| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
hci_setup_ext_adv_instance_sync(...) only disabled
HCI_OP_LE_SET_EXT_ADV_ENABLE before setup snapshot in case of non-legacy
instances (instance > 0) and never disabled the same for legacy instance
(instance == 0). This would lead to failure in setting ext adv params
with HCI_ERROR_COMMAND_DISALLOWED (0x0c) error like below, when toggling
the discoverable/connectable property of a controller with advertising
enabled.
```
$ btmgmt advertising off
hci0 Set Advertising complete, settings: powered ssp br/edr le
secure-conn wide-band-speech cis-central cis-peripheral
$ btmgmt connectable on
hci0 Set Connectable complete, settings: powered connectable ssp br/edr
le secure-conn wide-band-speech cis-central cis-peripheral
$ btmgmt connectable off
hci0 Set Connectable complete, settings: powered ssp br/edr le
secure-conn wide-band-speech cis-central cis-peripheral
$ btmgmt advertising on
hci0 Set Advertising complete, settings: powered connectable ssp br/edr
le advertising secure-conn wide-band-speech cis-central cis-peripheral
$ btmgmt connectable on
Set Connectable for hci0 failed with status 0x0a (Busy)
$ btmgmt connectable off
Set Connectable for hci0 failed with status 0x0a (Busy)
$ dmesg
...
[ 21.970527] hci0: Opcode 0x2036
[ 21.970529] hci0: opcode 0x2036 plen 25
[ 21.970537] hci0: skb len 28
[ 21.970539] hci0: length 1
[ 21.976099] hci0: result 0x0c
[ 21.976105] hci0: end: err -16
[ 21.976114] Bluetooth: hci0: Opcode 0x2036 failed: -16
```
Signed-off-by: Muhammad Saheed <muhammad.saheed.iam@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_le_per_adv_report_evt() is dispatched with a minimum length of
sizeof(struct hci_ev_le_per_adv_report), which only covers the fixed
part of the event and not the trailing data[] array:
struct hci_ev_le_per_adv_report {
__le16 sync_handle;
__u8 tx_power;
__u8 rssi;
__u8 cte_type;
__u8 data_status;
__u8 length;
__u8 data[];
} __packed;
The handler notifies the ISO layer via hci_proto_connect_ind(), which
reaches iso_connect_ind(). That function retrieves the stored event with
hci_recv_event_data() and, while reassembling the periodic advertising
data, does:
memcpy(hcon->le_per_adv_data + hcon->le_per_adv_data_offset,
ev->data, ev->length);
ev->length is taken directly from the event and is never validated
against the amount of data the event actually carries. A controller
that reports a length larger than the received event therefore causes
the memcpy() to read past the end of the event buffer. The leaked bytes
are stored in hcon->le_per_adv_data and can subsequently be read back
from user space via getsockopt(BT_ISO_BASE).
Validate that the event contains ev->length data bytes before it is
consumed, mirroring the check already performed by
hci_le_ext_adv_report_evt() and hci_le_adv_report_evt().
Signed-off-by: Laxman Acharya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btmtksdio_setup() calls pm_runtime_use_autosuspend() when runtime PM
is supported, but btmtksdio_remove() does not call the matching
pm_runtime_dont_use_autosuspend() when removing the device.
If the autosuspend delay is set to a negative value while autosuspend
is enabled, the runtime PM core increments usage_count to prevent
runtime suspend. Without calling pm_runtime_dont_use_autosuspend()
during driver teardown, this reference is not dropped and usage_count
remains unbalanced.
Add the missing pm_runtime_dont_use_autosuspend() call in the remove
path before restoring the runtime PM usage reference.
This issue was found by manual code inspection.
Fixes: 7f3c563c575e ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
mgmt_hci_cmd_sync() checks that the message length agrees with params_len
but puts no upper bound on it. params_len is __le16 while the parameter
length in the HCI command header is a u8:
struct hci_command_hdr {
__le16 opcode;
__u8 plen;
} __packed;
hci_cmd_sync_alloc() assigns one to the other:
hdr->plen = plen;
if (plen)
skb_put_data(skb, param, plen);
so a params_len of 256 leaves plen at 0 while all 256 bytes are still
appended. The frame handed to the driver then declares no parameters and
carries 256 of them. On a length framed transport such as H:4 the
controller takes the trailing bytes as the start of the next packet.
