| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
and complete examples
Add adi,vout-rfb1-ohms and adi,vout-rfb2-ohms properties to support
external voltage divider configuration for VOUT sensing. When the
desired output voltage is higher than VREF, a resistor divider (RFB1
and RFB2) is required to reach the intended value.
The properties use a dependency constraint to ensure both resistors
are specified together, or neither. This prevents misconfiguration
where only one resistor value is provided.
This patch also adds missing entries in the examples.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Link: https://lore.kernel.org/r/20260730-dev-max20830c-v5-1-a7553f84ee74@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Some PMBus chips do not support the PMBUS_REVISION command. Knowing
the PMBUs revision supported by a chip is relevant for PMBUs core
functionality, so add support for letting chip drivers report the PMBUs
revision.
Use the new capability to report the PMBus revision supported by MAX20830.
While at it, add definitions for PMBUs revisons 1.3.1 and 1.4.
Cc: Nuno Sá <nuno.sa@analog.com>
Cc: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Kraken 2024 Elite (USB ID 1e71:3012) is protocol-compatible with the
existing Kraken 2023 devices and works with the current Z53 code paths.
Add its USB product ID and map it to the KRAKEN2023 kind.
Tested on hardware: liquid temperature and pump/fan speeds read
correctly (cross-checked against liquidctl), and PWM control of both the
pump and fan channels works as expected.
Signed-off-by: Sean Lyon <sean@seanlyon.dev>
Link: https://lore.kernel.org/r/20260728031127.26553-1-sean@seanlyon.dev
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Volterra VT7505
Add a PMBus driver for the Analog Devices MAX16545 and MAX16550, and the
Volterra VT7505 controllers. The driver reports input/output voltage,
input/output current, input power and temperature over PMBus. All values
use the direct data format. Peak input voltage, output voltage, output
current, input power and temperature readings are exposed and can be
reset.
The reported current and power depend on the external current-report
resistor connected to the ILOAD pin, which can be provided through the
"adi,rload-ohms" device tree property.
On the MAX16550 and VT7505, the severe-OCP deglitch time can optionally
be configured with the "adi,ocp-severe-filter-us" device tree property.
When omitted, the existing hardware setting is left unchanged.
Co-developed-by: Dhruva Devineni <ddevineni@juniper.net>
Co-developed-by: Debjit Ghosh <dghosh@juniper.net>
Co-developed-by: JawaharBalaji Thirumalaisamy <jawaharb@juniper.net>
Co-developed-by: Avadhut Naik <avadhutn@juniper.net>
Co-developed-by: Santhanakrishnan Balraj <sbalraj@juniper.net>
Co-developed-by: Brian Mak <makb@juniper.net>
Signed-off-by: Georgi Vlaev <gvlaev@juniper.net>
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260725211945.288415-3-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
VT7505
Add device tree binding documentation for the Analog Devices MAX16545 and
MAX16550, and the Volterra VT7505 PMBus controllers.
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260725211945.288415-2-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Document the sysfs and debugfs interfaces of the Kandou KB9002 hwmon
driver.
Signed-off-by: Andy Chung <Andy.Chung@amd.com>
Link: https://lore.kernel.org/r/20260724-kb9002-upstream-v5-4-9523c3ffe83a@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Kandou KB9002 is an 8-lane PCIe 5.0 retimer that exposes an SMBus
target with mandatory PEC. Add a hwmon driver reporting the firmware
aggregated maximum die temperature as temp1_input, with the firmware
version and boot status under debugfs.
Signed-off-by: Andy Chung <Andy.Chung@amd.com>
Link: https://lore.kernel.org/r/20260724-kb9002-upstream-v5-3-9523c3ffe83a@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Kandou KB9002 is an 8-lane PCIe 5.0 retimer exposing an SMBus target
that reports an aggregated die temperature. It needs no device-specific
device tree properties beyond its address, so add it to trivial-devices.
Signed-off-by: Andy Chung <Andy.Chung@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724-kb9002-upstream-v5-2-9523c3ffe83a@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Kandou AI is the vendor of the KB9002 PCIe retimer.
Signed-off-by: Andy Chung <Andy.Chung@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260724-kb9002-upstream-v5-1-9523c3ffe83a@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix spelling error reported by codespell:
supprts -> supports
No functional change.
