cap_conn_del()")
Cc: stable@vger.kernel.org
Signed-off-by: Runyu Xiao <runyu.xiao@seu.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
iso_conn_big_sync() drops the socket lock to call hci_get_route() and
then re-acquires it, but dereferences iso_pi(sk)->conn->hcon afterwards
without re-checking that conn is still valid.
While the lock is dropped, the connection can be torn down under the
same socket lock: iso_disconn_cfm() -> iso_conn_del() -> iso_chan_del()
sets iso_pi(sk)->conn to NULL (and the broadcast teardown path can also
clear conn->hcon on its own). When iso_conn_big_sync() re-acquires the
lock and reads conn->hcon, conn may be NULL, causing a NULL pointer
dereference (hcon is the first member of struct iso_conn).
This path is reached from iso_sock_recvmsg() for a PA-sync broadcast
sink socket (BT_SK_DEFER_SETUP | BT_SK_PA_SYNC), so the dropped-lock
window can race with connection teardown driven by controller events.
Re-validate iso_pi(sk)->conn and its hcon after re-acquiring the socket
lock and bail out if the connection went away, as already done in the
sibling iso_sock_rebind_bc().
Fixes: 7a17308c17880d ("Bluetooth: iso: Fix circular lock in iso_conn_big_sync")
Cc: stable@vger.kernel.org
Signed-off-by: Muhammad Bilal <meatuni001@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
add_device_complete() runs from the hci_cmd_sync_work kworker, which
holds only hci_req_sync_lock and *not* hci_dev_lock. It calls
hci_conn_params_lookup() and then dereferences the returned object
(params->flags) without taking hci_dev_lock:
params = hci_conn_params_lookup(hdev, &cp->addr.bdaddr,
le_addr_type(cp->addr.type));
...
device_flags_changed(NULL, hdev, &cp->addr.bdaddr,
cp->addr.type, hdev->conn_flags,
params ? params->flags : 0);
hci_conn_params_lookup() walks hdev->le_conn_params and is documented to
require hdev->lock. A concurrent MGMT_OP_REMOVE_DEVICE
(remove_device()), which does run under hci_dev_lock, can call
hci_conn_params_free() to list_del() and kfree() the very object the
lookup returned, so the subsequent params->flags read touches freed
memory [0].
Hold hci_dev_lock() across the hci_conn_params_lookup() and the read of
params->flags (and the matching event emission) so the lookup result
cannot be freed by a concurrent remove_device() before it is used,
honouring the locking contract of hci_conn_params_lookup().
[0]: (trailing page/memory-state dump trimmed)
BUG: KASAN: slab-use-after-free in add_device_complete+0x358/0x3d8 net/bluetooth/mgmt.c:7671
Read of size 1 at addr ffff000017ab26c1 by task kworker/u9:8/388
CPU: 1 UID: 0 PID: 388 Comm: kworker/u9:8 Not tainted 7.0.11 #20 PREEMPT
Hardware name: linux,dummy-virt (DT)
Workqueue: hci0 hci_cmd_sync_work
Call trace:
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:499 (C)
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xb4/0xd4 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x118/0x5d8 mm/kasan/report.c:482
kasan_report+0xb0/0xf4 mm/kasan/report.c:595
__asan_report_load1_noabort+0x20/0x2c mm/kasan/report_generic.c:378
add_device_complete+0x358/0x3d8 net/bluetooth/mgmt.c:7671
hci_cmd_sync_work+0x14c/0x240 net/bluetooth/hci_sync.c:334
process_one_work+0x628/0xd38 kernel/workqueue.c:3289
process_scheduled_works kernel/workqueue.c:3372 [inline]
worker_thread+0x7a8/0xac0 kernel/workqueue.c:3453
kthread+0x39c/0x444 kernel/kthread.c:436
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860
Allocated by task 3401:
kasan_save_stack+0x3c/0x64 mm/kasan/common.c:57
kasan_save_track+0x20/0x3c mm/kasan/common.c:78
kasan_save_alloc_info+0x40/0x54 mm/kasan/generic.c:570
poison_kmalloc_redzone mm/kasan/common.c:398 [inline]
__kasan_kmalloc+0xd4/0xd8 mm/kasan/common.c:415
kasan_kmalloc include/linux/kasan.h:263 [inline]
__kmalloc_cache_noprof+0x1b0/0x458 mm/slub.c:5385
kmalloc_noprof include/linux/slab.h:950 [inline]
kzalloc_noprof include/linux/slab.h:1188 [inline]
hci_conn_params_add+0x10c/0x4b0 net/bluetooth/hci_core.c:2279
hci_conn_params_set net/bluetooth/mgmt.c:5162 [inline]
add_device+0x5b4/0xa54 net/bluetooth/mgmt.c:7755
hci_mgmt_cmd net/bluetooth/hci_sock.c:1721 [inline]
hci_sock_sendmsg+0x10b4/0x1dd0 net/bluetooth/hci_sock.c:1841
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0xe0/0x128 net/socket.c:742
sock_write_iter+0x250/0x390 net/socket.c:1195
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x66c/0xab0 fs/read_write.c:688
ksys_write+0x1fc/0x24c fs/read_write.c:740
__do_sys_write fs/read_write.c:751 [inline]
__se_sys_write fs/read_write.c:748 [inline]
__arm64_sys_write+0x70/0xa4 fs/read_write.c:748
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x84/0x2a8 arch/arm64/kernel/syscall.c:49
el0_svc_common.constprop.0+0xe4/0x294 arch/arm64/kernel/syscall.c:132
do_el0_svc+0x44/0x5c arch/arm64/kernel/syscall.c:151
el0_svc+0x38/0xac arch/arm64/kernel/entry-common.c:724
el0t_64_sync_handler+0xa0/0xe4 arch/arm64/kernel/entry-common.c:743
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:596
Freed by task 3740:
kasan_save_stack+0x3c/0x64 mm/kasan/common.c:57