The mgmt socket MTU is HCI_MAX_FRAME_SIZE, so params_len can reach about
1KB this way. Commit 03f1700b9b4d ("Bluetooth: MGMT: reject malformed
HCI_CMD_SYNC commands") only made params_len agree with the message
length, a value that fits the message but not the header field is still
accepted.
Reject params_len that does not fit the header field.
Fixes: 827af4787e74 ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Cc: stable@vger.kernel.org
Signed-off-by: Ali Ahmet Memis <ali@iusegentoo.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Power supply to the M.2 Bluetooth device attached to the host using M.2
connector is controlled using the 'uart' pwrseq device. So add support
for getting the pwrseq device if the OF graph link is present.
Once obtained, pwrseq_power_on() is called to power up the M.2 Bluetooth
card. The power sequencer descriptor is obtained via pwrseq_get() with
the UART controller device (serdev->ctrl->dev), since the OF graph
link is defined on the UART controller node.
Also add the explicit pwrseq_put() call in all exit paths, pwrseq_put()
already calls pwrseq_power_off() internally, so no separate
pwrseq_power_off() call is needed.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
mgmt_hci_cmd_sync() queues the pending command with a NULL destroy
callback, so it is only freed if send_hci_cmd_sync() runs. A cancelled
entry is leaked, as _hci_cmd_sync_cancel_entry() does not release
entry->data when there is no destroy callback, and hci_cmd_sync_clear()
cancels every pending entry when the controller is unregistered. Nothing
else reclaims it either: mgmt_pending_new() does not put the command on
hdev->mgmt_pending.
The leak also pins the socket reference taken by mgmt_pending_new(), so
the mgmt socket is never released.
Free the command from a destroy callback. The now-empty done label is
replaced by a direct return.
Fixes: 827af4787e74 ("Bluetooth: MGMT: Add initial implementation of MGMT_OP_HCI_CMD_SYNC")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
mesh_send_cancel() queues the pending command with a NULL destroy
callback, so it is only freed if send_cancel() runs. A cancelled entry is
leaked, as _hci_cmd_sync_cancel_entry() does not release entry->data when
there is no destroy callback, and hci_cmd_sync_clear() cancels every
pending entry when the controller is unregistered. Nothing else reclaims
it either: mgmt_pending_new() does not put the command on
hdev->mgmt_pending.
The leak also pins the socket reference taken by mgmt_pending_new(), so
the mgmt socket is never released.
Free the command from a destroy callback.
Fixes: b338d91703fa ("Bluetooth: Implement support for Mesh")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
paths
adv_timeout_expire() hands a kmalloc()ed instance byte to
hci_cmd_sync_queue() with a NULL destroy callback, and only
adv_timeout_expire_sync() frees it. That leaks on two paths:
- the return value is not checked, and hci_cmd_sync_queue() does not
take ownership when it fails (-ENETDOWN, -ENODEV, -ENOMEM);
- a cancelled entry is not released, as _hci_cmd_sync_cancel_entry()
does not free entry->data when there is no destroy callback.
hci_cmd_sync_clear() cancels every pending entry when the controller
is unregistered.
Free the buffer from a destroy callback, and in the caller when the entry
could not be queued at all.
Fixes: c249ea9b4309 ("Bluetooth: Move Adv Instance timer to hci_sync")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_setup_sync() queues a conn_handle_t with a NULL destroy callback, so
the context is only freed if hci_enhanced_setup_sync() actually runs. An
entry that is cancelled instead is leaked, as
_hci_cmd_sync_cancel_entry() does not release entry->data when there is
no destroy callback, and hci_cmd_sync_clear() cancels every pending entry
when the controller is unregistered.
The context also stores a bare hci_conn pointer, so the connection can be
freed while the work is queued. The dequeue in hci_conn_del() does not
cover it either, as it matches on entry->data == conn and entry->data is
the wrapper here. Same problem as commit 2f5d635ad590 ("Bluetooth:
hci_sync: hold conn in hci_connect_acl/le_sync() callbacks").
Hold the connection and release both from a destroy callback. The
submission failure path drops both, since hci_cmd_sync_submit() does not
call the destroy callback when it fails to queue.
Fixes: e07a06b4eb41 ("Bluetooth: Convert SCO configure_datapath to hci_sync")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_update_event_filter_sync() walks hdev->accept_list while sending a
synchronous HCI command for each remote-wakeup device. The suspend path
holds hdev->req_lock, but accept-list updates are serialized by hdev->lock.