Signed-off-by: shaikh.kamal <shaikhkamal2012@gmail.com>
Link: https://lore.kernel.org/r/20260726065835.21012-1-shaikhkamal2012@gmail.com
[groeck: Move driver name to subject line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Coverity reports dead code in mp2975_data2reg_linear11(). Code analysis
shows that the parameter passed to the function is always non-negative.
This means that negative values do not need to be handled, and the
associated variable and conditional code can be removed.
No functional impact or change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver registers ltc4283_of_match as the platform driver's
.of_match_table so the kernel probes the device when a DT node with
compatible "adi,ltc4283" is present, but the corresponding
MODULE_DEVICE_TABLE(of, ...) call is absent.
Without it the module alias table (modules.alias) does not contain an
"of:N*T*Cadi,ltc4283" entry, so udev / kmod cannot auto-load the
module when the DT node appears, breaking modules-based deployments
while built-in configurations happen to work by accident.
Add the missing MODULE_DEVICE_TABLE() to fix module auto-loading.
Fixes: dd63353a0b5e ("hwmon: ltc4283: Add support for the LTC4283 Swap Controller")
Signed-off-by: surendra <kr494167@gmail.com>
Link: https://lore.kernel.org/r/20260721055022.34629-1-kr494167@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for Maxim MAX34452 PMBus 16-Channel V/I Monitor and
12-Channel Sequencer/Marginer. The device is similar to MAX34451
and shares the same configuration function.
The MAX34452 supports:
- 16 configurable voltage/current monitoring channels
- 5 temperature sensors (pages 16-20)
- Dynamic channel configuration via MFR_CHANNEL_CONFIG
- IOUT average monitoring
Signed-off-by: Carlos Jones Jr <carlosjr.jones@analog.com>
Co-Developed by: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Signed-off-by: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Link: https://lore.kernel.org/r/20260722-max34451_fixes-v2-3-bbddb18ec1d6@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The MAX34451 released a newer version called max34451etna8+.
This simply changes the direct format coefficients
Signed-off-by: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Link: https://lore.kernel.org/r/20260722-max34451_fixes-v2-2-bbddb18ec1d6@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The fan driver now is independent of the fan plreg GPIO information.
Therefore there will no longer be presence or fail information available
from the driver. Part of the changes includes removing a system power check
as the GPIO driver needs it to report power state to host.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230705194544.100370-5-nick.hawkins@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reduce the hpe,gxp-fan-ctrl register references from 3 to 1. The
function2 (fn2) and programmable logic (pl) references are removed.
The purpose of removal being their functionality will be consumed by a
new GPIO driver.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230705194544.100370-4-nick.hawkins@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_threaded_irq() automatically logs
detailed error messages on failure. Remove the now-redundant
driver-specific dev_err() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-8-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_irq() automatically logs detailed
error messages on failure. Remove the now-redundant driver-specific
dev_err() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-7-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_irq() automatically logs detailed
error messages on failure. Remove the now-redundant driver-specific
dev_err() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-6-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_irq() automatically logs detailed
error messages on failure. Remove the now-redundant driver-specific
dev_err() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-5-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_threaded_irq() automatically logs
detailed error messages on failure. Remove the now-redundant
driver-specific dev_err() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-4-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_threaded_irq() automatically logs
detailed error messages on failure. Remove the now-redundant
driver-specific dev_err() call.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-3-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since commit 55b48e23f5c4 ("genirq/devres: Add error handling in
devm_request_*_irq()"), devm_request_threaded_irq() automatically logs
detailed error messages on failure. Remove the now-redundant
driver-specific dev_err() calls.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://lore.kernel.org/r/20260720063745.309331-2-panchuang@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The legacy hwmon_device_register() function is deprecated and triggers
warnings in dmesg. Convert the driver to the modern
hwmon_device_register_with_info() API.
This conversion does the following:
- Dynamically allocates standard HWMON temp, fan, and pwm channels.
- Configures HWMON ops callbacks (.is_visible, .read, .read_string, .write).
- Standardizes attribute naming to match the HWMON ABI:
- fanX_output -> fanX_target (HWMON_F_TARGET)
- fanX_manual -> pwmX_enable (HWMON_PWM_ENABLE)
- Dynamically registers non-standard fanX_safe attributes under the HWMON
class directory via extra_groups.