kasan_save_track+0x20/0x3c mm/kasan/common.c:78
kasan_save_free_info+0x4c/0x74 mm/kasan/generic.c:584
poison_slab_object mm/kasan/common.c:253 [inline]
__kasan_slab_free+0x88/0xb8 mm/kasan/common.c:285
kasan_slab_free include/linux/kasan.h:235 [inline]
slab_free_hook mm/slub.c:2685 [inline]
slab_free mm/slub.c:6170 [inline]
kfree+0x14c/0x458 mm/slub.c:6488
hci_conn_params_free+0x288/0x484 net/bluetooth/hci_core.c:2312
remove_device+0x4b0/0x968 net/bluetooth/mgmt.c:7919
hci_mgmt_cmd net/bluetooth/hci_sock.c:1721 [inline]
hci_sock_sendmsg+0x10b4/0x1dd0 net/bluetooth/hci_sock.c:1841
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0xe0/0x128 net/socket.c:742
sock_write_iter+0x250/0x390 net/socket.c:1195
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x66c/0xab0 fs/read_write.c:688
ksys_write+0x1fc/0x24c fs/read_write.c:740
__do_sys_write fs/read_write.c:751 [inline]
__se_sys_write fs/read_write.c:748 [inline]
__arm64_sys_write+0x70/0xa4 fs/read_write.c:748
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x84/0x2a8 arch/arm64/kernel/syscall.c:49
el0_svc_common.constprop.0+0xe4/0x294 arch/arm64/kernel/syscall.c:132
do_el0_svc+0x44/0x5c arch/arm64/kernel/syscall.c:151
el0_svc+0x38/0xac arch/arm64/kernel/entry-common.c:724
el0t_64_sync_handler+0xa0/0xe4 arch/arm64/kernel/entry-common.c:743
el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:596
Fixes: 1e2e3044c1bc ("Bluetooth: MGMT: Fix MGMT_OP_ADD_DEVICE invalid device flags")
Cc: stable@vger.kernel.org
Assisted-by: Bynario AI
Signed-off-by: Samuel Page <sam@bynar.io>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
b66774b48dd9 ("Bluetooth: L2CAP: Fix UAF in channel timeout by holding
conn ref") don't reset the chan->conn to NULL anymore making the bt#
netdev not be remove once the last l2cap_chan_del is removed.
Instead of restoring the original behavior this remove the logic of
keeping the interface after the last channel is removed because it
never worked as intended and the l2cap_chan_del always detach its
l2cap_conn which results in always removing the channel anyway.
Fixes: b66774b48dd9 ("Bluetooth: L2CAP: Fix UAF in channel timeout by holding conn ref")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
ieee80211_rx_mgmt_deauth() reads the deauth reason code before checking
that the fixed field is actually present in the received frame.
Validate the deauth frame length first and only then read the reason
code.
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612185042.66260-6-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When assoc_data->s1g is set and no AID Response element is present,
falling back to mgmt->u.assoc_resp.aid reads the non-S1G
association-response layout.
Keep the fallback for non-S1G only. If a successful S1G association
response omits the AID Response element, abandon the association
instead of proceeding with AID 0. Initialize aid to 0 for other S1G
responses so the later mask and logging flow keeps a defined value
without reading the non-S1G layout.
Fixes: 2a8a6b7c4cb0 ("wifi: mac80211: handle station association response with S1G")
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612152440.25955-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A PMSR request with an empty peers array is not a useful request and
weakens the cfg80211-to-driver contract by allowing start_pmsr() with
no target peer.
Reject empty peer lists before allocating the request object or calling
into the driver.
Fixes: 9bb7e0f24e7e7 ("cfg80211: add peer measurement with FTM initiator API")
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612133717.93783-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
PMSR FTM location request flags are syntactically valid, but they must
be rejected when the device capability does not advertise support for
them.
Return an error immediately after rejecting unsupported LCI or civic
location request bits so the request cannot reach the driver.
Fixes: 9bb7e0f24e7e7 ("cfg80211: add peer measurement with FTM initiator API")
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612133710.93544-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
PMSR FTM request parsing accepts preamble values outside the
enumerated nl80211 preamble range.
Reject out-of-range values before using them in the parser capability
bit test using the policy.
Fixes: 9bb7e0f24e7e7 ("cfg80211: add peer measurement with FTM initiator API")
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612133703.93274-2-enderaoelyther@gmail.com
[drop unnecessary check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
PMSR request parsing accepts missing or duplicated measurement type
entries in NL80211_PMSR_REQ_ATTR_DATA.
Track whether one measurement type was already provided, reject a
second one immediately, and return an error if the request data block
contains no measurement type at all.
Fixes: 9bb7e0f24e7e7 ("cfg80211: add peer measurement with FTM initiator API")
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612133656.92900-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