Consequently, remove_device() can free the current list entry during the
controller wait.
The following interleaving causes the use-after-free:
hci_update_event_filter_sync() remove_device()
fetch accept-list entry
hci_set_event_filter_sync()
wait for controller response hci_dev_lock()
list_del()
kfree()
hci_dev_unlock()
read the freed list.next
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_suspend_sync+0x835/0x910
Read of size 8 at addr ffff88810bec8440 by task kworker/0:1/10
Workqueue: events vhci_suspend_work
Call Trace:
hci_suspend_sync+0x835/0x910
hci_suspend_dev+0x182/0x450
process_one_work+0x661/0x1090
worker_thread+0x45b/0xd10
Allocated by task 86:
hci_bdaddr_list_add_with_flags+0x1a8/0x400
add_device+0x381/0x820
hci_sock_sendmsg+0x1033/0x1ea0
Freed by task 91:
kfree+0x131/0x3c0
remove_device+0x429/0xb70
hci_sock_sendmsg+0x1033/0x1ea0
Snapshot the remote-wakeup addresses under hdev->lock. Release the lock
before sending HCI commands. Clear the controller event filter before
building the snapshot, and skip allocation and the second list traversal
when there are no matching entries. This preserves the original filter
and scan-state updates without retaining an accept-list node across a
controller wait.
Fixes: 182ee45da083 ("Bluetooth: hci_sync: Rework hci_suspend_notifier")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-bluetooth/20260730092331.2069741-1-nicoyip.dev@gmail.com/
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_event_func() validates skb->len against ev->max_len from the
entry in hci_ev_table[]. By then, the header has already been
stripped by skb_pull(). So the max event payload is 255, but
hci_ev_table[] still uses HCI_MAX_EVENT_SIZE (260) for it, which is
imprecise.
Fix by introducing HCI_MAX_EVENT_PLEN (255) and using it instead.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Introduce the hook to solve issues below:
msft_vendor_evt(), the current handler for all VSEs, is unsuitable
since:
- many VSEs are not MSFT ones;
- it always corrupts the non-MSFT VSEs by calling skb_pull_data()
once the MSFT extension is enabled.
Several issues are caused by many transport drivers pre-processing
VSEs in their RX path, often an IRQ-disabled atomic context. Take
the two typical cases below as examples:
Case 1:
// no btmon log, no way to reach userspace
Step 1: handle and free @original_skb directly
Case 2:
// hurts performance and consumes GFP_ATOMIC memory
Step 1: cloned_skb = skb_clone(original_skb, GFP_ATOMIC);
// the VSE is handled here
Step 2: handle and free @cloned_skb
Step 3: hci_recv_frame(hdev, original_skb);
// already handled, but re-enters the stack's event-handling path
Step 4: hci_event_packet(hdev, original_skb);
Fix by introducing the hook with usage:
1) the transport driver registers the hook for VSEs of interest;
2) the stack calls it in process context, handling the VSE like any
other event:
- if interested, handle the VSE - no need to free it - and
return true;
- otherwise return false.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
nxp_set_ind_reset() injects the non-zero hardware error code
BTNXPUART_IR_HW_ERR.
Simplify it by __hci_reset_dev(hdev, BTNXPUART_IR_HW_ERR).
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_reset_dev() injects a constant hardware error code 0x00 to restart
the device. But a transport driver may need a different error code.
Fix by introducing __hci_reset_dev(hdev, hw_err_code), which will be
used by a follow-up patch.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
To separate the coredump header and data far more easily, give a
vendor driver the option to pad its header to a fixed size, by
moving the header size limit and ending marker to coredump.h:
- HCI_DEVCD_HDR_SIZE_MAX: the max header size
- HCI_DEVCD_HDR_END_MARKER: the header-ending marker
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Drop the check since:
- it is already implied by the existing (skb->len > HCI_EVENT_HDR_SIZE)
- hdr->plen is then not used by the function at all
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
For a diagnostics VSE, diagnostics_hdr[] sits at the start of the event
payload, skb->data[2], but btintel_recv_event() wrongly guards its
memcmp with @len, which is measured from skb->data[3] for the earlier
INTEL_BOOTLOADER check.
Fix by using (@len + 1) instead, which ==
(skb->len - HCI_EVENT_HDR_SIZE) exactly.