- Cleans up legacy sysfs nodes, groups, and unused show/store static functions
to avoid unused symbol compiler warnings.
- Avoids recursive mutex deadlocks when writing to pwmX_enable by locklessly
resolving the entry and invoking the underlying raw SMC read/write calls.
- Avoids UAF race condition on module exit by using unmanaged registration and
explicitly calling hwmon_device_unregister() as the first step of applesmc_exit(),
guaranteeing that HWMON nodes are destroyed before static structures are freed.
Signed-off-by: Shih-Yuan Lee <fourdollars@debian.org>
Link: https://lore.kernel.org/r/20260711093323.14529-4-fourdollars@debian.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In applesmc_get_entry_by_index(), the cache->valid flag is checked
locklessly, but setting it to true lacks memory barriers. This can lead to
a data race (TOCTOU) where another thread sees cache->valid as true
before the actual cache contents (cache->key, cache->len, cache->type, etc.)
are fully committed and visible to that CPU, potentially causing it to read
uninitialized data and send incorrect keys to the Apple SMC hardware.
Introduce memory barriers (smp_load_acquire and smp_store_release) with
explanatory comments to ensure cache synchronization is thread-safe and
fully visible across all CPUs.
Signed-off-by: Shih-Yuan Lee <fourdollars@debian.org>
Link: https://lore.kernel.org/r/20260711093323.14529-3-fourdollars@debian.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
To support the read_string callback for fan labels in the modern HWMON
API, load and cache the fan position names in smcreg.fan_positions
during register initialization.
Pre-pad fallback labels with four spaces to match the "+ 4" pointer
arithmetic offset used by all fan labels in the read_string callback.
Signed-off-by: Shih-Yuan Lee <fourdollars@debian.org>
Link: https://lore.kernel.org/r/20260711093323.14529-2-fourdollars@debian.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
To guarantee consistency for the read-modify-write access in
cros_ec_hwmon_cooling_set_cur_state(), locking is necessary.
Use the existing hwmon device lock to do so.
Fixes: 5798b62867b4 ("hwmon: (cros_ec) register fans into thermal framework cooling devices")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20260711-cros_ec-hwmon-locking-v1-3-cb6d0fdbb2d3@weissschuh.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The upcoming locking scheme for thermal devices will require access
to the hwmon device.
Add it do the priv struct.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20260711-cros_ec-hwmon-locking-v1-2-cb6d0fdbb2d3@weissschuh.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
To guarantee consistency for the read-modify-write access in
cros_ec_hwmon_cooling_set_cur_state(), locking is necessary.
The locking will use standard hwmon device locks, which requires
the hwmon device to be ready before the fan devices are set up.
Reorder the initialization so this works.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20260711-cros_ec-hwmon-locking-v1-1-cb6d0fdbb2d3@weissschuh.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver has a match table for the i2c bus wired into its driver
structure, but the table is not exported with MODULE_DEVICE_TABLE().
Add the missing MODULE_DEVICE_TABLE() entry so module alias information
is generated for automatic module loading.
This is a source-level fix. It does not claim dynamic hardware
reproduction; the evidence is the driver-owned match table, its use by
the driver registration structure, and the missing module alias
publication.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20260704151543.35069-1-pengpeng@iscas.ac.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for MPS mpq82d00 controller. This driver exposes
telemetry and limit value readings and writtings.
Signed-off-by: Wensheng Wang <wenswang@yeah.net>
Link: https://lore.kernel.org/r/20260704081952.1701914-2-wenswang@yeah.net
[groeck: Fixed "WARNING: Title underline too short"]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for MPS mpq82d00 controller.
Signed-off-by: Wensheng Wang <wenswang@yeah.net>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20260704081952.1701914-1-wenswang@yeah.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
scripts/kernel-doc -Wall -none reports:
Warning: drivers/hwmon/peci/common.h:39 function parameter 'state' not
described in 'peci_sensor_need_update'
Warning: drivers/hwmon/peci/common.h:39 Excess function parameter
'sensor' description in 'peci_sensor_need_update'
Warning: drivers/hwmon/peci/common.h:49 function parameter 'state' not
described in 'peci_sensor_mark_updated'
Warning: drivers/hwmon/peci/common.h:49 Excess function parameter
'sensor' description in 'peci_sensor_mark_updated'
Both peci_sensor_need_update() and peci_sensor_mark_updated() take a
pointer to struct peci_sensor_state named 'state', but their kernel-doc
comments document a parameter named 'sensor' and describe it as a
pointer to the sensor data struct. The comments have been out of sync
with the code since the file was added by commit bf3608f338e9 ("hwmon:
peci: Add cputemp driver").