Fixes: af395330abed ("Bluetooth: btintel: Add Intel devcoredump support")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The Command Complete dispatch validates only the fixed part of the LE Set
CIG Parameters response. After that part is pulled from the skb,
hci_cc_le_set_cig_params() trusts num_handles and reads each entry in the
trailing handle array.
Matching num_handles against the command's num_cis does not guarantee
that the response contains the advertised handles. A truncated response
from a malfunctioning controller can therefore make the handler read
beyond the skb data.
Validate that the remaining skb data contains all advertised handles.
Include this in the existing response validation so malformed responses
also follow the established CIG failure handling.
Fixes: 26afbd826ee3 ("Bluetooth: Add initial implementation of CIS connections")
Cc: stable@vger.kernel.org
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The event length validation added by 65be90af2756 commit used a single
check against sizeof(*event), which assumed every event type uses the
maximum payload size. Unfortunately event packet length depends on the
type of the received event, so it must be checked separately for each
event type to avoid rejecting some known well-formed events.
Fixes: 65be90af2756 ("Bluetooth: btmrvl: validate event packet lengths")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add context analysis annotations for hci_conn::l2cap_data locking.
Also add necessary lockdep_assert_held() and __must_hold annotations
to prove the access is safe.
The access in smp_conn_security() is supposed to be guarded by the
caller holding lock that blocks concurrent l2cap_conn_del() eg.
hdev->lock, conn->lock or chan->lock. Mark unsafe as can't be
automatically checked now.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_conn::l2cap_data is accessed without locks in l2cap_disconn_ind via
hci_conn_timeout (disc_work) -> hci_proto_disconn_ind ->
l2cap_disconn_ind. This is UAF if the l2cap_conn is deleted
concurrently.
disc_work is disabled sync in hci_conn_del(), so we cannot take
hci_dev_lock in disc_work.
Fix by using proto_lock to guard l2cap_data, in addition to hdev->lock
which is held in other access paths.
Fixes: ab4eedb790ca ("Bluetooth: L2CAP: Fix corrupted list in hci_chan_del")
Reported-by: syzbot+9c40ad7c6ed7165e46e8@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9c40ad7c6ed7165e46e8
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The virtbt_setup_zephyr() sends the Zephyr vendor command 0xfc08 (Read
Build Information) and hands the response to bt_dev_info() and
hci_set_fw_info() as a "%s" string starting at skb->data + 1, without
checking the length. A backend that answers with status only leaves that
pointer past the end of the received data, so the walk reads adjacent
slab memory until it meets a NUL. Those bytes reach the kernel log and
the firmware-info debugfs file.
To fix this, print the string with a bounded "%.*s" limited to
skb->len - 1. A short or unterminated response then prints as much as
arrived instead of failing setup.
This mirrors commit dd068ef04412 ("Bluetooth: bpa10x: avoid OOB read of
revision string in bpa10x_setup()"), which fixed the identical pattern.
Fixes: afd2daa26c7a ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: HyeongJun An <sammiee5311@gmail.com>
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Removed a redundant braces for a single if statement
Signed-off-by: Oshada Imalka <developerimalka@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_cc_reset() clears the LE accept and resolving lists without taking
hdev->lock. Other command-complete handlers serialize updates to these
lists with that lock, and the debugfs readers hold it while walking them.
This permits the reset completion and a debugfs read to interleave as
follows:
hci_rx_work debugfs reader
----------- --------------
lock hdev->lock
fetch current entry
list_del(entry)
kfree(entry)
read entry fields
The reader then dereferences a freed list entry and may follow its stale
next pointer.
KASAN reported:
BUG: KASAN: slab-use-after-free in white_list_show+0x15f/0x180
Read of size 1 at addr ffff8881015dab16 by task poc/95
Call Trace:
white_list_show+0x15f/0x180
seq_read_iter+0x3ff/0x1190
seq_read+0x267/0x3d0
vfs_read+0x177/0xa20
ksys_read+0xf7/0x1c0
Allocated by task 91:
hci_bdaddr_list_add+0x1a6/0x3a0
hci_cc_le_add_to_accept_list+0xab/0x140
hci_cmd_complete_evt+0x26c/0x9a0
hci_event_packet+0x454/0xb20
hci_rx_work+0x293/0x730
Freed by task 90:
kfree+0x131/0x3c0
hci_bdaddr_list_clear+0xd8/0x160
hci_cc_reset+0x28a/0x370
hci_cmd_complete_evt+0x26c/0x9a0
hci_event_packet+0x454/0xb20
hci_rx_work+0x293/0x730
Take hdev->lock around both list clears. This matches the existing
mutation and traversal locking convention.