Update the kernel-doc comments to document the 'state' parameter.
No functional change.
Assisted-by: Claude:claude-sonnet-5
Signed-off-by: Babanpreet Singh <bbnpreetsingh@gmail.com>
Link: https://lore.kernel.org/r/20260712081258.7-1-bbnpreetsingh@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The GXCAS GXHT30 is a humidity and temperature sensor that is a
drop-in replacement for and fully software compatible with the
Sensirion SHT30.
It is handled by the "sensirion,sht30" fallback compatible without
any driver changes; manual instantiation works with the existing
sht3x device name. Document the chip as supported.
Signed-off-by: Zaixiang Xu <zaixiang.xu.dev@gmail.com>
Link: https://lore.kernel.org/r/20260713074559.12196-5-zaixiang.xu.dev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add an of_device_id table to support devicetree based instantiation
of the supported sensors.
The devicetree binding models all higher accuracy parts with a
fallback to the base part of their group, so only the two base
compatibles need to be listed. The match data distinguishes the
humidity and temperature parts (SHT3x) from the temperature-only
parts (STS3x), which require different configuration.
Start enum sht3x_chips at 1: with sht3x equal to 0, the OF match
data for the SHT devices would be NULL, causing i2c_get_match_data()
to fall back to i2c_device_id name matching, which fails for
devicetree names. The devices would then only work because the
resulting chip id 0 happens to equal sht3x. Non-zero match data
avoids relying on that coincidence.
Signed-off-by: Zaixiang Xu <zaixiang.xu.dev@gmail.com>
Link: https://lore.kernel.org/r/20260713074559.12196-4-zaixiang.xu.dev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a YAML devicetree binding for the Sensirion SHT3x/STS3x sensor
family and the compatible GXCAS GXHT30, with the ALERT interrupt,
nRESET GPIO and VDD supply as optional properties.
The SHT30, SHT31, SHT35 and SHT85 measure humidity and temperature
and differ only in accuracy and packaging, while the STS30, STS31,
STS32 and STS35 are temperature-only parts. Within each group the
parts share the same software interface, so model them with a
fallback to the base part of their group: "sensirion,sht30" for the
SHT parts and "sensirion,sts30" for the STS parts.
The GXCAS GXHT30 is a drop-in replacement for the SHT30 and uses it
as fallback as well.
Signed-off-by: Zaixiang Xu <zaixiang.xu.dev@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260713074559.12196-3-zaixiang.xu.dev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add vendor prefix for Beijing Galaxy-CAS Technology Co., Ltd. (GXCAS).
The prefix was confirmed from the manufacturer's website:
https://www.gxcas.com/en/index.html
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Zaixiang Xu <zaixiang.xu.dev@gmail.com>
Link: https://lore.kernel.org/r/20260713074559.12196-2-zaixiang.xu.dev@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When there is no physical sensor connected to the motherboard
socket,reading EC register returns one of the special values
(-62, -60, -40). Test for them and return -ENODATA to hwmon.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20260711122937.594989-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Enable T_Sensor for ROG STRIX X870E-E GAMING WIFI.
Board specs list the sensor, reading at the standard for this family
address without the thermistor connected to the motherboard, returns
-62, which is one of the known blank values (the other one in -40)
readings for temperature sensors in the ASUS EC when there is no
thermistor connected to the motherboard socket. With that evidence we
conclude that the T_Sensor can be enabled in the driver for this board.
Signed-off-by: Vishaal Saraiya <vishaal.saraiya@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20260711073319.553163-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
tmp401 is missing HWMON_C_REGISTER_TZ. So a devicetree thermal
zone referencing a such sensor ('thermal-sensors = <&tmp411 N>')
fails to register it. Then its cooling-maps is not set, which means
that the fans are not managed.
Same as lm90 or jc42, set HWMON_C_REGISTER_TZ.
Boards without the property into the DT keep the same behavior.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Link: https://lore.kernel.org/r/20260713-for-upstream-hwmon-tmp401-register-tz-v1-1-47315d8617bc@free.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the ProArt Z690-CREATOR WIFI board
Signed-off-by: Maurice Mehlhaff <maurice.mehlhaff@gmx.de>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20260708195638.1324168-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add the Lenovo LOQ 15IAX9 product family to the yogafan dmi_system_id
table. Unlike the Legion series, ACPI table extraction reveals this LOQ
utilizes an 8-bit EC architecture with a 100x multiplier, but maintains
a dual-fan setup via the \_SB.PC00.LPCB.EC0.FA1S and FA2S paths.
A new loq_15iax9_8bit_dual_cfg structure was added to properly map these
hardware registers and calculate RPMs correctly while avoiding path
conflicts with AMD-based LOQ variants.
Signed-off-by: Sarbajit Sarkar <sarbajitsarkar16108@gmail.com>
Link: https://lore.kernel.org/r/20260709183500.13761-1-sarbajitsarkar16108@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The board sensors is a copy of ROG STRIX X870E-E GAMING WIFI7, thus we
simply reuse its board_info struct.
Signed-off-by: Vishaal Saraiya <vishaal.saraiya@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20260709204037.1998433-3-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for ROG CROSSHAIR X870E HERO
Signed-off-by: Miska Hämäläinen <miska.hamalainen@hotmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20260705113246.812500-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for ROG Maximus Z790 Hero.
Signed-off-by: Florian Schut <mail@florianschut.nl>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20260705113125.812045-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver populates acpi_device_name() and acpi_device_class() that are
never read afterward, so make it stop doing that and drop the symbols
defined for this purpose.
Since ACPI_POWER_METER_CLASS is also used for generating ACPI netlink
events, use the "pwr_meter_resource" string literal directly instead of
it for that.
No intentional functional impact.
This will facilitate the removal of device_name and device_class from
struct acpi_device_pnp in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/2297496.irdbgypaU6@rafael.j.wysocki
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for ESWIN EIC7700 Voltage and Temperature sensor. The driver
supports temperature and voltage monitoring with polynomial conversion,
and provides sysfs interface for sensor data access.
The PVT IP contains one temperature sensor and one voltage sensor.
Signed-off-by: Yulin Lu <luyulin@eswincomputing.com>
Signed-off-by: Huan He <hehuan1@eswincomputing.com>
Signed-off-by: Xuyang Dong <dongxuyang@eswincomputing.com>
Link: https://lore.kernel.org/r/20260630091220.1608-1-dongxuyang@eswincomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add device tree binding documentation for ESWIN EIC7700 Voltage and
Temperature sensor.
The EIC7700 SoC integrates two PVT instances for monitoring SoC and DDR
power domains respectively.
Signed-off-by: Yulin Lu <luyulin@eswincomputing.com>
Signed-off-by: Huan He <hehuan1@eswincomputing.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Xuyang Dong <dongxuyang@eswincomputing.com>
Link: https://lore.kernel.org/r/20260630091122.1462-1-dongxuyang@eswincomputing.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ChromeOS EC APIs use integers representing degrees kelvin for
temperatures. The default conversions from linux/units.h will then
always convert these integer degrees celsius with a 150 millidegree
offset. This is a bit confusing, as it also differs from other CrOS EC
tooling. Internally the EC uses a kelvin to celsius offset of a round
273, so the current conversion is also not entirely accurate.
Implement a custom conversion which preserves round values.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20260630-cros_ec-hwmon-overflow-v1-1-3d2ecd3eb0f2@weissschuh.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a driver for the temperature and voltage sensors on PolarFire SoC.
The temperature reports how hot the die is, and the voltages are the
SoC's 1.05, 1.8 and 2.5 volt rails respectively.
The hardware supports alarms in theory, but there is an erratum that
prevents clearing them once triggered, so no support is added for them.
The hardware measures voltage with 16 bits, of which 1 is a sign bit and
the remainder holds the voltage as a fixed point integer value. It's
improbable that the hardware will work if the voltages are negative, so
the driver ignores the sign bits.
There's no dt support etc here because this is the child of a simple-mfd
syscon.
Signed-off-by: Lars Randers <lranders@mail.dk>
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20260629-wriggle-headscarf-c85a4070dddb@spud
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