Fixes: a4d5504d5c39 ("Bluetooth: Clear LE white list when resetting controller")
Fixes: cfdb0c2d095a ("Bluetooth: Store Resolv list size")
Cc: stable@vger.kernel.org
Signed-off-by: Chengfeng Ye <nicoyip.dev@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
aml_download_firmware() reads two lengths from the firmware header and
uses them to build pointers before checking that the header and segment
data are present. A truncated or inconsistent firmware image can make
the driver read past firmware->data while constructing TCI commands.
Reject images shorter than the header and ensure that the ICCM and DCCM
ranges fit within the loaded firmware before downloading either segment.
Fixes: 37bac77e4649 ("Bluetooth: hci_uart: Add support for Amlogic HCI UART")
Cc: stable@vger.kernel.org
Signed-off-by: Laxman Acharya Padhya <acharyalaxman8848@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BRDS revision 2 introduces per-chain (Chain A and Chain B) TX power
limits across five sub-bands (2.4G, 5.2G, 5.8/5.9G, 6G-low, 6G-high),
replacing the single-chain per-modulation model of revisions 0 and 1.
- Add btintel_set_sar_rev2() which sends the full Rev2 DDC sequence:
0x019e inc-power-mode enable flag (1 byte)
0x0311 2.4 GHz sub-band limits (2 bytes)
0x0312 5.2 GHz sub-band limits (2 bytes)
0x0313 5.8/5.9 GHz sub-band limits (2 bytes)
0x0314 5.8/5.9 GHz sub-band limits again (2 bytes, duplicate FW reg)
0x0315 6 GHz low sub-band limits (2 bytes)
0x0316 6 GHz high sub-band limits (2 bytes)
followed by the SAR-init-complete command (0xfe25).
logs from dmesg when BTSAR2 is enabled in Coreboot/BIOS:
Bluetooth: hci0: BT SAR Rev2: revision=2 bt_sar_bios=1 inc_power_mode=1
Bluetooth: hci0: BT SAR Rev2 Chain A: 2g4=76 5g2=0 5g8_5g9=0 6g1=0 6g3=0
Bluetooth: hci0: BT SAR Rev2 Chain B: 2g4=102 5g2=0 5g8_5g9=0 6g1=0 6g3=0
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add MGMT_OP_LOAD_CONN_SUBRATE (0x005C) command to load per-device
connection subrate parameters when the SCI feature is supported.
Add MGMT_EV_CONN_SUBRATE (0x0033) event to notify userspace when
connection rate changes occur via the LE Connection Rate Change HCI
event.
Add subrate fields (subrate_min, subrate_max, max_latency, cont_num)
to struct hci_conn_params to store the loaded subrate parameters, and
the corresponding le_rate_* fields to struct hci_conn to track the
parameters currently in use.
When a single entry is loaded for an already-connected central, or on
connection completion, the LE Connection Rate Request procedure is
initiated to apply the parameters.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add MGMT_SETTING_SCI (bit 25) to advertise support for the Shorter
Connection Interval (SCI) feature. It is reported in the supported
settings whenever the controller is SCI capable, and in the current
settings whenever LE is enabled and the controller is SCI capable
(SCI has no separate enable command, so it is a passive capability).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add HCI command, event and feature bit definitions for the Bluetooth
6.2 Shorter Connection Interval feature:
Commands:
- HCI_OP_LE_CONN_RATE (0x20a1) - Connection Rate Request
- HCI_OP_LE_SET_DEF_RATE (0x20a2) - Set Default Rate Parameters
- HCI_OP_LE_READ_CONN_INTERVAL (0x20a3) - Read Min Supported
Connection Interval
Events:
- HCI_EVT_LE_CONN_RATE_CHANGE (0x37) - Connection Rate Change
Feature bits:
- HCI_LE_SCI - Shorter Connection Intervals
- HCI_LE_SCI_HOST - Shorter Connection Intervals (Host Support)
During controller init, when SCI is supported:
- Set Shorter Connection Intervals (Host Support) feature via
LE Set Host Feature
- Read Minimum Supported Connection Interval
- Set Default Rate Parameters
The Connection Rate Change event handler updates the connection
interval, latency and supervision timeout on the hci_conn.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add a read-write sysfs entry at /sys/bus/pci/devices/<BDF>/vendor_reset
to allow userspace to trigger PLDR (Product Level Device Reset).
Reading the attribute displays supported reset types. Writing
integer 0 triggers PLDR. Any other input is rejected with
-EINVAL and a warning log.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This module sets the acpi_device_id::driver_data to 0 but
the field is not actually used within the module, we can
just drop it from the table.
While we are at it - use a named initializer for the
acpi_device_id::id field and drop setting the list
terminator fields explicitly as well.
Signed-off-by: Pawel Zalewski (The Capable Hub) <pzalewski@thegoodpenguin.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use a named initializer for the acpi_device_id fields which
makes the code more readable and consistent with how lists
are initialized in the rest of the kernel code base.
While we are at it - unify the list terminator to have
a single space between the brackets without a trailing
coma.
Signed-off-by: Pawel Zalewski (The Capable Hub) <pzalewski@thegoodpenguin.co.uk>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
For a HCI_VENDOR_PKT frame, hci_recv_frame() does not accept it and
will kfree_skb() it directly.
But btmrvl_sdio_card_to_host() is still calling hci_recv_frame() for
the frame.
Fix by freeing it with kfree_skb() directly.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Simplify btintel_classify_pkt_type() by using hci_acl_handle() instead of:
__u16 handle = __le16_to_cpu(hci_acl_hdr(skb)->handle);
... hci_handle(handle) ...
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Simplify btusb_recv_bulk() by using hci_acl_dlen() instead of:
__le16 dlen = hci_acl_hdr(skb)->dlen;
... __le16_to_cpu(dlen) ...
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Simplify hci_recv_frame() by using hci_acl_handle() instead of:
__u16 handle = __le16_to_cpu(hci_acl_hdr(skb)->handle);
... hci_handle(handle) ...
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Introduce both helpers for ACL packet since:
both core and transport drivers extract the handle and data length
from its header in several places.
Both will be used later.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add btusb_prepare_reset() to do cleanup before a reset, and
apply it to btusb_mtk_reset() as well.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Both helpers currently take struct btusb_data *, which is private to
btusb.c, as parameter type as below:
int btusb_recv_event(struct btusb_data *data, struct sk_buff *skb)
int btusb_recv_acl(struct btusb_data *data, struct sk_buff *skb)
To allow vendor USB-transport-specific source files to share them as
well, change the type to struct hci_dev *.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Introduce hci_devcd_state_name() to describe the devcoredump state by a
string name instead of a plain number, for several reasons:
1) Applying it in coredump.c makes the devcoredump state in log messages
more readable than a plain number.
2) Transport drivers may need to show the devcoredump state name too.
3) In future, the universal state name could be notified to userspace
via uevent, allowing a universal application (e.g. a daemon) to be
developed to save the coredump, which is otherwise discarded by the
device coredump core after 5 minutes (DEVCD_TIMEOUT); see
nxp_coredump_notify().
Also drop a trailing space from two bt_dev_dbg() format strings while
applying it in coredump.c.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The modules rfcomm (BT_RFCOMM), bnep (BT_BNEP), hidp (BT_HIDP), and
bluetooth_6lowpan (BT_6LOWPAN) are dependent on the bluetooth module
(BT, tristate) only transitively through the boolean BT_BREDR for the
first three and through the boolean BT_LE for the bluetooth_6lowpan.
Therefore, the modules can be selected as built-in even if the BT=m.
The combination of BT=m and =y for the said modules leads to the kernel
build system silently ignoring those modules, without ever compiling
them as built-in or as loadable modules.
Add BT as a direct dependency to the Kconfig of rfcomm, bnep, hidp, and
bluetooth_6lowpan. The modules set to =y when BT=m will default to =m,
rather then getting silently ignored by the build system.
Signed-off-by: Iva Kasprzaková <iva@yenya.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In rsi_hci_attach(), ops->set_bt_context() stores the newly allocated
h_adapter into common->bt_adapter before hci_alloc_dev() and
hci_register_dev() are called. If either of these fails, h_adapter
is freed but common->bt_adapter remains a non-NULL dangling pointer.
This causes a deterministically reachable use-after-free when the
device operates in a BT+WiFi coexistence mode and CONFIG_RSI_COEX
is enabled. The following software-only trigger paths exist:
1. SDIO driver .remove (rsi_disconnect)
2. USB driver .disconnect (rsi_disconnect)
3. SDIO driver .shutdown (rsi_shutdown)
4. Hibernation .freeze (rsi_freeze)
All four paths check:
if (IS_ENABLED(CONFIG_RSI_COEX) && coex_mode > 1 && bt_adapter)
rsi_bt_ops.detach(bt_adapter); // use-after-free
coex_mode is set during rsi_91x_init(), before rsi_hci_attach() is
called, and is not cleared on attach failure. Since set_bt_context()
already wrote bt_adapter before the failure, the deinit paths see a
non-NULL dangling pointer and proceed to detach it.
Fix this by moving set_bt_context() after hci_register_dev() succeeds.
On failure paths bt_adapter stays NULL, and the deinit callers correctly
skip the detach call.
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In the switch-case block for hardware variant detection, the
default case has an unreachable 'break' statement following
'goto exit_error'. Remove the dead code.
Signed-off-by: Chen Changcheng <chenchangcheng@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The macros below have different meanings even though they share the
same value 0xff:
HCI_VENDOR_PKT: HCI packet indicator or type
HCI_EV_VENDOR: event code of a VSE
This usage of HCI_VENDOR_PKT is wrongly checking an event code.
Fix by using HCI_EV_VENDOR for event code.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The macros below have different meanings even though they share the
same value 0xff:
HCI_VENDOR_PKT: HCI packet indicator or type
HCI_EV_VENDOR: event code of a VSE
These usages of HCI_VENDOR_PKT are wrongly checking an event code.
Fix by using HCI_EV_VENDOR for event code.
Also fix warning "CHECK: Unnecessary parentheses around comparison"
given by checkpatch.pl.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The macros below have different meanings even though they share the
same value 0xff:
HCI_VENDOR_PKT: HCI packet indicator or type
HCI_EV_VENDOR: event code of a VSE
This usage of HCI_VENDOR_PKT is wrongly checking an event code.
Fix by using HCI_EV_VENDOR for event code.
Also fix warning "CHECK: Unnecessary parentheses around comparison"
given by checkpatch.pl.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The HCI UART write worker assumes that a tty write callback returns a
value in the range from zero through the skb length. A negative value or
a value larger than the skb length is passed to accounting and skb_pull,
which can corrupt skb state.
Treat either return value as a transmit error and discard the skb.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The BCSP transmit path reads an HCI command header when an extension
packet has only been tested for a nonzero length. Its LE configuration
packet handler also indexes bytes through offset seven without a length
check.
Validate the complete command and LE configuration packet headers
before accessing their fields.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The Marvell event handlers access the HCI event header, command
complete payload, and driver-specific event header before validating
that the received skb contains them. A truncated event can consequently
cause an out-of-bounds read.
Validate each header and the command-complete payload length before
dereferencing the corresponding fields.
Signed-off-by: Li Qiang <liqiang01@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
- Avoid using deep idle states during initialization in the intel_idle
driver to work around device handling issues (Rafael Wysocki)
- Fix and refactor the ACPI processor driver code related to ACPI _LPI
support and add ACPI _LPI support to intel_idle based on that ACPI
processor driver update (Rafael Wysocki)
* pm-cpuidle:
intel_idle: Avoid using deep idle states during initialization
intel_idle: Update documentation after adding ACPI _LPI support
intel_idle: Add ACPI _LPI support
intel_idle: Prepare for adding ACPI _LPI support
ACPI: processor: idle: Add switch for strict _LPI processing
ACPI: processor: idle: Relocate acpi_processor_extract_lpi_info()
ACPI: processor: idle: Introduce acpi_processor_extract_lpi_info()
ACPI: processor: idle: Introduce too_many_states() for _LPI
ACPI: processor: idle: Rework flatten_lpi_states()
ACPI: processor: idle: Rearrange loop in acpi_processor_get_lpi_info()
ACPI: processor: idle: Drop redundant _LPI presence checks
ACPI: processor: idle: Rework first-level _LPI states processing
ACPI: processor: idle: Rearrange acpi_processor_get_lpi_info()
ACPI: processor: idle: Introduce lpi_state_debug()
ACPI: processor: idle: Split acpi_processor_evaluate_lpi()
ACPI: processor: idle: Rearrange acpi_processor_evaluate_lpi()
ACPI: processor: idle: Unify debug in acpi_processor_evaluate_lpi()
ACPI: processor: idle: Ignore _LPI states with SYSTEMIO entry method
ACPI: processor: idle: Expand _LPI package sanity checks
|
